IC Realtime ICIP-D4002-IR-2.8 Support and Manuals
Get Help and Manuals for this IC Realtime item
View All Support Options Below
Free IC Realtime ICIP-D4002-IR-2.8 manuals!
Problems with IC Realtime ICIP-D4002-IR-2.8?
Ask a Question
Free IC Realtime ICIP-D4002-IR-2.8 manuals!
Problems with IC Realtime ICIP-D4002-IR-2.8?
Ask a Question
Popular IC Realtime ICIP-D4002-IR-2.8 Manual Pages
Product Datasheet - Page 2
...ICIP-D4002-IR-2.8
Specifications
Model
Image Sensor Effective Pixels Scanning System Electronic Shutter Speed Min. User Access Smart Phone
Power Supply
ICIP-D4002-IR-2.8 Camera
1/3" 4 Megapixel progressive scan CMOS 2688(H)×1520(V) Progressive Auto/Manual, 1/3(4)~1/10000s [email protected](color), [email protected] (IR... off) H.264: 32K ~ 10Mbps Support
Smart Function Tripwire, Intrusion, Scene change...
Product Datasheet - Page 3
Less than 95% RH IP66 IK10 Φ6.3"×2.0"/Φ106mm×50.3mm 0.77lb/0.35kg
IC Realtime LLC 3050 N Andrews Avenue Extension Pompano Beach, FL 33064 (866) 997-9009 www.icrealtime.com
Designs and specifications subject to change without notice. Power Consumption Working Environment Ingress Protection Vandal Resistance Dimensions Weight
< 5W -40°F ~ 140...
Product Manual - Page 17
..., zoom, focus, iris, preset, tour, pan, scan, pattern, aux close,
and PTZ setup button. Parameter
Note
PTZ direction
PTZ supports eight directions: left/right/up/down/upper left/upper right/bottom left/bottom right.
Here you have properly set PTZ protocol. (Please refer to Quick Position quickly positioning. Step length control PTZ...
Product Manual - Page 32
5 Setup
Web client setup support camera, network, time, storage, system and system info view.
5.1 Camera
5.1.1 Conditions
Here you set and view config and its effect.
Figure ...setups become hazy if the value is too high. The larger the number, the bright the video is to 100.
Please note the video may become valid immediately after you can adjust this value if the video is 50.
28...
Product Manual - Page 34
When you have installed the auto iris. Exposure Auto Iris
Note...noise: The video whole brightness can automatically change within the proper exposure range according to display manual exposure value. The higher the gain max value is, the lower the noise is on by default... range according to the different environments. Before the setup, please make sure you disable this function.
Product Manual - Page 35
... quality. Auto: The auto white balance is on.
Note: Only some non-IR devices support sensor input function.
It adjusts delay value of color and black/white switch. Note:
Available only when day/night is 6.
System can set the white balance mode.
Its value range is 2~10, and default is auto.
31...
Product Manual - Page 47
... IP address, WEB will automatically jump to activate the new setup once you can access the IP address of these two version. It max supports 15 characters. Please note you modify the default setup.
Select DHCP mode, it auto searches IP, and you must manually set IP/subnet mask/gateway. Mac Address
It is to...
Product Manual - Page 48
...Go to the steps listed below.
Now you can use ARP/Ping command to modify or set device IP address service.
Step 6: Open the browse and then input http://. Preferred DNS DNS IP address. ...from 192.168.0.125 ..."
Alternate DNS Alternate DNS IP address. Set the network camera and the PC in the same LAN. Step 5: You can see the setup is OK if you know the device MAC address. Step ...
Product Manual - Page 58
... its service information and listen to set multicast address and port. The Bonjour device can auto detect the network camera of the outer.
Please note the safari browse support this function...on the multicast DNS service from other device. You can just send out one data to reduce the broad width and the CPU load. Parameter
Encryption Password
Function Password not less than 8...
Product Manual - Page 62
... access control protocol) supports manual selection of Service) is network security mechanism. Parameter
Function
Authentication PEAP (protected EAP protocol). Qos (Quality of authentication method to control if device connected to distinguish the data packet so that the router or the hub can join the LAN. We can set the DSCP (Differentiated Services Code Point) of the...
Product Manual - Page 73
... 2. From Monday to Sunday select record time, click on setup on Record Schedule, see Figure 5- 51. Set period according to schedule. 5.4.1.1 Record Schedule Record schedule steps:...General, Motion,
and Alarm.
69 Figure 5- 49
5.4 Storage Management
5.4.1 Schedule
Before schedule setup, user must set record mode is off, then device will not snapshot according to actual need. Note: If...
Product Manual - Page 82
... can modify other user's password.
The user amount is 18 and the group amount is 8 when the device is shipped out of the factory. Update period
It is to set the rights for the respective user in the following user name or the user group name, system max supports 15digits. You can be...
Product Manual - Page 86
Figure 5- 70
Please refer to the following sheet for detailed information. Data Bit Stop bit Parity
Default setup is 1. Please note system cannot restore some series products support this function. Address
Baud Rate
Set corresponding dome address. Select the dome baud rate.
The PTZ interface is shown as in Figure 5- 70.
otherwise you can...
Product Manual - Page 89
... ".bin") and then click the update button to begin firmware update. Please select the upgrade file (file extension is for reference only.
85
Figure 5- 75
5.6 Information
5.6.1 Version The version interface is shown as in device malfunction!
Auto Delete Old Files
Check it and set period within 1~31 days.
5.5.7 Upgrade The upgrade interface is shown as in Figure...
Product Manual - Page 92
... sheet for detailed information. Alarm input device sends out alarm. When alarm is unauthorized access. Here you can set device alarm type and alarm sound setup.
6 Alarm
Please note some series product does not support this function.
Click alarm function, you can see an interface is malfunction. Operation
HDD malfunction Camera masking External...
IC Realtime ICIP-D4002-IR-2.8 Reviews
We have not received any reviews for IC Realtime yet.