Troy-Bilt Storm 2410 Support Question
Troy-Bilt Storm 2410 Support Question
Find answers below for this question about Troy-Bilt Storm 2410.Need a Troy-Bilt Storm 2410 manual? We have 1 online manual for this item!
Question posted by rocky2007js on July 23rd, 2014
Troy Bilt Th6040
Only a year old it start right up but won't go full throttle it keeps quitting! And also leaks oil out of the air filter.
Current Answers
Related Troy-Bilt Storm 2410 Manual Pages
Operation Manual - Page 1
..., OHIO 44136-0019
Form No. 769-06897 (May 17, 2011)
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. Printed In USA
TROY-BILT LLC, P.O. Storm 2410, 2620, 2840 & 3090XP
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. Safe Operation Practices •...
Operation Manual - Page 2
... that you, and any problems or questions concerning the machine, phone a authorized Troy-Bilt service dealer or contact us on the web at www.troybilt.com ◊ Call...product specifications for purchasing a Troy-Bilt Snow Thrower. Please be sure that this manual frequently to the retailer or dealer without incurring obligation. We reserve the right to the engine manufacturer's Owner...
Operation Manual - Page 3
...could result in operation. Never allow children under 14 years of age to the safe operation practices in this machine. Keep bystanders, pets and children at least 75 feet ...could endanger the personal safety and/or property of the operator can result in this manual before starting the engine.
6. Read, understand, and follow all controls and their proper operation. Important Safe...
Operation Manual - Page 4
...for
released. Contact with a portable container, rather than you
l. unclogging.
19. When starting the engine.
13. Wash your nearest servicing dealer.
4.
Exercise caution when changing direction and... return to vibrate abnormally, stop engine before
Operation
1. storing.
16. Keep the nozzle in front of the machine. Use only attachments and accessories approved...
Operation Manual - Page 5
...instructions on federal lands. Refer to keep the machine in accidents, injuries or ... regulations for cracks or leaks. Prior to storing, ... Oxidizing Catalyst (OC), Secondary Air Injection (SAI) and Three ... and fittings frequently for gas, oil, etc.
Clearing a Clogged Discharge...starting.
3. Environmental Protection Agency (EPA), this product has an Average Useful Life of seven (7) years...
Operation Manual - Page 6
...and follow all instructions in this manual and on the machine before touching. ROTATING BLADES Keep hands out of inlet and discharge openings while machine is running .
warning!
CARBON ... Do not use of this product. SAVE THESE INSTRUCTIONS!
6
Section 2 - ROTATING BLADES Keep hands out of inlet and discharge openings while machine is running .
Allow engine and muffler...
Operation Manual - Page 7
... Observe the lower rear area of the snow thrower to be sure
both the left and right sides of Carton
• One Snow Thrower • One Snow Thrower Operator's
Manual &#... Make certain the cables are for packaging purposes only. See Fig. 3-2. 3.
Figure 3-2
Chute Assembly (Model 2410)
1. Place the shift lever in the roller guides. Position the chute assembly over the base. Assembly & Set...
Operation Manual - Page 8
... the chute directional control. See Fig. 3-6. Chute Control Head
Chute Support Bracket
Chute
Chute Base
Figure 3-4
Figure 3-6
Chute Directional Control (Model 2410)
2. Push rod as far into chute control head as possible, keeping the
1. Remove the plastic cap (if present), flat washer and hairpin
holes in the rod pointing upward.
See
Fig. 3-5.
Operation Manual - Page 9
... joystick to the one o'clock position so that the silver indicator arrow on the joystick and rotate the chute by
Figure 3-10
hand to the right at this time. Squeeze the trigger on the pinion gear below the joystick. The holes in the chute control input will not rotate without squeezing...
Operation Manual - Page 11
...Move skid shoes to side wall of the chute assembly. Chute Assembly (Models 2410 and 2620)
NOTE: The upper chute on each side) and carriage bolts.... tire pressure before retightening the wing knob. Insert Key into engine and start engine. Adjustments
Skid Shoes
The snow thrower skid shoes are over-inflated for...surface, keep the skid shoes in a straight path and the shave plate may wear ...
Operation Manual - Page 12
... control.
7. See Fig. 3-18. Position the bracket upward to provide more slack (or downward to Engine Operator's Manual.
3. In a well-ventilated area, start the snow thrower engine. With the throttle control in the FAST (rabbit) position and the auger control in the disengaged "up " position, the cable should NOT be tight.
2. Confirm...
Operation Manual - Page 13
... If Equipped
Figure 4-1
Snow thrower controls and features are described below and illustrated in the right side of the handle panel and is used to determine ground speed and direction of the handle... panel and is automatically turned on when the engine is started.
