Fluke 393FC Support and Manuals
Fluke 393FC Videos
Popular Fluke 393FC Manual Pages
Product Manual - Page 1
All product names are subject to change without notice.
MyFlukeStore Shop for Fluke products online at: www.
.com 1.888.610.7664 All rights reserved. Specifications are trademarks of their respective companies. 393/393 FC
CAT III 1500V TRMS Clamp Meter
Users Manual
July 2021 (English) © 2021 Fluke Corporation.
Product Manual - Page 2
...support...warrants that software will be error free or operate without interruption. Following warranty repair, the product will operate ... of this warranty on behalf of repair/replacement parts when product purchased in one country ...service center within the warranty period. V.
Fluke does not warrant that service center, with its functional specifications for the repair...
Product Manual - Page 4
393/393 FC Users Manual
Maintenance ...17 How to Clean the Case 17 Environmental 17 Service ...18
Specifications ...18 General...18 Electrical ...18 Mechanical ...21 Environmental 22
ii
MyFlukeStore Shop for Fluke products online at: www.
.com 1.888.610.7664
Product Manual - Page 5
... to 1000 Aac with Fluke Connect™ (393 FC)
1
MyFlukeStore Shop for Fluke products online at: www.
.com 1.888.610.7664 The illustrations in this manual show the 393 FC.
Product Manual - Page 6
.... 393/393 FC Users Manual
A Warning identifies conditions and...Model Number varies TL1500DC i2500-18 iFlex TPAK80-4-8001 TPAK80-4-2002C 37x not shown
Description Clamp Meter 1500 V Test Lead Set... Flexible Current Probe 18 in (46 cm) Strap 9 in (23 cm) Magnet Carry Case Safety Information
Fluke Connect™ (393 FC)
Fluke Connect™ software (may not be available in all regions) supports...
Product Manual - Page 10
... a voltage >30 V or a voltage overload (OL)
Polarity indication
6
MyFlukeStore Shop for Fluke products online at: www.
.com 1.888.610.7664 393/393 FC Users Manual
Display
Table 3 is active Battery status
16
Item
Description
Min, Max, or Avg measurement indication
Zero indication
Continuity indication
AC...
Product Manual - Page 14
Turn the control knob to the test points of the circuit. If the resistance is 393/393 FC Users Manual
Resistance/Continuity
To measure resistance or continuity:
1. Touch the probes to D. 2. Remove power from the circuit to the VX terminal. 4. Connect the black test lead to the COM terminal and the red test lead to test. 3. The display shows the value.
Product Manual - Page 16
.... Note
When you close to O
5. 393/393 FC Users Manual
Amps AC
XW Warning
To prevent electrical shock, do not apply... waveforms. The flexible and lightweight measuring head allows quick and easy installation in hard-to O.
2. The display shows J to make the.... Position the Clamp jaw around the conductor. Connect the flexible part of the iFlex Probe around the conductor. If you open the...
Product Manual - Page 17
Figure 2. Flex Probe Setup
1
2
3
4
>2.5 cm >1 in
0.5 A
13
MyFlukeStore Shop for any damage.
• Check that the coupling system is in the correct position O.
CAT III 1500V TRMS Clamp Meter ...
Product Manual - Page 18
... will trigger the hold the display reading, push e. 393/393 FC Users Manual
Measurement Features
This section is about the Clamp features you can use the HOLD... and H. Push e >2 s to tell you measure resistance, continuity, capacitance, or a diode junction.
The display updates when the measured value: • exceeds the threshold value (voltage, capacitance, current, dc power) • is...
Product Manual - Page 19
... reading except for >2 s.
Push e to enter the Min/Max/Avg mode. Note
The Min/Max/Avg function does not support Auto Hold and Inrush Current/Peak Current. Push M to pause the
reading update (recording continues). Auto Hold Functions
Function V ac V dc mV dc Ohm Capacitance A dc A ac dc Power
Threshold 10 V 10...
Product Manual - Page 20
... Fluke Connect™ app enables you update the firmware. 3.
Dashes show simultaneously on your team. On the Clamp, push I for Clamps that occurs when an electrical device is set in the Product internal memory and to...393 FC)
See Power-On Options. 393/393 FC Users Manual
Inrush Current/Peak Current
Inrush Current is surge current that have the Fluke Connect™ feature.
Product Manual - Page 22
... optimum performance. 393/393 FC Users Manual
Service
An authorized Fluke Calibration service center should service the Product at two-year intervals to 75 %.
Accuracy specifications take the form of: ±([% of Reading] + [Number of the available replacement parts. Contact your equipment distributor or authorized Fluke Calibration Service Center for any Terminal and Earth Ground...
Fluke 393FC Reviews
Do you have an experience with the Fluke 393FC that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Fluke yet.
Earn 750 points for your review!