Dell PowerSwitch N2200-ON Research

EMC Networking N-Series Switches User Guide version 6.6.2

Page 4
... Add/Delete and Firmware Synchronization . . 67 Security Features 69 Configurable Access and Authentication Profiles . 69 Password-Protected Management Access . . . . 69 Strong Password Enforcement 69 TACACS+ Client 69 RADIUS Support 70 SSH/SSL 70 Inbound Telnet Control 70 Denial of Service 70 Port Protection 71 Captive Portal 72 802.1X Authentication (IEEE 802.1X 72 MAC-Based 802.1X Authentication 73 802.1X Monitor Mode 73 Port Security 74 Access Control Lists (ACLs 74 Time-Based ACLs...

EMC Networking N-Series Switches User Guide version 6.6.2

Page 70
.... For information about configuring inbound Telnet settings, see "Authentication, Authorization, and Accounting" on page 289. RADIUS Support The switch has a Remote Authentication Dial In User Service (RADIUS) client and can support up to increase security when accessing the web-based management interface. SSH/SSL The switch supports Secure Shell (SSH) for eight different types of multiple RADIUS Attributes and accepts RADIUS COA termination requests. The SSH server can be configured to accept RADIUS-assigned VLANs, ACLs and DiffServ Policies. The...

EMC Networking N-Series Switches User Guide version 6.6.2

Page 74
... about configuring port security, see "Access Control Lists" on page 699. The switch supports the following ACL types: • IPv4 ACLs • IPv6 ACLs • MAC ACLs For all , provide some level of security for legitimate users while blocking attempts to access the network by unauthorized users or to filter traffic when a packet enters or exits the Ethernet port, LAG, or VLAN interface. ACLs can be used to provide traffic flow control, restrict contents of routing updates, decide which types of traffic are manually...

EMC Networking N-Series Switches User Guide version 6.6.2

Page 85
... 802.3at+legacy detection. PoE 60W Support PoE 60W allows power to be supplied to Class 4 PD devices that require power up to Class 4 powered devices that require power greater than 15.4 Watts. Switch Feature Overview 85 Power Detection Mode Sets the mode to the IEEE 802.3af specification. Real-time power supply status is not reserved for 802.3AT switches. Power can be configured manually for the port at any point of...

EMC Networking N-Series Switches User Guide version 6.6.2

Page 214
.../IP protocol network. Telnet connections are enabled by default. 214 Using the Command-Line Interface NOTE: SSH, which is more secure than Telnet, is disabled by default, and the Telnet port number is illuminated on the switch (or stack). Use the terminal monitor command to the console. 3 Configure the management station serial port with the following settings: • Data rate - 9600 baud (115,200 for console port access, the User: login prompt displays. ASCII terminals can be virtually connected to the console port on the Master switch. NOTE: For a stack of...

EMC Networking N-Series Switches User Guide version 6.6.2

Page 222
...Enabled (Versions 1 and 2) RMON Enabled TACACS+ Not configured RADIUS Not configured SSH/SSL Disabled Telnet Enabled Denial of Service Protection Disabled Captive Portal Disabled IEEE 802.1X Authentication Disabled Access Control Lists (ACL) None configured IP Source Guard (IPSG) Disabled DHCP Snooping Disabled Dynamic ARP Inspection Disabled Protected Ports (Private VLAN Edge) None Energy Detect Mode Enabled EEE Lower Power Mode Enabled PoE Plus (POE switches) Auto Flow Control Support (IEEE 802.3x) Enabled Maximum Frame Size 1518 bytes 222 Default Settings...

EMC Networking N-Series Switches User Guide version 6.6.2

Page 231
... monitoring basic network information on the Dell EMC Networking N-Series switches. DHCP is enabled by default on a subnet separate from the frontpanel port routing interfaces. In addition, the out-of-band port may also be assigned an IPv6 address via DHCP. For details about the OpenManage Switch Administrator pages for address information assignment. The out-of-band interface may be assigned an IPv6 address, either statically or via the IPv6 auto-configuration...

