Tanaka TCG27EBSP Support Question
Tanaka TCG27EBSP Support Question
Find answers below for this question about Tanaka TCG27EBSP.Need a Tanaka TCG27EBSP manual? We have 2 online manuals for this item!
Question posted by jrm2a52 on March 7th, 2019
Trimmer Head Runs When Started And At Idle
is it a broken clutch spring How do I get parts
Current Answers
Answer #1: Posted by waelsaidani1 on March 7th, 2019 10:20 AM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,797
Member since:
May 12th, 2013 Points: 19,501,797
A broken spring is usually responsible for this type of malfunction, but it can also be caused by corrosion. The spring is replaceable if broken. Parts are available here: https://www.ereplacementparts.com/tanaka-trimmer-parts-c-34785_34906.html
Related Tanaka TCG27EBSP Manual Pages
Owner's Manual - Page 2
... max rpm is correctly assembled and adjusted. • Start the unit and check the carburetor adjustment. Ignition stop ...Run position (Open)
Choke -
If anyone approaches you read, fully understand and observe the following show symbols used for a trimmer head or semi-auto cutting head. Before using this unit. Fuel and oil mixture
Keep all warnings and instructions in this point. Start...
Owner's Manual - Page 4
...from the unit. ○ Move at least 10 ft (3 m) away from fueling site before starting engine. ○ Stop engine before removing fuel cap. ○ Empty the fuel tank before using... engine. ○ Wear head protection. ○ Never start or run the engine inside a closed environment, such as the device manufacturer prior to operating any way. Replace damaged parts. Do not use your physician...
Owner's Manual - Page 5
...; Keep others away when making carburetor
adjustments. ○ Use only genuine Tanaka replacement parts as
recommended by the following words:
WARNING Indicates a strong possibility of severe personal injury...use the unit/machine in accordance with recoil spring.
5
English
WARNING Fuel is easy to be cut any power equipment. ○ Never start or run the engine inside a closed room or ...
Owner's Manual - Page 6
in.) Spark plug
Idling speed (min-1) Speed of output shaft (min-1) Max. engine output (kW)
Fuel tank capacity (fl. English
SPECIFICATIONS
Model
Engine Displacement (cu. oz)
Dry weight (Ibs)
...
Owner's Manual - Page 7
... (dB (A)) Racing
Vibration level (m/s2) (ISO22867)
Equivalent (Front / Left handle)* Equivalent (Rear / Right handle)* Uncertainty
TCG27EBSP (SL)
TCG27EBDP (SL)
1.64 (26.9 ml) NGK BMR7A 2,800 - 3,200
7,600 0.9
1.64 (26.9 ml...time distribution: * 1/2 Idle, 1/2 racing. English
Model
Engine Displacement (cu. All data subject to change without notice.
7 in.) Spark plug Idling speed (min-1) Speed...
Owner's Manual - Page 8
.... 3) Store stop cord Press the upper tab (4) and open the air cleaner cover. (Fig. 3)
8 Fig. 5
8 Adjust the location to the drive shaft tube with the parts installed.
7 6
10
11
5
NOTE
If your unit has handle location label on your unit, screw it . 2. English
ASSEMBLY PROCEDURES
4
Installation of tube and that the...
Owner's Manual - Page 9
Installation of semi-auto cutting head
Fig. 6
Installation of the button, change the new parts immediately. (Fig. 8)
13
14
Fig. 7
NOTE The guard bracket may come already... guard is a hole in the bottom (14) of cutting attachment guard (Fig. 7)
WARNING ● Do not start or operate unit unless each
guard is properly assembled to the gear case using the two guard mounting screws. If the...
Owner's Manual - Page 10
....
3. English
○ If the cutting head does not feed cutting line properly, check that the nylon line and all components are properly installed.
Always run the engine on your Tanaka dealer if you...each tap. (Fig. 10)
Fig. 12
WARNING ● The trimmer is equipped with oil. Installation (Fig. 9) ○ Install cutting head on the ground. The mounting nut is not available, use an anti...
Owner's Manual - Page 11
...)
Fig. 15
3. When you hear the engine want to start, return choke lever to RUN position (open the fuel tank, when filling up before starting , make sure the cutting attachment does not touch anything.
1. Add the remaining amount
18
of oil. Starting
CAUTION Before starting . ● Always wash any spilled fuel from clothing immediately...
Owner's Manual - Page 12
...engine and attachment and remove them. Semi-auto cutting head ○ When cutting, operate engine at low rpm may wear out the clutch prematurely. ○ Cut grass from right to ...Stopping (Fig. 20) Decrease engine speed and run at over 6,500 min-1.
Cutting (Fig. 17, 18, 19) ○ When cutting, operate engine at an idle for efficient cutting.
Keep onlookers out of...
Owner's Manual - Page 13
... after idle speed adjustment, contact your Tanaka dealer. Carburetor adjustment (Fig. 21) T
English
○ Carburetor malfunctions ○ Starting problems ○ Engine power reduction ○ Unnecessary wear on the engine parts ○ Abnormal fuel consumption
Clean the air filter daily or more often if working in warm water with detergent. Otherwise the clutch can...
Owner's Manual - Page 14
...if necessary. The correct gap is low on power, difficult to start or runs poorly at idling speed, always check the spark plug first. The spark plug should be... about 100 operation hours or earlier if the electrodes are badly eroded.
0.024" (0.6 mm)
Semi-auto cutting head
Nylon line replacement (1) Remove the case (22) by firmly pushing inward
the locking tabs with resistor spark...
Owner's Manual - Page 15
... the space around it
to 3/4. ○ Clean the air filter.
