Makita CT227R Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita CT227R manuals!
Problems with Makita CT227R?
Ask a Question
Free Makita CT227R manuals!
Problems with Makita CT227R?
Ask a Question
Popular Makita CT227R Manual Pages
FD05/FD06 Instruction Manual - Page 3
... 2. Check for which may be caught in this instruction manual may contact hidden wiring. Keep cutting tools sharp and... your power tool serviced by a qualified repair person using the tool in accordance with these instructions to operate the ...) replace strict adherence to prevent dust inhalation and skin contact. When battery pack is below when using only identical replacement
parts....
FD05/FD06 Instruction Manual - Page 5
... in the light or see that the switch trigger actuates properly and returns to become overloaded.
Electric brake
This tool is released, have the tool serviced at the end of the model number
1
2
1. The lamp goes out approximately 10 seconds after the switch trigger is equipped with "B" at a Makita...
FD05/FD06 Instruction Manual - Page 7
... x 22
ɸ4.1x 38
Hard wood (e.g.
Turn the sleeve clockwise to the instructions above. Sleeve To install the driver bit, pull the sleeve in the chuck as far as it . If it ... driver bit/socket bit.
2 3
1.
Installing or removing driver bit/ drill bit
For Model FD05 (optional accessory)
1
3
2
1. Place the driver bit/drill bit in the direction of the arrow and insert the driver...
FD05/FD06 Instruction Manual - Page 8
... performance and shorten the service life of the driver bit in metal
To prevent...guide screw makes drilling easier by pulling the drill bit into the protrusion at the point to be removed simply by setting the reversing switch to reverse rotation in the screw head, or the screw and/or driver...part on the tool/drill bit at the time of the drill bit in the driver bit holders. Installing driver...
FD05/FD06 Instruction Manual - Page 9
...replacement parts.
1.
NOTICE: Never use with your local Makita Service Center. Put the tool in the holster and lock it with the holster button so that it in this manual.
To maintain product SAFETY and RELIABILITY, repairs...: Always be performed by Makita Authorized or Factory Service Centers, always using the holster, remove a driver bit/drill bit from the tool. Using the tool...
FD05/FD06 Instruction Manual - Page 10
... limitation may also have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge. They may not apply to country. It is warranted to the tool. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of...
FD05R1/Z Parts Breakdown - Page 2
... ASS'Y
012
629169-7 DC MOTOR
013
911003-8 PAN HEAD SCREW M3X6
014
183B50-3 HOUSING SET
014 C10 252126-6 HEX. LOCKING NUT M4-7
014 D10
INC. 2
A01
251314-2 ...007 C10 620463-0 LED CIRCUIT
008
644813-5 TERMINAL
009
251451-2 - Model FD05R1/Z Parts list
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
Q'ty Unit
001
126233-0 SPEED CHANGE LEVER ASSEMBLY
001 ...
SH02 Instruction Manual - Page 3
...instructions, taking into account the working conditions and the work to be controlled with the switch is important to support...repair person using only identical replacement parts. When ripping, always use damaged or incorrect blade washers or bolt. Never use a rip fence or straight edge guide... tool serviced by insulated ...7. Recharge only with specifically designated battery packs. Under...
SH02 Instruction Manual - Page 4
...guard function 1. Lower guard may be serviced before making cut for special cuts such... they must be retracted manually only for any other part, in its path. Use... to serious personal injury.
9. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade...sure it may cause binding and kickback.
7. Supports must be bent. Raise the lower guard with...
SH02 Instruction Manual - Page 5
...clean.
Before setting the tool down...HOLD SHORT PIECES BY HAND!
11. Only use ) replace strict adherence to follow the safety rules stated in loss...Never attempt to saw base on that part of the lower guard which is solidly supported, not on the lower guard and...the saw held upside down . It may result in this instruction manual may be sure that is short or small, clamp it from...
SH02 Instruction Manual - Page 7
...lamps
Remaining capacity
Lighted
Off 75% to 25%
B
1
A
NOTE: Depending on the depth guide and
ENGLISH 7
Adjusting depth of cut , always tighten the clamping screw securely. Set for the desired angle (0° - 45°) by tightening the clamping screw. For 45&#...capacity
Only for battery cartridges with "B" at the end of the model number
move the base up for few seconds.
SH02 Instruction Manual - Page 8
...use the wrench to install or remove the circular saw blade.
4
2
ASSEMBLY
CAUTION: Always be sure that the tool is switched off lever. Return tool a MAKITA service center for proper repairs BEFORE further usage. WARNING.... Then remove the hex bolt, outer flange and circular saw blade. Inner flange
To install the circular saw blade cannot revolve and use the tool if it runs when you simply...
SH02 Instruction Manual - Page 10
...Set...accomplish this manual. A dirty...Guide rule)
Optional accessory
The handy rip fence allows you need any trouble develop during this time, for example, use the tool for a light-duty cut by Makita Authorized or Factory Service Centers, always using Makita replacement parts...repairs, any other maintenance or adjustment should be performed by the circular saw blade • Rip fence (Guide...
SH02R1/Z Parts Breakdown - Page 2
NUT M4 HEX. Model SH02 R1/Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
001
183C85-0
001 C10 807M91-8
001 D10
002
266560-4
... LOCK OFF LEVER CONTROLLER UNIT SWITCH SD-006-BB2AA-AA TERMINAL COMPRESSION SPRING 4 SWITCH LEVER TAPPING SCREW 4X18 HANDLE SET RUBBER PIN 4 RUBBER PIN 6 HEX. NUT M5 INC. 7 TAPPING SCREW 4X18 DUCT DC MOTOR SHAFT LOCK ...
SH02R1/Z Parts Breakdown - Page 3
...
961017-7 STOP RING E-3
056
268028-6 PIN 5
057
346339-0 ANGULAR GUIDE
058
961017-7 STOP RING E-3
059
135416-1 BASE ASSEMBLY
059 D10
INC. 53-58
A01
783202-0 HEX. SAW BLADE 85X15X20T
A03
456128-6 BATTERY COVER
A04
***DC10WD DC10WD BATTERY CHARGER
A05
BL1021B BATTERY BL1021B SET (197414-3)
A06
821663-7 PLASTIC CARRYING CASE
A06 C10 163455...
Makita CT227R Reviews
We have not received any reviews for Makita yet.