3Com 3CRWE876075 Support and Manuals
Get Help and Manuals for this 3Com item
View All Support Options Below
Free 3Com 3CRWE876075 manuals!
Problems with 3Com 3CRWE876075?
Ask a Question
Free 3Com 3CRWE876075 manuals!
Problems with 3Com 3CRWE876075?
Ask a Question
Popular 3Com 3CRWE876075 Manual Pages
User Guide - Page 4
... Only 3-4 Using the Setup Wizard 3-4
4 System Configuration
Advanced Setup 4-2
System Identification 4-4
TCP / IP Settings 4-5 RADIUS 4-8 Authentication 4-9 Filter Control 4-14
VLAN 4-16 SNMP 4-18
Configuring SNMP and Trap Message Parameters Configuring SNMPv3 Users 4-21
4-18
Administration 4-22
Changing the Password 4-22 Telnet and SSH Settings 4-23 Upgrading Firmware 4-24 WDS and Spanning...
User Guide - Page 9
... and bandwidth needs within the same area. Now with 3Com's enterprise-class wireless access point, you can build a cost-effective, reliable, secure wireless network that supports 802.11g, 802.11a, and 802.11b wireless users on a single access point. 1 INTRODUCTION
The 3Com® Wireless 8760 Dual-radio 11a/b/g PoE Access Point offers a dual-mode architecture that provides users with seamless...
User Guide - Page 11
... university staff members, while the second service provides open access to -multipoint link, or a multilayer topology.
1-3 WDS Bridging and Spanning Tree Protocol (STP) Support
A Distribution System (DS) is restricted or cost-prohibitive by linking several wireless access points together with its own security settings. For example, in a university network, an access point (AP) could be used in...
User Guide - Page 18
... detachable antennas that when this device is operational, the minimal body-to-antenna distance is installed in a hard-to-reach location.
CHAPTER 2: INSTALLING THE ACCESS POINT
Configuring a wireless LAN can be sure to allow for routing the antenna cable as placing a 3Com Wireless Access Point in a central area and making the necessary connections to the AP and the clients...
User Guide - Page 32
... security set. Choose your country. Unless it detects a DHCP server on the network, the access point uses Auto IP to wireless clients. Follow the instructions below to the Web interface: 1 Username, type admin (case sensitive). 2 Password, type password 3 Click Log On. To log on the Setup Wizard for initial configuration.
The access point can be asked to locate 3Com Wireless...
User Guide - Page 41
... configuration steps described in Chapter 4 to set . Unless it detects a DHCP server on Advanced Setup. The following page will display.
4-1 Use the 3Com Wireless Infrastructure Device Manager to launch the configuration Web interface. When installing the device manager, make sure the computer is set up an IP address for the access point. Enter the configured IP address of...
User Guide - Page 43
... for each VAP interface
Enables each virtual access point (VAP) interface, sets the Service Set Identifier (SSID), and configures wireless security
Configures the IEEE 802.11g interface
Configures common radio signal parameters and other settings for management access; Advanced Setup
Menu SNMP Administration
WDS/STP Settings Syslog Set-up Status AP Status Station Status Event Logs 802.11a...
User Guide - Page 58
... information over the network.
A defined set of the MIB specifications and the protocol used to and from wireless clients. These objects are sent to specified user targets.
Access to access this information using SNMP v1 and v2c is compliant with MIB II. CONFIGURING SNMP AND TRAP MESSAGE PARAMETERS
The access point SNMP agent must be enabled and...
User Guide - Page 64
...run the software it was using before the upgrade started. Until a reboot occurs, the access point will continue to the factory default settings when first activated after a reboot.
4-24 After upgrading new software, you must reboot the access point to implement the new code. Default: 22)
UPGRADING FIRMWARE
You can upgrade new access point software from a local file on the management workstation...
User Guide - Page 98
...access point. 2: Select TKIP when any WPA clients do not support AES. In mixed mode, the unicast encryption cipher (TKIP or AES-CCMP) is authenticated to a wireless network it has to enable all clients support... for networks moving from an access point and then returns, re-authentication is used for WPA are summarized below:
Table 7 WPA Configuration Settings
WPA and WPA2 pre-shared ...
User Guide - Page 117
... (no prompt
string -
Use the no form to use for units sold in other countries
Command Mode
Exec
Command Usage
• If you purchased an access point outside of the United States, the country code must be set ) - Example
Enterprise AP#country tw Enterprise AP#
prompt This command customizes the CLI prompt.
User Guide - Page 119
Password for management access. (Length: 3-16 characters, case sensitive) Default Setting null Command Mode Global Configuration Example
Enterprise AP(config)#password Enterprise AP(config)#
ip ssh-server enable This command enables the Secure Shell server. Syntax
password no form to reset the default password. Use the no password
password - Remember to disable the server. Syntax
ip ssh-...
User Guide - Page 170
...(config)#radius-server port-accounting 1813 Enterprise AP(config)#
radius-server timeout-interim This command sets the interval between transmitting accounting updates. (Range: 60-86400)
Default Setting 3600
Command Mode Global Configuration
Command Usage • The access point sends periodic accounting updates after every interim period until the user logs off and a "stop" message is sent...
User Guide - Page 239
... (MIC) is part of the Temporal Key Integrity Protocol (TKIP) encryption used in the network, wireless clients must be improved by selecting the best method for the specific deployment.
• Using the "hardware" option provides best performance when the number of operation and support for each transmitted packet and this can be upgraded to calculate...
User Guide - Page 256
The IP address you select the access point in the Wireless Network Tree. Review access point firmware revisions and update firmware if necessary. Make sure that all access points and wireless devices in the ESS in the Wireless Network Tree and click Properties. Make sure that security settings on the access point match those on a computer connected to the old IP address...
3Com 3CRWE876075 Reviews
We have not received any reviews for 3Com yet.