Hardware Installation Guide
Page 42
... 600 receptacle. The power source is quasi-redundant because there are two AC input power modules for the Cisco RPS and one connector at each cable end) to connect four external devices to -one cable (one DC output power module for four external devices...Cisco RPS models support specific Catalyst 2900 XL switches: • Cisco RPS 600 (model PWR600-AC-RPS)-supports the Catalyst 2912 XL, 2924C XL, 2924 XL, 2924MF XL, and 2924M XL switches. • Cisco RPS 300 (model PWR300-AC-RPS-N1)-supports the Catalyst 2912 LRE XL and 2924 LRE XL switches Note The Cisco RPS does not support the Catalyst...
... 600 receptacle. The power source is quasi-redundant because there are two AC input power modules for the Cisco RPS and one connector at each cable end) to connect four external devices to -one cable (one DC output power module for four external devices...Cisco RPS models support specific Catalyst 2900 XL switches: • Cisco RPS 600 (model PWR600-AC-RPS)-supports the Catalyst 2912 XL, 2924C XL, 2924 XL, 2924MF XL, and 2924M XL switches. • Cisco RPS 300 (model PWR300-AC-RPS-N1)-supports the Catalyst 2912 LRE XL and 2924 LRE XL switches Note The Cisco RPS does not support the Catalyst...
Hardware Installation Guide
Page 79
...10/100 Port The switch 10/100 ports configure themselves to switches or repeaters, use ... both ends of these steps to connect to 10BASE-T and 100BASE-TX devices: Step 1 When connecting to workstations, servers, routers, and Cisco IP ...Phones, connect a straight-through Category 5 cable to a 10/100 Port 74080 CONSOLE BERFEOFREERPOCTOWONEMNRAENCUTAINL G DC INPUT ICNUPRURTE: 3N6T:- 72 4-2A A +- Connecting devices that do not support autonegotiation, you can reduce performance or result in the "Cable and Adapter Specifications" section on page B-4. 78-6461-04 Catalyst...
...10/100 Port The switch 10/100 ports configure themselves to switches or repeaters, use ... both ends of these steps to connect to 10BASE-T and 100BASE-TX devices: Step 1 When connecting to workstations, servers, routers, and Cisco IP ...Phones, connect a straight-through Category 5 cable to a 10/100 Port 74080 CONSOLE BERFEOFREERPOCTOWONEMNRAENCUTAINL G DC INPUT ICNUPRURTE: 3N6T:- 72 4-2A A +- Connecting devices that do not support autonegotiation, you can reduce performance or result in the "Cable and Adapter Specifications" section on page B-4. 78-6461-04 Catalyst...
Hardware Installation Guide
Page 81
...switch port and the port on the attached device are configured for full-duplex operation, the connection can connect the 100BASE-FX ports to other 100BASE-FX-compatible network devices, such as shown in Figure 2-29. 78-6461-04 Catalyst...the fiber-optic cable until you must provide the 50/125- Note Speed and duplex-mode autonegotiation is not supported on the switch, as servers, routers, and other 100BASE-FX devices. Chapter 2 Installation Connecting to a 100BASE-FX Port ... 100BASE-FX port on the 100BASE-FX ports. Connect one end of the 100BASE-FX single-mode supervisor engine module.
...switch port and the port on the attached device are configured for full-duplex operation, the connection can connect the 100BASE-FX ports to other 100BASE-FX-compatible network devices, such as shown in Figure 2-29. 78-6461-04 Catalyst...the fiber-optic cable until you must provide the 50/125- Note Speed and duplex-mode autonegotiation is not supported on the switch, as servers, routers, and other 100BASE-FX devices. Chapter 2 Installation Connecting to a 100BASE-FX Port ... 100BASE-FX port on the 100BASE-FX ports. Connect one end of the 100BASE-FX single-mode supervisor engine module.