JET Tools JTM-4VS Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools JTM-4VS manuals!
Problems with JET Tools JTM-4VS?
Ask a Question
Free JET Tools JTM-4VS manuals!
Problems with JET Tools JTM-4VS?
Ask a Question
JET Tools JTM-4VS Videos
9" x 49" Brand New Jet Industrial Vertical Milling Machine, Mdl. JTM-4VS, SMJTM4VS
Duration: 7:18
Total Views: 1,601
Duration: 7:18
Total Views: 1,601
Popular JET Tools JTM-4VS Manual Pages
User Manual - Page 1
This .pdf document is bookmarked
Operating Instructions and Parts Manual
Variable Speed Turret Mill
Model JTM-4VS
Shown with optional accessories X-Axis Table Powerfeed and DRO
JET
427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No. M-690182 Revision H3 01/2015 Copyright © 2015 JET
User Manual - Page 2
... used for wood turning. For complete, up-to Get Technical Support Please contact Technical Service by JPW Industries, Inc. JET® branded products are made specifically for commercial or industrial purposes default to the JET brand.
2 Consumable items; Motors; Heavy-Duty Air Tools; Manual Hoist Accessories; Warehouse & Dock products; Warranty Limitations Woodworking products...
User Manual - Page 3
...Container...7 Set-up and Installation ...8
Preparing the Milling Machine for Head Assembly...26 Spindle Assembly ...29
3 Table of Contents
Section
Page
Warranty and Service...2 Warnings ...4 Introduction ...6 Specifications...6 Unpacking...7
Contents of Quill Feed Clock Spring...24 Replacement Parts...24 Head Assembly ...25 Parts List for Service ...8 JTM-4VS Dimensions ...9 JTM-4VS Overview...
User Manual - Page 4
...specifically designed to filter out microscopic particles. 10. Read and understand all loose clothing and confine long hair. Do not operate this manual...been obtained. 5. Base Assembly...33 Parts List for machining contain chemicals that ... and intended for other purposes, JET, disclaims any real or implied ... Do not use extreme caution and replace the guards immediately. 16. To reduce...
User Manual - Page 5
... lean against the cutters or other conditions that may result in this manual: This means that is damaged should be hazardous. 25. Check for
which it may be properly repaired or replaced.
18. Looking around the machine clean and free of parts, mounting and any machine operation. 23. Use recommended accessories; Familiarize yourself with...
User Manual - Page 6
... (in 14-1/2 14-1/2
Ram Travel, maximum (in 13-3/8 13-3/8
Overall Dimensions (in this manual. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. Introduction
This manual is provided by JET, covering the safe operation and maintenance procedures for a JET Model JTM-4VS Turret Milling Machine.
User Manual - Page 7
... for assembly, maintenance and safety instructions. Report any , should be reported to your distributor. Compare the contents of this manual before attempting set-up or operation! Missing parts, if any damage immediately to your distributor and shipping agent. Failure to make sure all parts are also included in the tool box service kit, p/n JTM4VS-TB.
If your container...
User Manual - Page 8
...support sling over its rollpin engages the hole in the Adjustments section for Service
1. Unwrap and clean the knee crank and install... corners. If so, ignore the instructions related to those particular steps. Install the table traverse and cross-feed ... over 2400 pounds! Set-up and Installation
Preparing the Milling Machine for procedures to safely raise and set up the mill head...
User Manual - Page 10
JTM-4VS Overview and Terminology
Figure 3: Overview 10
User Manual - Page 11
...far away from the electrical service box, the wire size ...setting is on the upper left-hand side of the machine. The switch has three positions: FWD (forward), STOP, and REV (reverse). Use FWD for 230 volt operation.
The JTM-4VS has been pre-wired for normal, right-hand tooling... Electrical Code and local codes and ordinances. Lubrication
Operating Instructions
Operating Controls...
User Manual - Page 14
... the power feed will retract the spindle automatically once the handle is upfeed. Remove the Manual Fine Feed Handwheel when not in and out position. Secure with Micrometer Adjusting Nut (A, ...is located on the right side of the head.
Fine Feed Handwheel
When the controls are set for setting specific spindle depth. Rotate the handle clockwise to release. Figure 13 14 Feed Trip Cam Lever
...
User Manual - Page 15
...of the mill head. Figure 15
The overload clutch is located on the front of the tooling, coolant, and material for drills larger than 3/8". Do not attempt to comply may cause serious...Control Handwheel (E).
10.
Use manual feed for specific recommendations. Referring to Figure 17:
Be sure that have data applicable to 3/8"). The depth scale is factory set the depth of a Micrometer ...
User Manual - Page 16
...2. Figure 20
2. Turn the worm nut (B, Figure 20) to support the mill head, taking some weight off the brass worm gears. ...Set motor switch to use . Tighten in two steps using the wrench provided with the machine, loosen the draw bar two or three turns (turn should be slightly higher in two steps using a crossing pattern.
Changing Tooling
1. Figure 18
2. Insert the tool you are guides...
User Manual - Page 26
Part No. Description
Size
Qty
JTM4VS-HA Head Assembly w/ Motor 1 1 VS-001 Upper Housing 1 2 VS-002 Motor Pulley ...1 VS-044A Motor Pulley Bushing (not shown 1 3 TS-1503011 Set Screw M6 x 6 4 4 VS-004 ... VS-040 Spring Pin 3/32" x 3/4 1 41 VS-041 Washer...1 42 VS-042 Support...1 43 BB-6010VV Ball Bearing ...2 44 VS-044 Driven Pulley Assembly (s/n:xxx1944 & lower ...
User Manual - Page 35
...Hex Socket Cap Screw M8 x 12 1 79 JTM4VS-B79........... Grease Nipple 1/8"PT 1 80 JTM4VS-B80........... Turret Scale...1 82 JTM4VS-B82........... Part No. Lock Washer...1 98 RIBW34 Hoisting Ring ...1... Key 3 x 3 x 20 mm 1 106 ...........LS-006B Saddle Ratcheting Lever 3 JTM4VS-TB Tool Box Kit Complete (not shown 1 LC051 Plastic Electric Cover (not shown 1 LC051A Plastic...
JET Tools JTM-4VS Reviews
We have not received any reviews for JET Tools yet.