Planning Guides
Page 1
... surface 4" (10.2 cm) chassis height 21" (53.3 cm) 19 1/2" * (49.5 cm) 33 1/2" * (85.1 cm) * including embosses in side of chassis 46" (116.8 cm) Product dimensions model sgm365 4" (10.2 cm) chassis height 1 5/8" (4.1 cm) bottom of base to cooking surface 21" (53.3 cm) 19 1/2" *... All tolerances ±1/16" (±1.6 mm), unless otherwise noted. www.Dacor.com 44 5/8" * (113.3 cm) Product dimensions model sgm466 Phone: (800) 7934-0.5093 Document # PG04-004 SGM304, SGM365, SGM466 30", 36", 46" Wide, Drop-in side of chassis Specifications subject to change without notice....
... surface 4" (10.2 cm) chassis height 21" (53.3 cm) 19 1/2" * (49.5 cm) 33 1/2" * (85.1 cm) * including embosses in side of chassis 46" (116.8 cm) Product dimensions model sgm365 4" (10.2 cm) chassis height 1 5/8" (4.1 cm) bottom of base to cooking surface 21" (53.3 cm) 19 1/2" *... All tolerances ±1/16" (±1.6 mm), unless otherwise noted. www.Dacor.com 44 5/8" * (113.3 cm) Product dimensions model sgm466 Phone: (800) 7934-0.5093 Document # PG04-004 SGM304, SGM365, SGM466 30", 36", 46" Wide, Drop-in side of chassis Specifications subject to change without notice....
Planning Guides
Page 2
...pressure** 5" Water column 11" Water column Max. SGM304 SGM365 SGM466 SGM304LP SGM365LP SGM466LP Gas type Natural LPG Manifold pressure 4" Water column 10" Water column Min. SGM304, SGM365, SGM466 Document # PG04-004 30", 36", 46" Wide, Gas Cooktops Revised 01/27/11 Page 2/5 PLANNING ...GUIDE Electrical Requirements WARNING To prevent an electric shock hazard, the power supply must meet the specifications stated below ). www.Dacor.com Phone: (800) 7934...
...pressure** 5" Water column 11" Water column Max. SGM304 SGM365 SGM466 SGM304LP SGM365LP SGM466LP Gas type Natural LPG Manifold pressure 4" Water column 10" Water column Min. SGM304, SGM365, SGM466 Document # PG04-004 30", 36", 46" Wide, Gas Cooktops Revised 01/27/11 Page 2/5 PLANNING ...GUIDE Electrical Requirements WARNING To prevent an electric shock hazard, the power supply must meet the specifications stated below ). www.Dacor.com Phone: (800) 7934...
Planning Guides
Page 3
...in place. clearance to combustible B surfaces Under Cabinet Clearances Model (B) Minimum* SGM304 29" (73.7 cm) SGM365 35 ¼" (89.5 cm) SGM466 46" (116.8 cm) * To allow access to the utilities and cooktop bottom, a fixed shelf should be placed away from drafts that may result ... the location where the cooktop will be installed. Raised Vent Compatibility If installing the cooktop with a raised vent, install only the approved Dacor model numbers specified below , allow for the routing of gas and electrical service behind it is installed. See the following : ◊...
...in place. clearance to combustible B surfaces Under Cabinet Clearances Model (B) Minimum* SGM304 29" (73.7 cm) SGM365 35 ¼" (89.5 cm) SGM466 46" (116.8 cm) * To allow access to the utilities and cooktop bottom, a fixed shelf should be placed away from drafts that may result ... the location where the cooktop will be installed. Raised Vent Compatibility If installing the cooktop with a raised vent, install only the approved Dacor model numbers specified below , allow for the routing of gas and electrical service behind it is installed. See the following : ◊...
Planning Guides
Page 4
...to determine proper fit Floor Side View - Carefully double check all dimensions against the table below and the correct diagram before cutting the countertop. www.Dacor.com Phone: (800) 7934-0.8093 Countertop Dimensions Installation Type Cutout Diagram (C) Min. (D) (E) (F) SGM304 without raised vent Figure 1 (Square)...the installation type. sgm Series Cooktop with CABP3 blower installed Floor Side View - Document # PG04-004 SGM304, SGM365, SGM466 30", 36", 46" Wide, Gas Cooktops Revised 01/27/11 Page 4/5 PLANNING GUIDE Cutout Dimensions Cutout tolerances +1/16" (+1.6 mm), ...
