Black & Decker GH710 Support and Manuals
Get Help and Manuals for this Black & Decker item
View All Support Options Below
Free Black & Decker GH710 manuals!
Problems with Black & Decker GH710?
Ask a Question
Free Black & Decker GH710 manuals!
Problems with Black & Decker GH710?
Ask a Question
Most Recent Black & Decker GH710 Questions
I Need Parts For A Gh710 Trimmer.the Bearing Housing And The Needle Bearing
(Posted by anglaruba 10 months ago)
Is The Bushing/bearing At The Top Of The Motor Shaft, Above The Brushes Availabl
(Posted by jcash1238 3 years ago)
Popular Black & Decker GH710 Manual Pages
Type 1 Manual - GH710 - Page 1
....com/NewOwner
to register your Black & Decker purchase, go to speak with your new product.
Please have the catalog number available when you canʼt find the answer or do not have a question or experience a problem with an agent. GH710
TRIMMER / EDGER INSTRUCTION MANUAL
Model Number GH710
Thank you have access to 5 p.m. if not, the motor will not function properly...
Type 1 Manual - GH710 - Page 2
...manual. The tool and guard are used as wall, steps, large stone, tree, etc. Components 5 Assembly / Adjustment 5
Read All Instructions
Operating Instructions 7 Replacement Accessories 9 Maintenance 10 Troubleshooting 11 Service...not avoided, may result in moving parts. TABLE OF CONTENTS
Safety Guidelines -... contain long hair. • NYLON LINE - Use care when trimming around screens...
Type 1 Manual - GH710 - Page 3
...part that can not be controlled with the switch trigger is damaged should be properly repaired or replaced...line or one protected by an authorized service center unless otherwise indicated elsewhere in this manual. Keep cord from rotating line. Motors in maintenance section. Do not operate this tool for any damage repaired before further use .
SAVE THESE INSTRUCTIONS... or spool. •...
Type 1 Manual - GH710 - Page 4
... outdoor use of California to install the proper wall outlet. The smaller the gauge number, the heavier the cord. If the extension will cause a drop in line voltage resulting in good condition.... Minimum Gauge for Cord Sets
Volts 120V
Total Length of a polarized wall outlet. The label on cord length and nameplate ampere rating. SAFETY WARNINGS AND INSTRUCTIONS: POLARIZED PLUGS
To reduce ...
Type 1 Manual - GH710 - Page 5
... 9. NEVER OPERATE TOOL WITHOUT GUARD FIRMLY IN PLACE. Switch 4
2. Motor Housing
7. Cord Receptacle
4. Edge Guide
8. Cord Retainer
3. THE GUARD MUST ALWAYS BE ON THE TOOL TO PROTECT THE USER.
• Turn the trimmer upside B 2
down so that you hear it onto the
3
motor housing (3). Spool
7 9
6 8
1 2
3
ASSEMBLY AND ADJUSTMENT
ASSEMBLY TOOLS REQUIRED (NOT SUPPLIED...
Type 1 Manual - GH710 - Page 6
... housing
straight up or
shown in figure E (with the
E
Black & Decker logo facing
upward). ATTACHING THE AUXILIARY HANDLE
• Push the handle completely onto the housing
F
• To attach the handle, press in figure G.
6 HEIGHT ADJUSTMENT
G
• The overall height of the
trimmer can be
adjusted so that it in the direction of...
Type 1 Manual - GH710 - Page 7
... to 10° as barbs at the base of the line.
Pull the guide out until it snaps securely into the
plug blades (12) in the trimmer.
J
J1
5O-10O
7
Hook
the loop formed by doubling the
cord over the tab (11). OPERATING INSTRUCTIONS
WARNING: Always use proper eye protection that conforms
to insure...
Type 1 Manual - GH710 - Page 8
.... To acheive this is the best cutting area. • The trimmer cuts when passing the unit from the motor housing until tight.
9
HELPFUL CUTTING TIPS • Use the tip...trimmer as shown in figure J2. Stone and brick walls, curbs, and wood may wear string rapidly. • Do not allow spool cap to the original
position, out of the way. Use edge guide along such things as shown in part...
Type 1 Manual - GH710 - Page 9
...
weeds are available through Black & Decker service centers.
The line should
h
protrude approximately 5-3/8
inches (136mm) from the spool and housing.
DF-065. The line should protrude
approximately 5-3/8 inches
(136mm) from the spool housing (c) in the trimmer head (figure M). • Replace spool with Black & Decker model # DF-065. • Grasp empty spool (d) with one hand...
Type 1 Manual - GH710 - Page 10
... tangled more frequently than Black
& Decker factory wound spools. To rewind spools, follow the steps below:
• Unplug the tool.
• Remove the empty spool from the tool
as described in "REPLACING THE SPOOL".
• First wind new line onto the uppermost part of
the spool.
• Feed 3/4 inch (19mm) of
P
cutting line into one side
of the spool as described in...
Type 1 Manual - GH710 - Page 11
... issue. If damaged, replace spool. •Read the code on the back of the line (5.25 inches (133.4mm) from the spool.
If the automatic line feed still does not work or the spool is fed when the line shortens to approximately 3 inches (76.2mm). TROUBLE SHOOTING GUIDE
PROBLEM
Tool runs slowly. Automatic line feed does not feed more line. If it on...
Type 1 Manual - GH710 - Page 12
...
Line unravels when cap or spool is a participating retailer). This warranty gives you specific legal rights and you may be replaced or repaired at our option. FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are beyond the time set for exchanges. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker...
Type 1 Manual - GH710 - Page 13
Towson, MD 21286 U.S.A. Yellow Pages -
for Service & Sales
13 Joppa Rd. Imported by Black & Decker (U.S.) Inc.,
701 E. See 'Tools-Electric' -
Black & Decker GH710 Reviews
We have not received any reviews for Black & Decker yet.