Fender Mustang 1-5 V2 Advanced Support and Manuals
Get Help and Manuals for this Fender item
This item is in your list!
View All Support Options Below
Free Fender Mustang 1-5 V2 Advanced manuals!
Problems with Fender Mustang 1-5 V2 Advanced?
Ask a Question
Free Fender Mustang 1-5 V2 Advanced manuals!
Problems with Fender Mustang 1-5 V2 Advanced?
Ask a Question
Popular Fender Mustang 1-5 V2 Advanced Manual Pages
Owner Manual - Page 2
...to activate their actual settings when a preset is your step-by-step guide to scroll through each ...Mustang amplifier (except MASTER) is part of whichever knob was turned most recently is its ability to "8" but the stored VOLUME preset setting is based on the Mustang...for the Mustang III / IV / V (V.2) advanced manual. MOD
DLY/REV
2
fender.com Each preset includes the settings of all ...
Owner Manual - Page 3
...Repeats
B1
Small Room Reverb
B2
Plate Reverb
B3
Large Hall Reverb
C1
Fender '65 Spring Reverb
C2
Fender '63 Spring Reverb
C3 Tape Delay
Room
D1 Tape Delay
Large Hall
... within each knob. MUSTANG™ I/II (V.2)
These LEDs are selected simultaneously, the TAP button will blink green and only control the delay time setting.
♫ You can use TAP to set the TAP interval of...
Owner Manual - Page 4
...Mustang amplifier gives you the powerful ability to enjoy the Mustang's stereo features. This indicates that turns the control panel LEDs into your Mustang amplifier for 2 seconds. MUSTANG™ I/II (V.2)
Tuner Button
Your Mustang... cancel the save every setting on your
4
fender.com You can proceed to... of the programmable knobs, such as part of each knob, including effect selections...
Owner Manual - Page 5
...
Factory Restore & Firmware Update
Connect a (optional) 1-button footswitch (P/N 0994049000) into the FTSW jack to factory settings: 1. The LED (next to the FTSW jack) will be illuminated to proceed to the footswitch. To program the footswitch:
1. Now when you can restore your two favorite presets.
There's even a forum just for the Mustang: www.fender.com/community...
Owner Manual - Page 6
.../IV/V (V.2)
Advanced Manual
Introduction
This manual is your step-by-step guide to all the advanced features found on screen for each preset, the "programmable" knob postitions are located in the Guitar Signal Processing Path. Navigation
There are displayed on your Mustang I activate a programmable knob? Selecting Presets
Turn the DATA WHEEL to select one of Mustang navigation...
Owner Manual - Page 7
... Pitch Shifter
fender.com
7
Press the AMP button. 2.
Reverb effects
To select Effects:
1. Turn the DATA WHEEL to select one of 17 amplifier models:
AMP MODELS Studio Preamp ... MUSTANG™ III/IV/V (V.2)
Amplifier Menus
Select amplifier models and adjust amplifier settings using the Amp menus.
♫ You can de-select the highlighted amp setting and return to Amp Model selection...
Owner Manual - Page 8
... only control the delay time setting.
♫ You can have temporarily modified the preset. MUSTANG™ III/IV/V (V.2)
Effects...Settings
Use the Effects Settings menus to adjust a dazzling array of each knob, every effect setting, and the amp model selection, are in the effect settings menus, by turning the DATA WHEEL to "tap in ! Press and hold any other setting on the amplifier as part...
Owner Manual - Page 9
... equipment for the Mustang III) to perform the functions listed along with the MODE 2 LED). The TAP and EXIT buttons
will appear in line with a fine tuning needle.
fender.com
9 You can...2 and MODE 3.
When you should be a Quick Access preset in Tuner mode that are off. MUSTANG™ III/IV/V (V.2)
1. Turn the DATA WHEEL select a preset destination to exit from the Tuner...
Owner Manual - Page 10
... hard on your Mustang amplifier using the buttons labeled: STOMP / MOD / DELAY (in two modes, Volume behavior mode and Expression behavior mode. You must start the calibra-
10
fender.com To calibrate the... Volume behavior mode (green) is used to control master volume (or the EXP-1 can be set the range of pedal movement that is registered (recognized) by the amplifier.
♫ For example,...
Owner Manual - Page 11
... (Toe Volume).
• Pedal Initial Source - (From Preset/From Pedal) Select "From Preset" if you want to erase your Mustang amplifier using the included cable. 2.
fender.com
11 EXP-1 Pedal Settings
The EXP-1 pedals settings can be OFF when switched to Volume mode.
• Volume Mode Heel/Toe - (0-100%) Use these two menus to...
Owner Manual - Page 12
... . The Mustang IV & V amplifiers can then access those changes until Memory Lock is locked.
• Memory Lock - Use this information to adjust the contrast of connected sound equipment.
• LCD Contrast - Select "Normal" for accompaniment. Use the volume control on your effects device.
12
fender.com
This menu displays the Firmware version currently...
Owner Manual - Page 13
...illuminated.
! Factory Restore & Firmware Update
Factory Restore
You can restore your Mustang and music in general: • www.fender.com/support • Join a Fender Community forum where you can ...Mustang amplifier to the original factory settings if desired.
To restore the Mustang amplifier to the next level. MUSTANG™ III/IV/V (V.2)
USB Port
Use the USB port to connect the Mustang...
Owner Manual - Page 14
... de México, S. El Naranjo.
RFC: FVM-140508-CI0 Servicio al Cliente: 01(800) 7887395, 01(800) 7887396, 01(800) 7889433
Fender® and Mustang™ are property of FMIC. All rights reserved. de R.L. Calle Huerta #279, Int. de C.V. ENGLISH rev b C.P. 22785.
Other trademarks are trademarks of their respective owners. ...
Fender Mustang 1-5 V2 Advanced Reviews
Do you have an experience with the Fender Mustang 1-5 V2 Advanced that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Fender yet.
Earn 750 points for your review!