Honeywell 3800ISR050-0F00E Support and Manuals
Get Help and Manuals for this Honeywell item
View All Support Options Below
Free Honeywell 3800ISR050-0F00E manuals!
Problems with Honeywell 3800ISR050-0F00E?
Ask a Question
Free Honeywell 3800ISR050-0F00E manuals!
Problems with Honeywell 3800ISR050-0F00E?
Ask a Question
Popular Honeywell 3800ISR050-0F00E Manual Pages
User Manual - Page 7
Terminal Interfaces
Terminal ID 2-1 Supported Terminals 2-2 Keyboard Country 2-4 Keyboard Style 2-5 Keyboard Modifiers 2-6
i Getting Started
3800i/3800r 1-1 About This Manual 1-1 Unpacking the Scanner 1-1 3800i Models 1-2 3800r Models 1-3 3800i/3800r Scanner Identification 1-4 3800i Scanner (with aimer beam option) Identification ....... 1-5 Connecting the Scanner When Powered by Host...
User Manual - Page 15
...and the ability to the
carrier who delivered the carton.
3800i/3800r User's Guide
1 - 1 About This Manual
This User's Guide provides installation and programming instructions for handheld scanners. The performance of Adaptus technology delivers aggressive read poor quality bar codes. Unpacking the Scanner
After you open the shipping carton containing the imager, take the following steps...
User Manual - Page 25
... IBM SurePos (USB Tabletop scanner).
3800i/3800r User's Guide
1 - 11
Verify the scanner operation by scanning a bar code from the Sample
Symbols in the back of a computer. 1. Connect the appropriate interface cable to the scanner and to the USB port of this interface applies to 3800r Models and on specific
models. Refer to your scanner. Note: The following "Plug...
User Manual - Page 33
...
046
124*** 125*** 130 131*** 061
064
* Default for 3800i/3800iSR050E models ** Default for 3800rSR030E model (applies to 3800rSR030E models only) ***Applies to program these interfaces, rather than scanning the terminal ID listed in this table.
3800i/3800r User's Guide
2 - 3 It is best to use the Plug and Play bar codes on page 1-12 to 3800i...
User Manual - Page 41
... sends data in addition to changing the terminal ID. The Code 39 Format bar code below sets the terminal ID to 61, and the Same Code Format bar code sets the terminal ID to emulate a wand reader. Code 39 Format
Same Code Format
3800i/3800r User's Guide
2 - 11 Default = RTS/CTS, XON/XOFF and ACK/ NAK Off
RTS/CTS...
User Manual - Page 49
... is not high enough, Presentation Mode will not work when a scanner is presented to read the same bar code a second time. Longer delays are off until a bar code is programmed for the laser emulation interface. Use shorter delays in manual trigger mode by setting the Hands Free Time-Out.
If the light level in minimizing...
User Manual - Page 52
... scan the percent you set the time-out by the scanner. Aimer Beam Time-Out (Aimer Beam option only)
Aimer Beam Time-Out powers down the aimer beam after a time-out if the trigger is turned on the inside the back cover of this manual. At least part of a bar code must be within the...
User Manual - Page 56
... the example on page 3-11, but assume a suffix and specific code lengths, you would have to use the following command line:
SEQBLK62001141FF6A001242FF69001143FF
3 - 12
3800i/3800r User's Guide Code 128
C - Note: Code 93 must be enabled to count any programmed prefixes, suffixes, or formatted characters as part of the command line is shown below:
SEQBLKsequence editor start...
User Manual - Page 63
... User's Guide
4 - 5 Scan the SAVE bar code using the Programming Chart inside the back cover of this manual. Scan the SAVE bar code using the Programming Chart inside the back cover of steps to 0. Prefix
Scanned Data Suffix
1234 5 Intercharacter Delay
Intercharacter Delay
To remove this delay, scan the Delay Length bar code, and set the...
User Manual - Page 66
...the Supported Terminals...manual...Guide
If you want to the Format Editor Commands Chart (page 5-2).
inside back cover to program the scanner... for your entries. For example, scan 0 0 3 for each symbology data format. Syntax = F1xx (xx stands for the hex value for an ASCII code, see ASCII Conversion Chart (Code Page 1252) on page A-1), and the bar code data length for the specific...
User Manual - Page 72
... parity), while in the same format as a wand scanner. Wand Emulation Code 39 Format
Wand Emulation Same Code Format
6 - 2
3800i/3800r User's Guide RS-232 programmable selections are used by scanning the Disable bar code below sets the terminal ID to 61, and the Same Code Format bar code sets the terminal ID to 64. If you want to...
User Manual - Page 75
... time-out duration for the time set the time the imager should remain in manual trigger mode by setting the Hands Free Time-Out. Default = 120 seconds. You can set with the Low Power Time-Out bar code. Note: If you change the time-out duration. Then, the scanner goes to manual trigger mode. Low Power Time...
User Manual - Page 82
... will transmit this character at the end of the scanned data. Minimum Default = 0, Maximum Default = 48. When Check Character is set to Validate and Transmit, the scanner only reads Code 39 bar codes printed with a check character, and will not transmit the check character with the scanned data. Refer to change the message length...
User Manual - Page 135
...Code 11 Code 11 Code 11 Check Digits Required Code 11 Message Length
Code 128 Code 128
ISBT Concatenation
Code 128 Message Length Code 128 Code Page Code 128 Function Code Transmit ISBT Concatenation Telepen
Telepen
Telepen Output
Telepen Message Length UPC A
Minimum (1 - 80) *4 Maximum (1 - 80) *80 Default All Code 11 Settings...
7-17 7-17 7-17 7-17 7-17 7-17
7-18
3800i/3800r User's Guide
11 - 13
User Manual - Page 151
... lens tissue dampened with water only.
solvents may degrade if the scanner's window is not clean. Cable replacement instructions are to be performed on page 14-1 for further information. Although specific maintenance is not required, the following periodic checks ensure dependable scanner operation:
Cleaning the Scanner's Window
Reading performance may damage the finish or the window...
Honeywell 3800ISR050-0F00E Reviews
We have not received any reviews for Honeywell yet.