13
Adjust downward when operating on surface conditions.
Augers
When engaged, the augers rotate...
Operation Manual - Page 14
... the dash panel.
• To change the direction in which snow is thrown, squeeze the button on the right handle. Failure to stop . Controls and Features Auger Control
Standard Chute Directional Control (if so equipped)
T
The... located on the joy-stick and pivot the joy-stick to the right or to the OFF position.
14
Section 4 - Release to engage the wheel drive. Release to engage...
Operation Manual - Page 15
...which snow is thrown, squeeze
the button on the joy-stick and pivot the joy-stick to the right or to safely clean the chute assembly and chute opening:
1. Steering Trigger Controls (if so equipped)
...secures it to the mounting clip on the rear of the auger housing, reinsert the key and start the snow thrower's engine. 4-Way Chute Directional Control (if so equipped)
The 4-way chute ...
Operation Manual - Page 17
... of operation.
1. When one side wears out, they can be careful not to the inside of engine oil (or 3-in -1 oil.
17
Refer to the Engine Operator's Manual.
Tighten securely. Standard Chute Directional Control (Model 2410)
Once a season, lubricate the eye-bolt bushing and the spiral with the four carriage bolts (two on...
Operation Manual - Page 19
...not fully engaging with the second hole in an unventilated area,
rustproof the machine using a light oil or silicone to lack of fuel. See Fig. 6-6. Off-Season Storage
If the snow thrower ...Do not attempt to the chute assembly on adjusting the chute assembly.
Chute Bracket Adjustment (Model 2410)
If the spiral at the bottom of the engine and the snow thrower.
See Fig. 6-7. Reinsert...
Operation Manual - Page 22
...increase the clearance between friction wheel and friction wheel disc. Stop Bolt
Friction Wheel Removal (Models 2410, 2620 & 2840)
If the snow thrower fails to drive with the drive control engaged, ...until it . Do not attempt to replace the snow thrower's friction wheel rubber. Remove the right-hand wheel by removing four self-tapping screws which secure it is out of wear or cracking...
Operation Manual - Page 25
... 684-04159 935-04054
Auger Drive Belt (Storm 2410 & Storm 2620 with 15" tires) Auger Drive Belt (Storm 2840 & 3090XP & Storm 2620 with 16" tires) Wheel Drive Belt (Storm 2410 & Storm 2620 with 15" tires) Wheel Drive Belt (Storm 2840 & 3090XP & Storm 2620 with 16" tires)
Friction Wheel Assembly (Storm 2410, 2620 & 2840) Friction Wheel Assembly (Storm 3090XP) Friction Wheel Rubber
725-1629...
Operation Manual - Page 26
... Snow Thrower Protective Cover Troy-Bilt Snow Thrower Maintenance Kit
26 Attachments & Accessories
10
The following attachments and accessories are available for information regarding compatibility, price and availability (have your Troy-Bilt snow thrower.
Model Number
Description
753-05762A OEM-390-679 490-241-0010 OEM-390-995 490-241-Y014 *Not compatible with Storm 2410.
Operation Manual - Page 28
...and possessions, and by Troy-Bilt for a period of two (2) years commencing on the date...rights, and you may not apply to temporarily replace a warranted product. KITCHENER, ON N2G 4J1; Normal Wear Parts are not limited to use or exposure. Troy-Bilt...because of purchase. Routine maintenance items such as lubricants, filters, blade sharpening, tune-ups, brake adjustments, clutch adjustments...
Similar Questions
Troy Bilt Snow Blower Engine (storm 2410)
I need to remove the shroud from the engine, and to do so I have to remove the choke knob. Can you t...
I need to remove the shroud from the engine, and to do so I have to remove the choke knob. Can you t...
(Posted by dcook37366 1 year ago)
Troy Bilt 22tb Weed Eater Trouble
Mt Troy-Bilt 2TB Weed Eater has had Bumper and Head replaced 2 times. Both were replaces because Bum...
Mt Troy-Bilt 2TB Weed Eater has had Bumper and Head replaced 2 times. Both were replaces because Bum...
(Posted by denisstpierre1961 1 year ago)
Tb225 Starter Rope Replacement. How To Replace The Starter Rope On A Troy-bilt T
how to replace the starter rope on a Troy-Bilt TB 225 garden cultivator?
how to replace the starter rope on a Troy-Bilt TB 225 garden cultivator?
(Posted by hamptona0000 6 years ago)
My Troy Bilt 2410 Start And Stops Rightaway And I Think Gas Is Leaking From Car
(Posted by yogi384 10 years ago)