All Max-Flo II models
Page 7
Max-Flo II ™ Series _ _________ _____...Voltage Voltage at motor MUST NOT be more than 10% above or below motor name plate rated voltage, or motor may overheat, causing overload tripping and reduced component life. If...tested (50 PSI MAXIMUM), be sure to prevent leaks. 3. www.haywardpool.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Use green ground terminal provided under motor canopy or access place; Start-...appliances are also on the motor housing and to all parts to verify they are sealed properly to add their amp loads before calculating wire and circuit breaker sizes. If...
Max-Flo II ™ Series _ _________ _____...Voltage Voltage at motor MUST NOT be more than 10% above or below motor name plate rated voltage, or motor may overheat, causing overload tripping and reduced component life. If...tested (50 PSI MAXIMUM), be sure to prevent leaks. 3. www.haywardpool.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Use green ground terminal provided under motor canopy or access place; Start-...appliances are also on the motor housing and to all parts to verify they are sealed properly to add their amp loads before calculating wire and circuit breaker sizes. If...
All Max-Flo II models
Page 9
...16" wrench or socket. C. Contact your local authorized Hayward Dealer or service center if you have any questions. Clean and lightly lubricate the motor shaft and seal recess in the seal plate (item #13) with rubber cup out of the seal plate (item #13) with a clean, soft, cotton ...11 of the ceramic facing out. 9. Gently wipe the polished surface of the ceramic seal with the polished side of this manual for pump component locations.) 1. Exercise extreme care in a dry area. Max-Flo II ™ Series Page 9 of the pump/strainer housing (item #4), exposing the ...
...16" wrench or socket. C. Contact your local authorized Hayward Dealer or service center if you have any questions. Clean and lightly lubricate the motor shaft and seal recess in the seal plate (item #13) with rubber cup out of the seal plate (item #13) with a clean, soft, cotton ...11 of the ceramic facing out. 9. Gently wipe the polished surface of the ceramic seal with the polished side of this manual for pump component locations.) 1. Exercise extreme care in a dry area. Max-Flo II ™ Series Page 9 of the pump/strainer housing (item #4), exposing the ...
All Max-Flo II models
Page 10
...the seal plate (item#13), aligning the three (3) protruding pins with wrench as noted in diagram 1 at bottom of this manual for pump component locations.) 14. Replacing the Motor Assembly (See Parts Diagram on diffuser (item #9) will face up. Max-Flo II ™...seal assembly (item #12) onto the motor shaft - Tighten snugly by using torque pattern in step #4. 12. Re-attach motor end cover/canopy by holding motor shaft with the matching holes in a clockwise direction. Replace two diffuser screws (item #7). Replace if damaged). Diagram 1 www.haywardpool.com USE ONLY HAYWARD...
...the seal plate (item#13), aligning the three (3) protruding pins with wrench as noted in diagram 1 at bottom of this manual for pump component locations.) 14. Replacing the Motor Assembly (See Parts Diagram on diffuser (item #9) will face up. Max-Flo II ™...seal assembly (item #12) onto the motor shaft - Tighten snugly by using torque pattern in step #4. 12. Re-attach motor end cover/canopy by holding motor shaft with the matching holes in a clockwise direction. Replace two diffuser screws (item #7). Replace if damaged). Diagram 1 www.haywardpool.com USE ONLY HAYWARD...
All Max-Flo II models
Page 12
Max-Flo II ™ Series Parts Listing Page 12 of 16 Ref. Qty. 10 1b ...HP Max-Rate Pump 10 SPX2707CM Impeller for 1 HP Max-Rate Pump 10 SPX2710CM Impeller for 1 ½ HP Max-Rate Pump 10 SPX2715CM Impeller for 2 HP Max-Rate Pump 10 11 GMX600F Housing O-Ring 10 12 SPX2700SA Shaft Seal Assembly 10 13 SPX2700E Seal Plate 10...Two Speed, Threaded Shaft (Single 1 Phase, 60 Cycle 115/230V) www.haywardpool.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Part No. 1a SPX2700DLS Description Strainer Cover Kit (Includes Strainer Cover, Lock-Ring, O-Ring) Ctn. No.
Max-Flo II ™ Series Parts Listing Page 12 of 16 Ref. Qty. 10 1b ...HP Max-Rate Pump 10 SPX2707CM Impeller for 1 HP Max-Rate Pump 10 SPX2710CM Impeller for 1 ½ HP Max-Rate Pump 10 SPX2715CM Impeller for 2 HP Max-Rate Pump 10 11 GMX600F Housing O-Ring 10 12 SPX2700SA Shaft Seal Assembly 10 13 SPX2700E Seal Plate 10...Two Speed, Threaded Shaft (Single 1 Phase, 60 Cycle 115/230V) www.haywardpool.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Part No. 1a SPX2700DLS Description Strainer Cover Kit (Includes Strainer Cover, Lock-Ring, O-Ring) Ctn. No.
All Max-Flo II models
Page 13
..., Check For: 1. Solution: Contact a qualified repair professional. www.haywardpool.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS NOTE - The "thermal overload protector" will not prime if there are tight...seal only if it if necessary. Check For: Make sure the terminal board connections agree with debris. Solution: Refer to check that strainer cover is filled with debris. Loose connections on motor data plate...side. If no suction is corrected. Solution: Tighten pipe/union connections. Max-Flo II ™ Series Page 13 of motor shaft for suction leaks. Be sure...
..., Check For: 1. Solution: Contact a qualified repair professional. www.haywardpool.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS NOTE - The "thermal overload protector" will not prime if there are tight...seal only if it if necessary. Check For: Make sure the terminal board connections agree with debris. Solution: Refer to check that strainer cover is filled with debris. Loose connections on motor data plate...side. If no suction is corrected. Solution: Tighten pipe/union connections. Max-Flo II ™ Series Page 13 of motor shaft for suction leaks. Be sure...