JET Tools J-8201VS Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools J-8201VS manuals!
Problems with JET Tools J-8201VS?
Ask a Question
Free JET Tools J-8201VS manuals!
Problems with JET Tools J-8201VS?
Ask a Question
Popular JET Tools J-8201VS Manual Pages
User Manual - Page 1
M-414500 Revision C1 03/2014 Copyright © 2014 JET This .pdf document is bookmarked
Operating Instructions and Parts Manual
14-inch Vertical Band Saws
Models: J-8201, J-8203, J-8201VS, J-8203VS
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No.
User Manual - Page 2
... information, check with a Five Year Warranty that you specific legal rights, subject to Get Technical Support Please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through distributors only.
Product Listing with any time, without prior notice, those alterations to the JET brand.
2 Who is constantly adding new products.
Warranty...
User Manual - Page 3
... List - Models J-8201,J-8203,J-8201VS and J-8203VS 26 Exploded View - Table of contents
Section
Page
Warranty and Service...2 Table of contents...3 Warning ...4 Machinery General Safety Warnings ...4 General Electrical Cautions...5 Switch Padlock ...5 Safety Instructions for Sawing Systems...6 Specifications ...7 Introduction ...8 Band Saw Features...8 Setup and Operation ...8
Set-up...
User Manual - Page 4
... Z87.1)
- Machinery General Safety Warnings
1. When setting up , used and serviced properly.
- The smaller the gage number, the heavier the cord.
10. Read and follow instructions in moving parts. W arning
- Never modify the machine without consulting JET Tools. All visitors should read and understand the Operating Instructions and Parts Manual as well as blades, bits, cutters, and...
User Manual - Page 5
...
10
12
16
16
14
12
12
16
14
12
Not recommended
Only the applicable parts of injury to the following instruction: The installer shall follow local regulations and National Electrical Code, ANSI/NFPA 70 installation requirements.
5 B).
3.
For three phase tools without the lock-off position before plugging in order to deliver ample voltage to the...
User Manual - Page 6
... in contact with ANSIZ87.1 specifications. Always wear protective eye wear when operating, servicing, or adjusting machinery. Eyewear shall be securely clamped before any attempt is performed on the saw blade. Wear ear protectors (plugs or muffs) during extended periods of blade support mechanism is done, or before any periodic service or maintenance is made...
User Manual - Page 7
...325 325
The specifications in thick or thin stock.
Model number J-8201K J-8203K J-8201VS J-8203VS Stock number 414500 414504C 414502 414503
Capacities: Under Guide (in 6 6 6 6 Under Guide with an infinitely ... curves in this manual were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time ...
User Manual - Page 8
... in the Electrical section to level the saw . This manual also includes parts listings and illustrations of the four lug holes.
Refer to the Specifications section for attachment as required to complete the electrical hookup.
8 Figure 1: Band Saw Features - Front View (All Models
Setup and Operation
Set-up the sight gauge. (Two containers of the saw...
User Manual - Page 9
....
Repair or replace damaged or worn cord immediately.
9 NOTE: Observe all local codes and ordinances. Always use a licensed electrician for electric current to whether the tool is not going downward into the table slot. Electrical
Models J-8201 and J-8201VS are delivered with an electric cord having an outer surface that accept the tool's plug.
Instead, follow these instructions...
User Manual - Page 10
... a grounded metal permanent wiring system; The temporary adapter should be used to connect this tool. Make sure the tool is available or should be used with all local codes and ordinances.
4. If the tool must be installed by qualified service personnel; The tool has a grounding plug that looks like the plug illustrated in Sketch A. A temporary adapter, which...
User Manual - Page 13
... hardening of the cut can save you time, trouble, and the possibility of dulling and premature discarding of..., such as stainless steel, require the cut and the service life of materials.
the wider widths are used for more...Instructions
Saw blades
The JET14-inch saws accept blades from 1/8inchwide to Material Chart
13 Different blade materials and tooth geometry (pitch and set...
User Manual - Page 15
...the table is level while everything is running. Turn the speed adjustment knob to the desired setting as required to make the table square to working tightness.
10. Put a straight edge against...the clutch mechanism while the saw . If the measurements are being cut. Adjusting Blade Speed (Models J8201VS/J-8203VS)
See Figure 10. When the table is provided on the barrel of three points on...
User Manual - Page 19
...surface of service, the protectors wear and may require replacement. Replace the drive belts. Close the access door. 11. Then tighten the set screws securely...service by following the steps in the base. 3.
19. Adjust the upper support assembly so the support bearing just contacts the back edge of the blade to sure the blade is halfway up on the motor to the step-bystep instructions...
User Manual - Page 20
... signs of missing teeth
Whenever operating saw
Replace blade when bent - replace if damaged or excessively worn
Replace a glazed belt - Watch for level - Periodic Maintenance
Item Saw blade
Lower drive wheel Upper drive wheel Drive wheel rubber protectors Drive belts
Reduction gearbox
Blade support bearings Carbide blade guides
Action
Interval
Maintenance
Listen for sound of...
User Manual - Page 26
Models J-8201,J-8203,J-8201VS and J-8203VS
Index No Part No
...Fixed Bolt...2 13 5782751 Catch ...2 14 170080 Stud Latch...2 15 TS-1522021 Set Screw M5x8 2 16 5782831 Blade Guard 1 17 5782841 Retainer ...2 18 J-... Spacing Sleeve 2 39 5783391 Carbide Blade Guide 4 40 5783631 Lower Support Bracket Post 1 42 5783591 Bracket Trunnion Support 1 43 5783611 Point...1 44 J-5783451...
JET Tools J-8201VS Reviews
We have not received any reviews for JET Tools yet.