Dewalt DW0165S Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DW0165S manuals!
Problems with Dewalt DW0165S?
Ask a Question
Free Dewalt DW0165S manuals!
Problems with Dewalt DW0165S?
Ask a Question
Popular Dewalt DW0165S Manual Pages
Instruction Manual - Page 1
HR E
ES
F
DW0165N, DW0165S, DW0330SN
PT
User Manual
E
PT
NL
DK
SE
FIN
NO
PL
GR
DW0165S
CZ
RU
HU
SK
SI
BG
RO
EE
LV
LT
www.DEWALT.com
TR
Please read these instructions before operating the product.
Instruction Manual - Page 10
...; Turning the Tool On • Choosing the Settings • Taking Measurements • Calibrating the Tool • Warranty • Error Codes • Specifications
Retain all users understand and adhere to these instructions.
Do not look into the beam with Part 15 of injury, user must read the Safety Instructions and Product Manual before using this device must ensure that may...
Instruction Manual - Page 12
... until you take a measurement. On the first screen...save your new setting.
Press
to save your setting. Pull up the endpiece on and display the red laser dot.
5. Setting Screen Brightness
By default, the tool's screen will be set at 25% ... or object, and not toward
and press . and + ends of each time you
manually turn off 90 seconds after 30 sec, 60 secs, 90 secs, or 300 secs....
Instruction Manual - Page 13
... the tool position setting (Figure C 4 ) is correct for taking the measurement.
4.
Adding 2 Measurements You can change the unit of measure to a wall or object (Figure F 3 ). Then repeat steps 4-6. On the Settings Menu (Figure G ), select ft/m and press .
4. To measure distances from the tripod connection on and display the red laser dot.
3. To take a new measurement, press to move...
Instruction Manual - Page 14
... Press
Figure A 3 ) to measure (Figure J 1 ).
7. Point the tool's laser (Figure A 1 ) toward a wall or object, and not toward the wall or object whose distance you need to turn the tool
on and display the red laser dot.
3. Make sure the tool position setting (Figure C 4 ) is correct for taking the measurement.
4. Point the tool's laser toward anyone 's eyes.
2.
Instruction Manual - Page 16
... Menu (Figure E 3 ).
• Press the arrow buttons to turn the tool
3. Make sure the tool position setting (Figure C 4 ) is correct for taking the measurement.
4. Point the tool's laser (Figure A 1 ) toward a wall or object, and not toward anyone 's eyes.
2. Measure the width of the first wall, floor, or object (Figure D 1 ).
• Position the tool at...
Instruction Manual - Page 17
... the tool
on the third line of the tool.)
• Press to display the height measurement on and display the red laser dot.
3. Make sure the tool position setting (Figure C 4 ) is correct for taking the measurement.
4.
Point the tool's laser (Figure A 1 ) toward E
a wall or object, and not toward anyone's eyes.
2. Adding/Subtracting 2 Volumes
You can...
Instruction Manual - Page 18
... the bottom of a tall object (e.g., a tall building), you need to 2 points on and display the red laser dot.
3. Make sure the tool position setting (Figure C 4 ) is correct for taking the measurement.
18 Distances to 2 Points
You can calculate the height based on the distance to 1 point or the distances from the bottom of...
Instruction Manual - Page 19
...top of the building or object (Figure Q 3 ).
8.
Press
to measure the distance.
5. Point the laser toward the bottom of the building or object whose height you need to the...height to turn the tool
on and display the red laser dot.
3.
Press
(Figure A 3 ) to be measured (Figure Q 1 ).
6. Make sure the tool position setting (Figure C 4 ) is blocked by other buildings ...
Instruction Manual - Page 20
... you are framing a wall, use the Stakeout feature to take the
10. Point the tool's laser (Figure A 1 ) toward a wall or object, and not toward anyone 's eyes.
2. Make sure the tool position setting
(Figure C 4 ) is set to to measure the height of the tool.
20 Press
to easily mark the position of your tripod (Figure...
Instruction Manual - Page 21
... screen is correct for example, 12". For each stud, for taking the measurement.
6. Make sure the tool position setting (Figure C 4 ) is set to the distance from the right edge of one stud to turn the tool
on and display the red laser dot.
3. Press and until the bottom number on the screen (Figure W 2 ).
11...
Instruction Manual - Page 22
... to the last 20 measurements are stored in the vertical or horizontal position on and display the red laser dot.
22 connection.
• Press .
4. APPLE AND THE APPLE LOGO ARE TRADEMARKS OF APPLE INC., REGISTERED IN THE U.S. APP STORE IS A SERVICE MARK OF APPLE INC., REGISTERED IN THE U.S. Using the DEWALT® Tool Connect...
Instruction Manual - Page 24
... Main Menu (Figure E 2 ).
4. This warranty gives you specific legal rights and you may have been made or attempted by normal use, for a full refund - In addition to the warranty, DEWALT® tools are covered by our:
1 YEAR FREE SERVICE
DEWALT will maintain the tool and replace worn parts caused by others. RECONDITIONED PRODUCT: Reconditioned product is...
Instruction Manual - Page 25
... occurs, return the defective device to the Warranty.
25
Measuring Time Too Long
102 Received Signal Too High
Target is too reflective. Allow the device to warm up to a temperature within the specified Operating Temperature Range.
Contact the Service Center or distributor. Error Codes
E
If INFO appears on /off several times. Use the target...
Instruction Manual - Page 26
... reflecting target surface, or large temperature fluctuations), the error can increase by to ± 0.003 in/ft...Laser Power
Class 2 ≤ 1mW @ 620-690nm or Class 3R ≤ 5mW @ 620-690nm
Laser Automatic Switch-off
30s
Unit Automatic Switch-off
By default, 90s. E Specifications
DW0165N & DW0165S
DW0330SN
Range
6in to 165ft (0.15m to 50m)
6in to 330ft (0.15m to 100m)
Measuring...
Dewalt DW0165S Reviews
We have not received any reviews for Dewalt yet.