BenQ CP220 - XGA DLP Projector Support and Manuals
Most Recent BenQ CP220 Questions
BenQ CP220 Videos
Popular BenQ CP220 Manual Pages
User Manual - Page 2
...of Texas Instruments. Others are trademarks of BenQ Corporation. Copyright
Copyright 2006 by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without obligation to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any person of such revision or changes.
*DLP, Digital Micromirror Device and DMD are copyrights of...
User Manual - Page 7
... 240 volts AC, but could cause the objects to become heated and deformed or even cause a fire.
Important safety instructions
Your BenQ projector is designed and tested to meet the latest standards for future reference. Please read this manual and marked on the product. projector lamp is
2.
In areas where the
mains voltage may damage your...
User Manual - Page 10
Safety Instructions (Continued)
15. Doing so may result in damage. When the projector is securely installed.
19. Do not store the projector on the
vertically.
Use only BenQ's Ceiling Mount Kit for ceiling mount
installation.
Do not place liquids near or on end
17. Do not step on the projector or place
any objects upon it from its...
User Manual - Page 11
... conditions, selected input source contrast/brightness settings, and is directly proportional to deliver high reliability and ease of the projected image will decline over time and may vary within the lamp manufacturers specifications. This is normal and expected behavior.
Introduction 5 Introduction
Projector features
The projector integrates high-performance optical engine projection and...
User Manual - Page 14
... the displayed
temperature becomes too high.
Power (See "Start up or flashes if the projector's
picture timings for details.)
Exits and saves the menu settings.
Keystone / Right
When the on-screen menu is selected, there are several picture
5
6 7
10
setup options available.
11 6
9. Correct keystoning at the top or bottom of the projected...
User Manual - Page 15
... the screen image. Power (See "Start up /
3
10
down the projector" on page 30 for details.)
When the on page 25
1
for details.)
10.
for details.)
7
Manually corrects distorted images
2
resulting from an angled projection.
7. BLANK (See "Hiding the image" on the remote control to make
adjustments.
5. To release the function,
any key...
User Manual - Page 17
... behind the screen. If you use of the screen. BenQ recommends that you intend to position the projector for ceiling mounting of the projector
We want you to be installed in front of the wrong gauge or length screws. Positioning your equipment.
1. Safety instructions for quick setup and portability.
2. Floor in the Advance > Mirror menu after...
User Manual - Page 18
...projector position based upon a 16:9 projection if you will need to account for your projector. The projector... caused by this projector. The modern digital projector does not project directly...projector can be vertically offset from the horizontal edge of the projected image. BenQ has provided a table of the projector is positioned further away from the projector lens to the projector...
User Manual - Page 24
... Video source device:
1. Once connected, the audio can be like that shown in the following standards are supported:
• 480i • 576i • 720p (50/ 60 Hz)
• 480p • 576p...turned on page 17 for details. The final connection path should be controlled by the projector volume and mute settings. Take the (optional accessory) Component Video to VGA (D-Sub) adaptor cable and ...
User Manual - Page 28
..., press AUTO to select a number for the first
Password Setup
time, a prompt will be set -up is activated for each digit of the following 3 steps. i. ii.
Setting a password
CAUTION: Once a password has been set -up and return to the on the projector or remote control.
2. Open the on the screen. Use
Enter Password 0 0 0 0 Press Auto to Confirm
the Left or Right...
User Manual - Page 29
... not have to verify that it is incorrect, a "Password Error" message displays. The input type affects the options available for 3 seconds after opening the on- See "Selecting an application mode" on to
Setting > Password after each button press. Seek help from the local BenQ service center to
Setting > Change Password.
2. Open the on-screen menu and go on...
User Manual - Page 33
... pressing Left/ Right on the projector or remote control. You can manually adjust some of light output on the image you see the center of the projected image is a normal behavior because the projector doesn't carry brightness evenly throughout the image it projects, which causes an uneven distribution of the settings through the OSD menus...
User Manual - Page 39
... color intensity of the image. When a Video or S-Video signal is connected, the function is set -up to manually correct the image shape. Unavailable adjustments are provided so you can optimize your
Mode
projector image set to On, the projector will not need to suit your program type. Color (depends
on page 27 for details...
User Manual - Page 48
...Power Temp Lamp
Power events
O -
- Stand-by mode.
The projector has shutdown automatically. the projector, it ...problems.
1. The internal temperature is flashing during powering up. The Power indicator light is too high. 2. The projector needs 90 seconds to cool for 90 seconds after the
power is warning you try to "Indicators" on , it is turned off and contact qualified service...
User Manual - Page 54
... have other information, please visit support.BenQ.com.
48 Warranty In the event this product against any defects in accordance with any defective parts (labor included). Important: The above warranty shall be replacement of any defects. Warranty
Limited Warranty
BenQ warrants this product is found to country. To obtain warranty service, immediately notify the dealer from...
BenQ CP220 Reviews
Do you have an experience with the BenQ CP220 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for BenQ yet.
Earn 750 points for your review!