...to determine proper fit Floor Side View - Carefully double check all dimensions against the table below and the correct diagram before cutting the countertop. www.Dacor.com Phone: (800) 7934-0.8093 Countertop Dimensions Installation Type Cutout Diagram (C) Min. (D) (E) (F) SGM304 without raised vent Figure 1 (Square)...the installation type. sgm Series Cooktop with CABP3 blower installed Floor Side View - Document # PG04-004 SGM304, SGM365, SGM466 30", 36", 46" Wide, Gas Cooktops Revised 01/27/11 Page 4/5 PLANNING GUIDE Cutout Dimensions Cutout tolerances +1/16" (+1.6 mm), ...
Planning Guides
Page 5
... chassis H 7 1/2" (19.1 cm) min. from mounting surface to combustible side wall above countertop (both sides) 1 7/8" min. (4.8 cm) Figure 2 - www.Dacor.com Phone: (800) 7934-0.9093 Document # PG04-004 SGM304, SGM365, SGM466 30", 36", 46" Wide, Gas Cooktops Cutout tolerances +1/16" (+1.6 mm), -0, unless otherwise noted Rear wall Revised 01/27/11 Page 5/5 PLANNING GUIDE...
... chassis H 7 1/2" (19.1 cm) min. from mounting surface to combustible side wall above countertop (both sides) 1 7/8" min. (4.8 cm) Figure 2 - www.Dacor.com Phone: (800) 7934-0.9093 Document # PG04-004 SGM304, SGM365, SGM466 30", 36", 46" Wide, Gas Cooktops Cutout tolerances +1/16" (+1.6 mm), -0, unless otherwise noted Rear wall Revised 01/27/11 Page 5/5 PLANNING GUIDE...
Installation Instructions
Page 5
...) bottom of base to cooking surface 4" (10.2 cm) chassis height 21" (53.3 cm) 19 1/2" * (49.5 cm) 33 1/2" * (85.1 cm) * including embosses in side of chassis 46" (116.8 cm) Model SGM365 4" (10.2 cm) chassis height 1 5/8" (4.1 cm) bottom of base to cooking surface 21" (53.3 cm) 19 1/2" * (49.5 cm) * including embosses/screws in...
...) bottom of base to cooking surface 4" (10.2 cm) chassis height 21" (53.3 cm) 19 1/2" * (49.5 cm) 33 1/2" * (85.1 cm) * including embosses in side of chassis 46" (116.8 cm) Model SGM365 4" (10.2 cm) chassis height 1 5/8" (4.1 cm) bottom of base to cooking surface 21" (53.3 cm) 19 1/2" * (49.5 cm) * including embosses/screws in...
Installation Instructions
Page 7
clearance to combustible B surfaces Under Cabinet Clearances Model B: Minimum* SGM304 SGM365 SGM466 29" (73.7 cm) 35 1/4" (89.5 cm) 46" (116.8 cm) * To allow access to the utilities and cooktop bottom, a fixed shelf should be caused by reaching over a hot ... caused by doors, windows and heating and air conditioning outlets. • This appliance is to be used in conjunction with a suitable vent hood or approved Dacor raised vent system. All tolerances +1/16" (+1.6 mm), -0 unless otherwise noted. Allow 7 1/2" (19.1 cm) from edge of cutout. Minimum Required Clearances...
clearance to combustible B surfaces Under Cabinet Clearances Model B: Minimum* SGM304 SGM365 SGM466 29" (73.7 cm) 35 1/4" (89.5 cm) 46" (116.8 cm) * To allow access to the utilities and cooktop bottom, a fixed shelf should be caused by reaching over a hot ... caused by doors, windows and heating and air conditioning outlets. • This appliance is to be used in conjunction with a suitable vent hood or approved Dacor raised vent system. All tolerances +1/16" (+1.6 mm), -0 unless otherwise noted. Allow 7 1/2" (19.1 cm) from edge of cutout. Minimum Required Clearances...