JET Tools JJP-12 Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools JJP-12 manuals!
Problems with JET Tools JJP-12?
Ask a Question
Free JET Tools JJP-12 manuals!
Problems with JET Tools JJP-12?
Ask a Question
JET Tools JJP-12 Videos
JET JJP 12 12 Inch Jointer Planer
Duration: 2:01
Total Views: 1,369
Duration: 2:01
Total Views: 1,369
Popular JET Tools JJP-12 Manual Pages
User Manual - Page 1
This .pdf document is bookmarked
Operating Instructions and Parts Manual
12-inch Jointer-Planer
Models JJP-12, JJP-12HH
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No. M-708475 Revision D 10/2014 Copyright © 2014 JET
User Manual - Page 2
... Air Tools 2 Year - 1.0 Warranty and service
JET warrants every product it sells against manufacturer's defects. Heavy-Duty Air Tools; If one year from the date of an Authorized Service Center in the literature included with a Five Year Warranty that are made specifically for any defects in the processing of maintenance.
How to applicable state law.
Manual Hoists...
User Manual - Page 3
...14.3 Mechanical troubleshooting - Planer/Jointer 25 15.0 Replacement parts ...26 15.1 Parts List for JJP-12, JJP-12HH 38 17.0 Optional accessories ...39
3 Exploded View 33 15.5 Base Assembly - Exploded View ...34 15.6 Motor Assembly - 2.0 Table of contents
Section
Page
1.0 Warranty and service ...2 2.0 Table of contents...3 3.0 Safety warnings...4 4.0 Specifications ...6 5.0 Features and...
User Manual - Page 6
...12 fpm Table movement per pass
Table 1
The specifications in minor injury and/or possible machine damage. JET reserves the right to effect, at any time and without prior notice, changes or alterations to comply may result in serious injury or possibly
4.0 Specifications
Model number JJP-12 JJP...precautions are not binding.
Failure to parts, fittings, and accessory equipment deemed ...
User Manual - Page 7
...proper direction. The Model JJP-12 and JJP-12HH Jointer-Planer is rated at least 30 amps. Features and Terminology
6.0 Receiving
Carefully unpack the machine and any , to your manual thoroughly to comply may... protected by a qualified electrician. All adjustments or repairs must be done with the machine. This machine is set up and running satisfactorily.
2. Make sure the cutterhead...
User Manual - Page 14
...installing each screw, lightly coat the screw threads with your JJP-12HH. Securely tighten each insert, rotate it 90° for a fresh edge, and re-install... inserts affected. An extra set of the rotations. Loose inserts...to Figures 11 and 12:
3.
Thoroughly clean all...Model JJP-12HH only)
10.5 Replacing or rotating knife inserts (helical cutterhead only)
The knife inserts on the model JJP...
User Manual - Page 18
... surface pieces shorter than 12 inches or thinner than 3/8 inch without the use of a push block. ‰ Cuts of a problem.
The left hand holds...part of the cut is under way, the new surface rests firmly on a jointer is to produce one flat surface (Figure 19). Investigate and correct the source of operation, see sect. 9.1, Jointer to planer setup and sect. 9.2, Planer to jointer setup...
User Manual - Page 19
...a cut of the stock, lapping over the board and extending over 12 inches long, more than 3 inches - Inspect stock for the hands... outfeed table use an infeed or outfeed support.
Surfacing
3. Figure 20 Feed with a square.
2. When ...the top of approximately 1/16 inch.
5. Direction of approximately 1/16.
4. Set the infeed table for soundness and grain direction (refer to a specified angle....
User Manual - Page 23
... too much pressure to workpiece.
Feeding workpiece too fast.
See sect. 10.3, Setting cutterhead knives.
Allow wood to dry or use different stock if necessary. Feed ...on workpiece. Sharpen or replace knives/inserts. Jointer
Trouble
Probable Cause
Finished stock is concave on back end.
14.0 Troubleshooting the JJP-12,JJP-12HH
14.1 Performance troubleshooting - Finished stock is...
User Manual - Page 24
... shallow.
Remove high moisture content from wood by drying.
Transmission v-belt slipping.
Planer
Trouble
Probable Cause
Snipe
Table rollers not set properly.
Table 3
24
Remedy
Adjust rollers to back. Note: Snipe cannot be eliminated, but can be achieve, replace feed rollers
Clean pitch and residue, and wax planer table.
Sharpen knives/Rotate knife...
User Manual - Page 25
... motor repair shop and have a starter problem.
Miswiring...Replace sprockets.
The solution is to a voltmeter, you have a power supply problem.
Verify that was the problem...problem. If voltage between starter and motor is a sure indicator of correct size. 14.3 Mechanical troubleshooting...error. Planer/Jointer
Trouble
Probable Cause Remedy
Chain jumping.
If the amp setting...
User Manual - Page 26
... Bearing 6205ZZ 2 68 708821 Knife (Set of 10 56
26 Having the Model Number and Serial Number of your machine available when you call 1-800-274-6848 Monday through Friday (see our website for JJP-12, JJP-12HH
Index No. Description
Size
Qty
1 TS-1541031 Lock Nut M8 4 2 JJP12-002 Washer 4 3 JJP12-003 Outfeed Table Bracket Shaft...
User Manual - Page 30
...2 413 Guard Plate Cover (RE: JJP12-033 1 414 Lock Plate (RE: JJP12-033 1 415 Knob (RE: JJP12-033 1 416 Nylon Bolt (RE: JJP12-033 1 417........... JJP12-390 Fence Scale 1 391........... Description
Size
Qty
339........... JJP12-369 Square Nut M8 2 370........... TS-2331081 Cap Nut M8 2 408 Locking Support (RE: JJP12-008 1 409........... Part No. TS-1541021 Lock Nut...
User Manual - Page 38
16.0 Electrical connection for JJP-12, JJP-12HH
38
User Manual - Page 39
Stock No
Description
708821 Replacement Knives for JJP-12 Jointer-planer (set of 3) 1791212 ...........Replacement Knife Inserts for JJP-12HH Jointer-Planer (set of 10) 709209 Roller Stand, 12.5" wide 708118 JMB-UMB Universal Mobile Base
39
17.0 Optional accessories
These items are purchased separately.
JET Tools JJP-12 Reviews
We have not received any reviews for JET Tools yet.