Hitachi NV83A2 - 3 1/4 Inch Full Head Fraiming Coil Nailer Support and Manuals
Get Help and Manuals for this Hitachi item
View All Support Options Below
Free Hitachi NV83A2 manuals!
Problems with Hitachi NV83A2?
Ask a Question
Free Hitachi NV83A2 manuals!
Problems with Hitachi NV83A2?
Ask a Question
Most Recent Hitachi NV83A2 Questions
Nail Gun
nail gun wont keep firing nails while trigger is held only fires one nail then i have to release tri...
nail gun wont keep firing nails while trigger is held only fires one nail then i have to release tri...
(Posted by rcbender 12 years ago)
Popular Hitachi NV83A2 Manual Pages
Instruction Manual - Page 3
... injury. WARNING indicates a potentially hazardous situation which contain the operation and maintenance instructions. CAUTION indicates a potentially hazardous situation which , if not avoided, will result...procedures.
Never use this Nailer for applications other than those specified in this Manual and in the sections which , if not avoided, could result in this manual before it occurs...
Instruction Manual - Page 4
...it contains fasteners or not. Respect the Nailer as the Nailer can lead to pressure which potentially exceeds 200 psi (13.7 bar 14 kgf/cm2) as a working implement.
...USE OXYGEN OR OTHER BOTTLED GASES. Always wear head protection to protect your head from loud noise. English
SAFETY
IMPORTANT SAFETY INSTRUCTIONS FOR USING NAILERS
READ ALL INSTRUCTIONS
DANGER
1. Always assume the Nailer...
Instruction Manual - Page 6
... you drowsy.
29. The Nailer should never be operated by Hitachi, distributor or employer shall repair the Nailer. USE ONLY PARTS, ACCESSORIES OR FASTENERS SUPPLIED OR RECOMMENDED BY HITACHI. Never modify or alter a nailer. IMPORTANT SAFETY INSTRUCTIONS FOR USING NV83A2 • NV65AC • NV50A1 COIL NAILER
WARNING
1. If driving fasteners with the nail guide open, the fasteners can...
Instruction Manual - Page 7
... operators and others in work area are not further used before repair. SAVE THIS MANUAL AND KEEP IT AVAILABLE FOR OTHERS!
- 7 - Enforce the use of EYE PROTECTION by operators and others in safe working order.
5. Keep Nailers in work area.
4. English
SAFETY - Maintain Nailers properly.
6. Ensure that this MANUAL is available to operators and personnel performing maintenance...
Instruction Manual - Page 8
... illustrations in the safe operation of the Nailer. NAME OF PARTS
Exhaust Cover Piston
Piston O-ring Driver Blade
Nose
Body
Trigger Cap
Air Plug (Sold separately) Magazine
Magazine Assembly
Section A-A
Main nail stopper
Nail guide
Feeder
Push Lever
Feed piston
Feed spring
Firing Head (Outlet)
Knob Dust Cover
Magazine Cover Nail Holder
Exhaust Cover Trigger
Body
Piston
Piston...
Instruction Manual - Page 9
...283" (7.2 mm)
NV65AC
Min.
NOTE: Use only genuine Hitachi nails to malfunction and resulting injuries. NV83A2
Min.
ACCESSORIES
.083" (2.1 mm)
.083" (2.1 mm)
Wire-collated coil nails
WARNING
ⅷ Accessories other than those shown below can lead to assure nail quality and driving ease. English
SPECIFICATIONS
Model
NV83A2
NV65AC
NV50A1
Operating pressure
70 - 120 psi...
Instruction Manual - Page 10
...
⅜ Sequential Trip Mechanism Kit (Code No. 876762)
(Single Shot Parts)
⅜ Pneumatic Tool Lubricant
.8 oz. (25 cc) oil feeder
(Code No. 877153)
4 oz. (120 cc) oil feeder
(Code No. 874042)
1 quart (1 ltr) can
(Code No. 876212)
NOTE: Accessories are subject to change without any obligation on Nailer.
1. AIR SUPPLY
DANGER
ⅷ NEVER use oxygen or other
types of...
Instruction Manual - Page 11
... required =number of Nailers × average nails driven each minute per minute Amount of the maximum pressure produced in the system, whichever is already cold, bring it in a warm area until beginning the work , test the Nailer by using the Nailer and contact a Hitachi authorized service center immediately.
- 11 - This will wear prematurely. ⅜ Use Hitachi pneumatic tool lubricant...
Instruction Manual - Page 13
... hole Guide slot First nail 2 3 Nail Guide
4 1
Guide surface 2 Feeder
4 Pulling the nails to the nail
length. If the magazine cover is not correctly adjusted.
Magazine
Magazine cover
Nail holder
English
(3) Place the nail coil into the driving hole and the second nail between the two pawls of the plate according to the right, swing the nail guide closed.
(5) Close the magazine cover...
Instruction Manual - Page 14
... and 2" (45 mm and 50 mm)
Magazine Cover
Mark
Nail Holder
NOTE: Before loading nails in the guide slot. Driving Hole Guide Slot FirstNail 2 3 Nail Guide
4 1
Guide Surface 2 Feeder
NOTE: Be careful not to deform the collated wires and not to ANSI Z87.1 specifications.
Insert the first nail into the magazine opening.
Nail
- 14 - The nail will not close correctly.
4 Pulling the...
Instruction Manual - Page 15
... repeat this Nailer. This Hitachi nailer has a STANDARD CONTACT TRIP MECHANISM (Bounce Fire). There are : 1. They are two methods of operation to drive nails with the push lever and does not operate unless the push lever is not in work area.
ⅷ Keep fingers AWAY from the trigger. As soon as order part number 876762...
Instruction Manual - Page 16
... yourself or others in the following "Method of the nails. ⅷ After nailing: 1) disconnect air hose from the Nailer; 2) remove all warnings and instructions. ⅷ Always handle nails and package carefully. If nails are driven too shallow, turn the adjuster to all nails from the Nailer; 3) supply 5 - 10 drops of Hitachi pneumatic tool
lubricant into the workpiece, adjust the...
Instruction Manual - Page 17
...Lubricate it with a slotted screw driver.
Inspecting the feeders
1 DISCONNECT AIR HOSE. 2 Clean the knob sliding part. Nail Guide
Nail Slotted Screw Driver
5 Cut the deformed collated wire with a hammer.
Some illustrations in this Manual is designed to assist you in the safe maintenance of frequent jam, contact a Hitachi authorized service center. English
MAINTENANCE
NOTE: The...
Instruction Manual - Page 18
... for repair. B: Code No.
Storing
⅜ When not in use . WARNING LABEL
Change the WARNING LABEL if missing or damaged. Accordingly, some parts (i.e.
Warning Label
9. This Parts List will eventually require servicing or replacement of parts because of wear from a Hitachi authorized service center. code numbers and/or design) may have accumulated in the magazine...
Instruction Manual - Page 19
...blade worn? Contact Hitachi for replacement.
Keep the Nailer operated properly.
Supply 5 - 10 drops of moisture and dirt.
Clear a jam per page 17. Driver blade worn?
Use only recommended nails. Use Hitachi pneumatic tool lubricant. Clean magazine and feeder mechanism.
Operator troubleshooting Most minor problems can be resolved quickly and easily using the table below...
Hitachi NV83A2 Reviews
We have not received any reviews for Hitachi yet.