Icom V80 HD Support and Manuals
Get Help and Manuals for this Icom item
Popular Icom V80 HD Manual Pages
Instruction Manual - Page 1
INSTRUCTION MANUAL
VHF TRANSCEIVER
iV80 iV80E
This device complies with Part 15 of the FCC Rules. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) ...
Instruction Manual - Page 2
... Icom product. struction manual contains important operating instructions for optimum use the VOX operation, an optional headset and a plug adapter cable are attached.
❍ Built in -
Equipment damage may occur. We want to take a couple of moments of your time to thank you for purchasing this product should provide you for making your IC-V80...
Instruction Manual - Page 7
...; Tone scan 34
9 DTMF MEMORY 35-37 ■ Programming a DTMF code sequence 35 ■ Transmitting a DTMF code sequence 36 ■ Confirming a DTMF memory 37 ■ Setting DTMF transfer speed 37
10 SET MODES 38-47 ■ Set mode programming 38 ■ Set mode items 39 ■ Initial Set mode programming 43 ■ Initial Set mode items 44
11 CLONING 48...
Instruction Manual - Page 10
... PTT SWITCH [PTT] ➥ Push and hold to transmit, release to receive. (p. 17)
For IC-V80E only ➥ Push briefly, then push and hold to open the squelch temporarily to monitor the ...Set mode, rotate to select a desired option or value. (pp. 38, 43)
r EXTERNAL SPEAKER/MICROPHONE JACKS [SP MIC] Used to adjust the squelch level. (p. 14) ➥ Enters or sends the DTMF code 'A.' (pp. 35...
Instruction Manual - Page 12
...; After pushing [FUNC](M), enters the Set mode.
(p. 38)
[9] • [H/M/L](9) ➥ Numeric input and DTMF code: '9' ➥ After pushing [FUNC](M), selects the output
power between high, middle and low. (p. 17)
[0] • [DTMF-M](0) ➥ Numeric input and DTMF code: '0' ➥ After pushing [FUNC](M), enters the DTMF
memory mode. (p. 35)
[M] • [FUNC](M) ➥ DTMF...
Instruction Manual - Page 16
... stop using clean water, any part of the body that is discolored or deformed. If any purpose that comes into contact with Icom radios or Icom chargers.
Misuse can result. High...battery gas may rupture. Only Icom battery packs are tested and approved for which it emits an abnormal odor, heats up, or is not specified in this instruction manual.
R DANGER! If the ...
Instruction Manual - Page 17
... sun-heated vehicle, or in an induction heating cooker. If the
battery is left unused for charging. Icom recommends charging the battery at the following temperature range:
-20˚C to +50˚C (-4˚F to... +122˚F) (up to a month) -20˚C to +35˚C (-4˚F to +95˚F) (up to three months) -20˚C to +20˚C (-4˚F to...
Instruction Manual - Page 21
...level. • If the squelch is closed, push and hold [ ] for 1 sec. "SqL 0" is open 14
the squelch manually. 4 BASIC OPERATION
■ Power ON
➥ Push and hold [MONI] to adjust the squelch level.
3
• "SqL ....
18
19
14 You can use it without disturbing the 15
squelch setting, even when mute functions such as the tone
squelch are in use.
16
➥ Push and hold [ ] for...
Instruction Manual - Page 24
... holding [MONI], push [] or []. • The squelch level is displayed on the LCD while setting. • "SqL 1" is loose squelch (for weak signals) and "SqL10" is open the squelch manually.
r For the squelch level setting. (Push to turn power ON.
r S peak into the microphone using your normal voice level. • DO...
Instruction Manual - Page 28
... 144.700 MHz 145.300 MHz
• "-" or "+" blinks when the reverse duplex function is shown in the Set mode. version: The auto repeater function has priority over the manual duplex setting. q Push [FUNC](M), and then [SET](8) to select the offset item.
• "±" blinks, and the current frequency offset appears. w Push [] or...
Instruction Manual - Page 29
...the tone scan is temporarily set in advance. Subaudible tones are superimposed over your normal signal, and must 8
transmit a 1750 Hz tone burst.
9
For IC-V80E only
Push [PTT] ...SCAN](3) to transmit their assigned DTMF codes.
• The transceiver has 16 DTMF memory channels (p. 35).
6
1750 Hz TONE
7
To access some European repeaters, the transceiver must be set .
19
• See page...
Instruction Manual - Page 41
... you can determine the subaudi- 3
ble tone required to access the repeater or open the squelch manually, push and hold [MONI].
However, the signal indicator shows the signal strength. • To open... a tone frequency or DTCS code is detected, the tone
scan pauses according to the scan resume setting (p. 30)
13
• The decoded CTCSS tone frequency or DTCS code is activated. • ...
Instruction Manual - Page 43
... to the pushed key.
• dmt.m : T ransmits the programmed DTMF code sequence in the DTMF memory channel assigned to exit the Set mode. Select a desired option in countries out of Europe.
D Manual DTMF code transmission
First, set the DTMF TX key to "dmt.k" in the Set mode.
11
➥ W hile pushing and holding [PTT], pushing either...
Instruction Manual - Page 56
... pushing and holding [VFO/MR/CALL], push and
hold [ ] for 1 sec. D Partial reset
If you want to their default settings.
NOTE: No message appears on the display after the par- If the problem persists, perform either or both of the procedures below. 12 RESETTING
■ Resetting
The LCD may be caused externally...
Instruction Manual - Page 57
...sta- • A different tone or code is • Check the external ...following points before sending it to a service center.
1
PROBLEM
POSSIBLE CAUSE
SOLUTION
REF.
2
The ... the battery pack, or replace the batteries.
the cloning cable....set .
• The key lock function is too low.
• Rotate [VOL] to adjust to the [SP] jack. 13 TROUBLE SHOOTING
If your transceiver seems to be set...
Icom V80 HD Reviews
We have not received any reviews for Icom yet.