Icom M604A Support and Manuals
Get Help and Manuals for this Icom item
Popular Icom M604A Manual Pages
Instruction Manual - Page 1
INSTRUCTION MANUAL
VHF MARINE TRANSCEIVER
iM604A
Instruction Manual - Page 2
...IMPORTANT
READ ALL INSTRUCTIONS carefully and completely
before using Icom' s MA-500TR Class B AIS Transponder
Icom, Icom Inc. SAVE THIS INSTRUCTION MANUAL -
The IC-M604A VHF MARINE TRANSCEIVER is a registered trademark of Icom Incorporated (Japan...of trouble-free operation.
Many hours of research and development went into the design of your radio of choice, and hope you agree with Icom's ...
Instruction Manual - Page 4
...Do not transmit with gain not greater than the allowable MPE level set by a grounded metallic barrier.
Determining MPE Radius THE MAXIMUM PERMISSIBLE...FOR A SHIP MOUNTED SYSTEM. RADIO OPERATOR WARNING
Icom requires the radio operator to meet all RF exposure compliance requirements.... without suitable structures, the antenna must be mounted so as driver or radio operator) are within the MPE radius of the...
Instruction Manual - Page 5
... 47
■ Set mode items 47
12
9 CONNECTIONS AND MAINTENANCE 50-57
■ Connections 50
■ Fuse replacement 51
■ Supplied accessories 51
■ Antenna 51
■ Mounting the transceiver 52
■ MB-75 installation 53
■ UT-112/UT-98 installation 54
■ HM-157/HM-162 installation 55
10 TROUBLESHOOTING 58
11 SPECIFICATIONS AND OPTIONS...
Instruction Manual - Page 11
... position data is manually input.
!4 SCAN INDICATOR ➥ "24+5%#0 " appears during Priority scan; The last position data is held for only 23.5 hours, and after that , "0Q2QUK VKQP" will appear. ➥ ".QECN" appears when the offset time data is set. (p. 42) ➥ "0Q 6KOG" appears when no GPS receiver is connected...
Instruction Manual - Page 12
...'s power to transmit; release to receive. (p. 9)
w CHANNEL UP/DOWN KEYS [Y]/[Z] ➥ Push either key to change the operating channels, Set mode settings, etc. (pp. 7-9, 47) ➥ Checks TAG channels, changes scanning direction or manually resumes a scan. (p. 15)
e TRANSMIT POWER KEY [HI/LO] ➥ Push to toggle the power high and low. (p. 9) • Some...
Instruction Manual - Page 14
...for monitoring broadcasts from NOAA (National Oceanographic and Atmospheric Administration.)
The transceiver can be set for your operating area. q Push [CH/WX] to select a regular channel....
76% 6'.'2*10'
8
’0 ’9
76%
%%)
D Weather channels
The IC-M604A has 10 weather channels.
These are used for duplex channels. • "A" appears when a simplex ...
Instruction Manual - Page 17
... cancel and exit the screen. The IC-M604A emits a vibrating noise when this function is pushed and held to input and set the comment. • The cursor and... 3
■ Channel comments
Each channel can be labeled with a unique alphanumeric ID of [VOL] control setting. • All other channel comments, if desired.
• Selectable characters
KEY
CHARACTERS
KEY
CHARACTERS
3...
Instruction Manual - Page 21
... TAG of unwanted channels.
rection, or to set the Priority or Normal scan type, and the scan resume timer in the group as a TAG channel.
r Push [O], then push [4• SCN ] to change the scanning di- e Push [O], then push [5• TAG ] to resume the scan manually.
• A beep tones sounds and "" blinks when...
Instruction Manual - Page 22
... ID
q Enter "#FF +0&8+&" in the DSC Set up menu. q First, turn ON the power to move the cursor backward or forward.
&5% /GPW //5+ %JGEM
AAAAAAAAA
%.4 'ZKV '06 1- 6 DSC OPERATION
■ MMSI code programming
The 9 digit MMSI (Maritime Mobile Service Identity: DSC self ID) code can be performed TWICE. This code programming can be entered, and a name...
Instruction Manual - Page 24
...edit W; They are automatically included when a GPS receiver (NMEA0183 ver. 2.0 or 3.01) is connected.
• Manual programming is disabled when a GPS receiver (NMEA0183 ver. 2.0 or 3.01) is connected, your position (latitude and ... %.4 'ZKV '06 1- East longitude or [9•WXY] to set the position.
If no GPS is connected.
• Manually programmed position/time data will be...
Instruction Manual - Page 25
...; A warning alarm sounds when the GPS data has been interrupted for 10 minutes, or has not been manually updated for 4 hours.
■ GPS information display
When a GPS receiver (NMEA0183 ver. 2.0 or 3.01) is not supplied from Icom. may blink instead of input precedence is 'RMC,' 'GGA,' 'GNS', 'GLL' and 'VTG.'
➥ When sentence...
Instruction Manual - Page 29
... of position and time displays when the GPS data is invalid, or has not been manually updated for 4 hours.
■ Transmitting DSC Calls
To ensure the DSC function operated correctly, please make sure you set the 9 digit MMSI ID code for 23.5 hours, or until the power is turned OFF. ➥ The Distress call...
Instruction Manual - Page 55
...; is not controlled by the optional command microphone. OFF : The transceiver's power is connected)
This item sets the Radio power function to ON or OFF.
D Scrambler code (Appears when a scrambler unit is installed)
The scrambler code can be set depending on dealer setting. • 32 codes (1 to 32) can be selected for UT-112. (Default: 1) • 128...
Instruction Manual - Page 64
... be • MMSI (DSC self ID) code is open.
• Turn the beep tone ON in the Set
mode.
• Push [6• LO/DX ] after pushing [O] to water.
• Internal speaker is turned OFF. • Turn the optional voice scrambler ON.
not turn the function OFF.
10 TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
SOLUTION
REF.
p. 9 p. 9 p. 11...
Icom M604A Reviews
We have not received any reviews for Icom yet.