Adjust it .
15
Weekly maintenance ○ Check the starter, especially the cord and return
spring. ○ Clean the exterior of defects. For further information please contact your Tanaka dealer. An off-centre cutting attachment induces heavy vibrations that may damage...
Owner's Manual - Page 16
... the problem, consult your dealer or the Tanaka dealer. Condition
Fuel system Engine does not start
Electrical system
Other
Cause
Remedy
Fuel tank is empty or fuel level is Fill the fuel...handle 5 or 6 times to remove the surplus fuel
3.Attach the spark plug 4.Set the choke lever to RUN position
and pull the starter handle
Fuel filter is clogged with dirt
Clean the fuel filter
Fuel...
Owner's Manual - Page 17
...added Contact Tanaka dealer
Choke lever is in START position Set the choke lever to RUN position
Air has got into fuel system
... "Installation of cutting attachment"
Handle, handle bracket or other fastening part is loose
Check and tighten
Blade is bent or damaged
Replace with... failure
Idle speed is too low Idle speed is too high Throttle wire is too taut
Set the choke lever to START position...
Parts List - Page 4
...
1
20 6699437 INTAKE PACKING
1
21 6698387 CARBURETOR INSULATOR
1
22 6698844 SEAL LOCK HEX. PARTS
ITEM NO. USED
2
REMARKS
2 6600322 MUFFLER COVER
1
3 6698384 HEX. SOCKET HD. BOLT...ASS'Y
1 INCLUD.43-46
48 6698366 CYLINDER PACKING
1
49 6686121 PISTON RING
2
- 4 -
*ALTERNATIVE PARTS
TCG 27EBSP 4 - 14 DESCRIPTION
1 887021 SCREW (W/WASHERS) M5 X 16 (BLACK)
NO. SOCKET HD. ...
Parts List - Page 5
...* 95 6699192 STOP LEVER
1 FOR (SL)
* 96 6699191 LONG LEVER
1 FOR (SL)
* 97 6699193 RETURN SPRING
1 FOR (SL)
* 98 6699190 STAY SET
1 FOR (SL)
* 99 6699133 THROTTLE LEVER (A) ASS'Y
1 INCLUD...108 6699435 BALL BEARING 6301ZZC3
1
109 322813 RETAINING RING 37MM
1
4 - 14
*ALTERNATIVE PARTS
TCG 27EBSP - 5 - PARTS
ITEM NO. USED
1
REMARKS
51 6684590 CIR CLIP
2
52 6684591 PISTON PIN
1
53...
Parts List - Page 6
...12/W.S
1
164 6600005 CAP
1
165 6600006 SPRING
1
166 6684737 BOLT (W/PLUS) M6 X 8
1
167 6600007 LOCK PIN...EUROPE
* 169 6698659 CUTTER HOLDER (B)
1 FOR EUROPE
- 6 -
*ALTERNATIVE PARTS
TCG 27EBSP 4 - 14
HOLE BOLT M5 X 25/S
4 FOR (S)
*...112 6684648 BENT WASHER 8
2
113 6696546 CLUTCH PLATE (A)
2
114 6699130 CLUTCH
1
115 6699131 CLUTCH WASHER (B)
2
116 6685337 FLYWHEEL NUT
1
...
Parts List - Page 7
PARTS
ITEM NO. SOCKET HD. WASHER) M4 X ...)
1 FOR EUROPE
TCG 27EBSP
4 - 14
*ALTERNATIVE PARTS
- 7 - CODE NO.
* 170 6699188 NUT COVER
DESCRIPTION
NO. BOLT (W/BUTTON) M6 X 20 2 FOR USA
* 186 949455 SPRING WASHER M6 (10 PCS.)
2 FOR USA
* 187 6696978... 6698939 REEL
1
176 6698941 RETURN SPRING
1
177 6698940 BUTTON
1
178 6698942 CORD GUIDE
2
179 6698938 CASE
1
180 6698639 NYLON...
Parts List - Page 8
... 8 X 10
503 944458 HEX. STANDARD ACCESSORIES
ITEM NO.
USED
1
REMARKS
1 FOR EUROPE
1
2 FOR (S)
1
1 FOR EUROPE (SL)
1 FOR (S)
1 FOR (S)
1 FOR USA
1 FOR USA
TCG 27EBSP
- 8 -
*ALTERNATIVE PARTS
Printed in Japan 4 - 14
(140425N)
Similar Questions
Hard Starting
Very difficult to start. Why? Once running it runs well.
Very difficult to start. Why? Once running it runs well.
(Posted by coffb 10 months ago)
I Start It When I Give It Gas It Doesn't Rev Up When I Give It Gas
(Posted by Dumper 2 years ago)
Tanaka Tch22ebp2 22' Hedge Trimmer Replacement Carburetor
Hi! Can you tell me where I might find a replacement carburetor for a 22" gas powered Tanaka hedge t...
Hi! Can you tell me where I might find a replacement carburetor for a 22" gas powered Tanaka hedge t...
(Posted by Biogal930 3 years ago)
Can Quick Load Heads Be Installed On This Unit Tanaka Model Tcg24ebsp (sl)
Can quick load heads be installed on this unitTanaka model TCG24EBSP (SL)
Can quick load heads be installed on this unitTanaka model TCG24EBSP (SL)
(Posted by Deborahaunger 8 years ago)
Starting Issues
Hello,I have a tanaka tbl 505 backpack leaf blower that won't start. The spark plug is sparking, the...
Hello,I have a tanaka tbl 505 backpack leaf blower that won't start. The spark plug is sparking, the...
(Posted by Sn19labriem 9 years ago)