JET Tools J-4002 Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools J-4002 manuals!
Problems with JET Tools J-4002?
Ask a Question
Free JET Tools J-4002 manuals!
Problems with JET Tools J-4002?
Ask a Question
JET Tools J-4002 Videos
Best Belt & Disc Combo Sanders 2022 - Jet Tools - J-4002
Duration: 1:38
Total Views: 86
Duration: 1:38
Total Views: 86
Popular JET Tools J-4002 Manual Pages
User Manual - Page 1
This .pdf document is bookmarked
Operating Instructions and Parts Manual
Belt and Disc Sander (1x42" belt, 8" disc)
Model J-4002
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No. M-577003 Revision B 04/2015
(ECR TW0134) Copyright © 2015 JET
User Manual - Page 2
...Hoists; Warehouse & Dock products; Parts; Heavy-Duty Air Tools; More Information JET is constantly adding new products. Consumable items; 1.0 Warranty and Service
JET warrants every product it sells against manufacturer's defects.
JET reserves the right to Get Technical Support Please contact Technical Service by a 90 day limited warranty against manufacturers' defects.
Manual Hoists;
User Manual - Page 3
...J-4002 Disc Parts - Parts List ...14 13.2.1 J-4002 Disc Parts - Parts List ...17
3 2.0 Table of contents
Section
Page
1.0 Warranty and Service...2 2.0 Table of contents...3 3.0 Safety Warnings...4
3.1 General Cautions ...4 3.2 General Machinery Warnings...4 3.3 General Electrical Cautions...5 3.4 Safety Instructions for the Belt/ Disc Sander 5 4.0 About this manual ...6 5.0 Specifications...
User Manual - Page 4
....
7. Never modify the machine without consulting JET. Read and follow the instructions in the machine. No loose clothing or jewelry which does not comply with ANSI Z87.1 specifications could result in severe injury from the electrical power before plugging in the Operating Instructions and Parts Manual when changing accessory tools or parts.
- Failure to the machine. Do not...
User Manual - Page 5
... moving parts and ... Code and local codes ...tool you do a job for which could be done by a qualified electrician. The sander motor requires 120 volts alternating current. If there is completely assembled and installed...specifically designed to these chemicals are too small to a supporting...silica from the electrical service box, the wire...follow manufacturer's instructions pertaining to cause...
User Manual - Page 6
... the machine has come to comply may cause serious injury!
5.0 Specifications
Model number ...J-4002 Stock number ...577003 Disc speed ...1,725 RPM Disc diameter ...8 in water to change specifications at time of publication, but because of our policy of water on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown.
User Manual - Page 7
... in support casting (see sect. 10.4.2).
7.2 Assembling belt sander table
1. Tighten stud finger tight. Install handle over stud. Figure 4: Belt table installed, handle in clockwise direction. If any parts are missing, do not attempt to operate your sander until the machine is completely assembled and you have read and understood the entire Operating Instructions and Parts Manual...
User Manual - Page 8
...Setup
8.1 Fastening sander to supporting surface
During operation, the sander may be sure that electric current is of same characteristics as stamped on left side of electric shock. It is properly grounded. Two holes are not completely understood, or if in grounded receptacle
Repair or replace damaged or worn cord immediately.
This tool...service personnel if the grounding instructions...
User Manual - Page 9
... making any adjustments.
10.1 Sanding belt tracking
The belt tracking adjustment is set at 90degree angle to properly support the work or fingers between table and sanding belt, the table edge should...can be tilted or moved in or out to accommodate the operation being performed. Figure 12: Setting belt table to change angle, loosen locking handle. Loosen cap screw and adjust platen to ...
User Manual - Page 10
... IMPORTANT: Some belts have a directional arrow printed on inside of disc. Figure 13: Setting belt table to 45-degrees
10.4 Disc table adjustments
10.4.1 Adjusting disc table angle
To...source. The sanding belt travels down on the table with two knobs.
Replace side cover; The disc table is running. Install replacement belt.
5. Use T-handle type hex wrench. Move disc in top of...
User Manual - Page 11
Disconnect machine from sanding disc table.
Remove disc from power source.
Replace lower disc guard and sanding disc table.
10.7 Miter gauge
A miter ...of disc plate.
10. Figure 22: Disc installation
9. Remove lower disc guard (see Figure 21). Install disc plate on disc table or belt table. The miter gauge can be set anywhere up to desired angle and retightening knob...
User Manual - Page 12
...JET Sander:
Sharpening a wood chisel on the sanding belt using the miter gauge as a guide... (see Figure 26). Sanding on right side of sander base. Figure 8: On/Off switch
11.2 Locking switch in OFF position
We recommend that can be turned OFF once, but it can be performed with the table tilted and using a block of wood. Move switch to rear (OFF) position to support... instructions
...
User Manual - Page 14
... Set Screw M5x5 1
14 To order parts or reach our service department, call will allow us to serve you call 1800-274-6848 Monday through Friday (see our website for business hours, www.jettools.com). Having the Model Number and Serial Number of your machine available when you quickly and accurately.
13.1.1 J-4002 Belt Parts - 13.0 Replacement Parts
Replacement parts...
User Manual - Page 15
...M10x20 2 103 5640561 Rotation Label 1 104 JET-113 JET Logo (not shown 113x47mm 1
15 Index No Part No
Description
Size
Qty
12 5640191 Hex Socket Set Screw M5x12 1 13 5640251 Drive Pulley...1... 6202ZZ 1 33 5640371 Idler...1 34 5640491 Retaining Ring 1 35 TS-1523011 Hex Socket Set Screw M6x6 1 36 5640521 Drive Wheel 1 37 5640101 Sanding Belt 50 Grit 5640111 Sanding...
User Manual - Page 17
...J-4002 Disc Parts - Belt/Disc 1 107 5640931 V-Belt ...1 5640941 Miter Gauge Assembly (#110~114 1 110 5640961 Hand Knob 1/4 in 1 111 5640971 Flat Washer 3/16 in 1 112 5640981 Miter Gauge Body 1 113 5640991 Spring Pin M4x10 1 114 5641011 Guide ......1 101 TS-1523011 Socket Set Screw M6x6 1 102 5640881 Screw...1 103 5640561 Rotation Label 1 106 5640921 Pulley Cover -
JET Tools J-4002 Reviews
We have not received any reviews for JET Tools yet.