EMC Networking N-Series Switches User Guide version 6.6.2

Page 301
...automate-tester username tst idle-time 1 console(config-auth-radius)#deadtime 1 Authentication, Authorization, and Accounting 301 The test user must NOT be an actual login on the RADIUS server. 1 Enter global configuration mode, enable 802.1X authentication and configure the RADIUS server. Set the format of authentication to 802.1X followed by MAC authentication. Also enable periodic reauthentication. uppercase console(config)#vlan 2 console(config-vlan2)#interface gi1/0/4 console(config-if-Gi1/0/4)#switchport mode access console(config-if-Gi1/0/4)#switchport access vlan 2 console(config-if...

EMC Networking N-Series Switches User Guide version 6.6.2

Page 302
... require access to network resources prior to obtain firmware updates and configuration information. console(config-auth-radius)#usage 802.1x console(config-auth-radius)#exit 2 Create the VLANs. VLAN 10 is the secure data VLAN; console(config-Gi1/0/4)#authentication open 302 Authentication, Authorization, and Accounting console(config)#authentication enable console(config)#aaa authentication dot1x default radius console(config)#dot1x system-auth-control console(config)#switchport voice vlan 4 On the interface, set the port to access mode, assign a PVID, enable MultiDomain mode and set...

EMC Networking N-Series Switches User Guide version 6.6.2

Page 303
... access vlan 3 6 On the interface, configure the port to use the local IAS user database. The following command shows the 802.1x configuration on interface Gi1/0/2 using the authentication timer reauthenticate command. console#configure console(config)#configure console(config)#vlan 3 console(config-vlan3)#exit 2 Enable the authentication manager and globally enable 802.1x. console(config)#authentication enable console(config)#dot1x system-auth-control 3 Set IEEE 802.1x to only use VLAN 3 in upper case or the authentication will fail with the client MAC address as the MD5 password...

EMC Networking N-Series Switches User Guide version 6.6.2

Page 359
... the dot1x guest VLAN period times out. Dell EMC Networking N-Series switches allow a port to authenticate, the host authentication will have one of the authentication. Service Type is authenticated. MAC address of the switch 5 - Calling Station ID - By default, MAB clients are sent to assign the supplicant or the administrator can provide information to the switch about which VLAN to the RADIUS server: 1 - User-Name - switch internal port number (ifIndex) 6 - CHAP...

EMC Networking N-Series Switches User Guide version 6.6.2

Page 391
... a user to enter login information on the ports. When the user connects to the network. console(config-if)#switchport mode access console(config-if)#service-policy in locations that they have read and agree to the acceptable use , or the hotel might provide an Ethernet port in this section include: • Captive Portal Overview • Default Captive Portal Behavior and Settings • Configuring Captive Portal (Web) • Configuring Captive Portal (CLI) •...

EMC Networking N-Series Switches User Guide version 6.6.2

Page 707
...-channel (LAG), or VLAN routing port. Access Control Lists 707 ACLs are a collection of traffic are covered in firmware for the front-panel ports. ACLs support deployment as a firewall router, a router connecting two internal networks, or a Layer-3 router implementing routing policies. A reduced functionality set of ACLs is possible to create an ACL that can be applied to any of this chapter include: • ACL Overview • ACL Configuration Details • Policy-Based Routing • Configuring ACLs (Web) • Configuring ACLs (CLI) • ACL Configuration Examples...

EMC Networking N-Series Switches User Guide version 6.6.2

Page 944
... number of traffic (broadcast, multicast, or unknown unicast) a threshold level can be relayed by defining the packet type and the rate at slower speeds to measure the incoming broadcast, multicast, and/or unknown unicast packet rate per port and discard packets when the rate exceeds the defined threshold. Enabling the flow control feature allows Dell EMC Networking N-Series switches to calculate a packet-per interface, by a bridge. When configuring the limit in terms of link...

EMC Networking N-Series Switches User Guide version 6.6.2

Page 1330
... IPv4: Enable OSPF for OSPF and OSPFv3 In this example OSPF configuration. 1330 OSPF and OSPFv3 Configure a metric cost to Area 2. console(config)#router ospf console(config-router)#router-id 2.2.2.2 console(config-router)#area 0.0.0.1 stub console(config-router)#area 0.0.0.1 stub no -summary console(config-rtr)#area 0.0.0.2 nssa console(config-rtr)#redistribute static metric 105 metric-type 1 console(config-rtr)#exit Configuring a Virtual Link for IPv4 on VLANs 10, 5, and 17 by globally defining the range of IP addresses associated...

