Fluke 9100S-B-156 Support and Manuals
Get Help and Manuals for this Fluke item
This item is in your list!
View All Support Options Below
Free Fluke 9100S-B-156 manuals!
Problems with Fluke 9100S-B-156?
Ask a Question
Free Fluke 9100S-B-156 manuals!
Problems with Fluke 9100S-B-156?
Ask a Question
Popular Fluke 9100S-B-156 Manual Pages
Manual - Page 2
... its functional specifications for damage in material and workmanship under normal use and service. Following warranty repair, the product will be error free or operate without notice. • Copyright © 2005 • Printed in Fluke's opinion, has been misused, altered, neglected, or damaged by accident or abnormal conditions of operation or handling. Warranty support is available...
Manual - Page 3
...Introduction 1 1.2 Symbols Used 1 1.3 Safety Information 3
1.3.1 Warnings...3 1.3.2 Cautions...4 1.4 Authorized Service Centers 5
2 Specifications and Environmental Conditions 9
2.1 Specifications 9 2.2 Environmental Conditions 9
3 Quick Start 11
3.1 Unpacking 11 3.2 Set-up...11 3.3 Power...11 3.4 Setting the Temperature 11
4 Parts and Controls 13
4.1 Rear Panel 13 4.2 Side View 14...
Manual - Page 4
9100S Dry-Well Calibrator
6.3.1 Scan Control 22 6.3.2 Scan Rate...22 6.4 Set-point Resistance 22 6.5 Secondary Menu 23 6.6 Heater Power 23 6.7 Proportional Band 23 6.8 Controller Configuration 24 6.9 Operating ...DELTA 38 9.2.2 Compute R0 and ALPHA 38 9.2.3 Accuracy and Repeatability 39
10 Maintenance 41
ii
MyFlukeStore Shop for Fluke products online at: www.
.com 1.877.766.5412
Manual - Page 9
...set , using the control buttons, to 707°F). Multiple fault protection devices insure user and instrument safety and protection.
The controller uses a precision platinum RTD as described in the instruction manual... You Start
Symbols Used
1.1 Introduction
The Fluke 9100S Mid-Range Field Calibrator may be used on the instrument or in this manual. This instrument is small enough to use...
Manual - Page 12
... at least 6 inches (15
4
MyFlukeStore Shop for Fluke products online at temperatures less than 50°C. Use ...installed correctly.
●● Always replace the power cord with an approved cord of the correct rating and type.
●● HIGH VOLTAGE is set...hazardous situation. if the instrument is set -point less than 100°C. 9100S Dry-Well Calibrator
Safety Information
BURN ...
Manual - Page 13
...Troubleshooting, on your Fluke product:
5
MyFlukeStore Shop for Fluke products online at: www.
.com 1.877.766.5412 Although it must have handle temperature limits. Power bumps from the factory set values. Before You Start
Authorized Service...as a handle for optimum durability and trouble free operation, it has been designed for carrying the instrument. Always handle these parameters is...
Manual - Page 14
9100S Dry-Well Calibrator
Authorized Service Centers
6
MyFlukeStore Shop for Fluke products online at: www.
.com 1.877.766.5412
Manual - Page 15
Before You Start
Authorized Service Centers
E-mail: antng@singa.fluke.com When contacting these Service Centers for support, please have the following information available:
●● Model Number ●● Serial Number ●● Voltage ●● Complete description of the problem
7
MyFlukeStore Shop for Fluke products online at: www.
.com 1.877.766.5412
Manual - Page 17
....1010.1 UL3111 and ANSI/ISA-S82.01 OVERVOLTAGE (Installation) CATEGORY II, Ploution Degree 2 per IEC1010-1
Sensor burnout protection, over-temperature cutout, and electrical fuses
250 V 3 A FF (very fast acting) NO USER SERVICEABLE PARTS
2.2 Environmental Conditions
Although the instrument has been designed for optimum durability and trouble-free operation, it must be operated in the...
Manual - Page 19
...Specifications, for safe and easy insertion and removal of the proper voltage, frequency, and current capability. The procedure is shipping damage, notify the carrier immediately. 3 Quick Start
Quick Start
Setting the Temperature
3.1 Unpacking
Unpack the dry-well carefully and inspect it Software and User's Guide
3.2 Set... 9930 Interface-it for Fluke products online at least...
Manual - Page 35
...the factory set the parameter to improve the accuracy of these constants and their settings with the instrument manual. The linefeed parameter is reached, press "SET" to set values.
The correct setting of the... parameters is displayed
On
Current linefeed setting
The mode may be altered. The correct values are accessed by ,
LF
Flashes for Fluke products online at the factory and ...
Manual - Page 40
... entered in Section . The commands are used with all commands. For example "s" returns the current set-point and "s=150.0" sets the set : 150.00 C
t: 9999.9 {C or F} t: 55.6 C
u: x
u: C
Acceptable... upper case may be used. Characters are optional for Fluke products online at: www.
.com 1.877.766.5412...9100S Dry-Well Calibrator
Interface Commands
The serial port can be used.
Manual - Page 46
9100S Dry-Well Calibrator
Calibration Procedure
9.2.1 Compute DELTA A = T3 − T2 B = ... measured temperature and set-point resistance at 50.0 °C T2 and R2 are the measured temperature and set-point resistance at 200.0 °C T3 and R3 are the measured temperature and set-point resistance at ... above (Section )
38
MyFlukeStore Shop for Fluke products online at: www.
.com 1.877.766.5412
Manual - Page 51
...displays shows '-init-,' the model number, and the firmware version. The scan and scan rate settings may be incorrect. Improper line voltage. Wait. Controller problem. Err 1 - a Structure error Err 4 - Check this value as described in Section 6.9, Operating Parameters on the Report of the controller parameters and calibration constants must be on troubleshooting, CE Comments, and a wiring...
Datasheet - Page 4
... dry-well.
754 DOCUMENTING PROCESS CALIBRATOR
2514 dry-well interface cable
Null modem
Fluke Calibration Dry-well (DB9)
Ordering information
9100S Handheld Dry-Well 8 9300 Rugged Carrying Case, 9100
9102S Handheld Dry-Well, comes with your choice of temperature sensors • 9100S model weighs only 2 lbs, 3 oz (1 kilogram) • Temperature ranges from -10 °C to...
Fluke 9100S-B-156 Reviews
Do you have an experience with the Fluke 9100S-B-156 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Fluke yet.
Earn 750 points for your review!