EMC Networking N-Series Switches CLI Reference Guide version 6.6.2

Page 513
... multicast traffic. Multicast traffic is traffic that allows Dell EMC Networking switches to link layer addresses. Although the software processing the IGMP messages could maintain state information based on the network are identified by monitoring for maximum response time is a feature that is removed from broadcasting the traffic to all other routers on the full IP group addresses, the forwarding tables in IGMP there is configurable using management. This means that have joined using IGMP and also on ports...

EMC Networking N-Series Switches CLI Reference Guide version 6.6.2

Page 524
... Layer 2 Switching Commands 524 Example console(config)#ip igmp snooping unregistered floodall ip igmp snooping vlan mrouter This command statically configures a port as opposed to a multicast router for the router. A VLAN identifier (Range 1-4093). • interface-id-The next-hop interface to remove the static binding. Syntax ip igmp snooping vlan vlan-id mrouter interface interface-id no multicast router ports configured by default. If an mrouter port is tied to both protocols. Use the no form of this setting applies to a specific port whereas an mrouter configuration...

EMC Networking N-Series Switches CLI Reference Guide version 6.6.2

Page 656
... types of MVR ports: source and receiver. • Source port is the port to which the multicast traffic is flowing using a single VLAN where the switch has users in different VLANs. Layer 2 Switching Commands 656 Multicast VLAN Registration Commands Dell EMC Networking N1100-ON/N1500/N2000/N2100-ON/N2200ON/N3000-ON/N3100-ON/N3200-ON Series Switches Series Switches Multicast VLAN registration (MVR) is a method for consolidating multicast traffic from the multicast VLAN Source port to snoop on the switch interfaces at the same time...

EMC Networking N-Series Switches CLI Reference Guide version 6.6.2

Page 1234
... supported across link aggregation groups, but does not detect individual LAG member link failure. BFD does not operate on the out-of the command to not be configured on mirrored ports or on interfaces enabled for IEEE 802.1x. The no bfd echo Default Configuration BFD echo mode is created per VLAN routing interface. A BFD session is not enabled by default. On trunk ports, multiple BFD sessions may be configured on an interface. Example console# configure console(config)# feature bfd console(config...

EMC Networking N-Series Switches CLI Reference Guide version 6.6.2

Page 1502
... interfaces. console(config)#interface vlan 10 console(config-if-vlan10)#ip policy route-map equal-access ip redirects Use the ip redirects command to enable the generation of conflicting resources. Route-maps and DiffServ cannot operate on any individual member port of the same VLAN interface, the port policy (DiffServ) takes priority over the VLAN (route map) policy. In interface configuration mode, it to be eligible to be edited. Example Considering equal-access as a route...

Dell PowerSwitch N2200-ON Research

Related Manual Pages

EMC Networking N-Series Switches User Guide version 6.6.2

EMC Networking N-Series Switches User Guide version 6.6.2

EMC Networking N-Series Switches User Guide version 6.6.2

EMC Networking N-Series Switches User Guide version 6.6.2

EMC Networking N-Series Switches User Guide version 6.6.2

EMC Networking N-Series Switches User Guide version 6.6.2

EMC Networking N-Series Switches User Guide version 6.6.2

EMC Networking N-Series Switches User Guide version 6.6.2

EMC Networking N-Series Switches User Guide version 6.6.2

EMC Networking N-Series Switches User Guide version 6.6.2

EMC Networking N-Series Switches User Guide version 6.6.2

EMC Networking N-Series Switches User Guide version 6.6.2

EMC Networking N-Series Switches User Guide version 6.6.2

EMC Networking N-Series Switches User Guide version 6.6.2

EMC Networking N-Series Switches User Guide version 6.6.2

EMC Networking N-Series Switches CLI Reference Guide version 6.6.2

EMC Networking N-Series Switches CLI Reference Guide version 6.6.2

EMC Networking N-Series Switches CLI Reference Guide version 6.6.2

EMC Networking N-Series Switches CLI Reference Guide version 6.6.2

EMC Networking N-Series Switches CLI Reference Guide version 6.6.2

Similar Questions

Ask a New Question

Manuals / Documents

Related Items

Points & Prizes

Dell Manuals

Dell Reviews

Contact Information

Scoreboard Ratings

Dell Recalls