Makita HR2631F Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita HR2631F manuals!
Problems with Makita HR2631F?
Ask a Question
Free Makita HR2631F manuals!
Problems with Makita HR2631F?
Ask a Question
Popular Makita HR2631F Manual Pages
HR2631F Instruction Manual - Page 2
...ENGLISH (Original instructions)
SPECIFICATIONS
Model
Concrete
Core bit
Capacities
Diamond core bit (dry type)
Steel
Wood
No load speed (RPM)
Blows per minute
HR2631F HR2631FT HR2641 HR2630 HR2630T...and development, the specifications herein are subject to change without notice. • Specifications may differ from heat, oil, sharp edges or moving parts. The term ...
HR2631F Instruction Manual - Page 3
... the job better and safer at all times. Follow instruction for operations different from moving parts.
16. When using only identical replacement parts. The smaller the gage number, the heavier the cord... jewellery. If damaged, have the power tool repaired before turning the power tool on cord length and nameplate ampere rating. Service 24.
If in the hands of dust collection...
HR2631F Instruction Manual - Page 4
...the tool has not been used for the subject product. Keep hands away from repeated use) replace strict adherence
to follow the safety rules stated in place before operation.
7. they may cause... operation is secured in this
instruction manual may be extremely hot and could fly out and injure someone seriously. 13. Do not touch the bit or parts close to prevent dust inhalation and...
HR2631F Instruction Manual - Page 5
... switch action
CAUTION: • Always check the direction of lamp. Tool speed is fully set to change the direction of light
directly.
Switch action
CAUTION: • Before plugging in ... the dirt off and
unplugged before adjusting or checking function on the switch trigger. For Model HR2631F, HR2631FT, HR2630, HR2630T
CAUTION: • If the switch trigger can not be sure that ...
HR2631F Instruction Manual - Page 6
... counterclockwise rotation, you operate the tool in the direction of the quick change
drill chuck and set the line to the symbol. plus can clearly be sure that the action mode changing knob...drill chuck shows the symbol. Spindle 2. Changing the quick change chuck for SDSplus
For Model HR2631FT, HR2630T
The quick change drill chuck. Removing the quick change chuck for SDS-plus
...
HR2631F Instruction Manual - Page 7
...Bit shank 2. Protrusions
2. This chuck lubrication assures smooth action and longer service life. To use , always lower hook until it snaps into the...torque level is because they will stop turning. Hook
For Model HR2641
CAUTION: • Never hook the tool at ... as the torque limiter actuates, switch off and
unplugged before installing the bit.
1. When not in between the grooves on the...
HR2631F Instruction Manual - Page 8
...
2
015348
At this time, the depth gauge needs to be inserted so that the bit is directed to be secured at the desired angle. After installing, always make sure that the bit is convenient for drilling holes of
hex hole
1
marking on the
grip base
2. Turn the bit and push it...
HR2631F Instruction Manual - Page 9
... the inside periphery of bits which helps you prevent dust from the tool if installed on the dust cup is as follows. Attachment 4. Remove the bellows from the.... Bit 2. Bellows
1
2. Inside periphery 2. At that the symbol on the tool. Dust cup
1
1
1. Installing or removing the dust cup
(optional accessory)
2 1. Grooves 3. Flat side 3. Attach the dust cup to is ...
HR2631F Instruction Manual - Page 10
...vacuum cleaner to your bit, decrease the tool performance and shorten the service life of the tool and potentially severe injury.
015355
Set the action mode changing knob to the symbol. Blow-out bulb (... striking reinforcing rods embedded in the loss of control of the tool. • There is installed on the tool will not speed up the drilling. Hold the tool firmly with hammering" when...
HR2631F Instruction Manual - Page 11
...For Model HR2631F, HR2641, HR2630
1. Drill chuck assembly (optional accessory)
1
015357
Use the drill chuck assembly (optional accessory). When installing it , refer to "Installing ...installing it , refer to "changing the quick change lever to the position to 32 mm diameter in wood. Place the bit in the chuck as far as it will go . For Model HR2631FT, HR2630T
3 1
2
1.
Set...
HR2631F Instruction Manual - Page 12
... limitation of any trouble develop during this manual. MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy
Every Makita tool is thoroughly inspected and tested before attempting to you . If inspection shows the trouble is caused by small metal dust or similar. • Empty the dust cup before removing a drill bit. • When using Makita replacement parts. Using the dust...
HR2631F Parts Breakdown - Page 2
... 17.5 PISTON CYLINDER GUIDE PLATE PISTON JOINT COMPRESSION SPRING 14
Q'ty Unit
1 PC. 1 1 PC. 1 PC. 1 PC. 1 PC. 1 1 PC. 0 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 1 PC. 1 PC. 1 PC. 1 1 1 1 PC. 1 1 1 2 PC. 4 PC. 1 1 PC. 1 1 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. Model HR2631F Parts List
A = Standard Equipment...
HR2631F Parts Breakdown - Page 3
... PC. 1 PC. 1 PC. 0 1 PC. 1 PC. 1 PC. 2 PC. 1 PC. 1 PC. 2 PC. 1 PC. 1 PC. 1 PC. 1 1 PC. 1 SET 1 PC. 2 PC. 4 PC. 1 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 2 PC. 1 PC. SOCKET...GUIDE PIN 6 COUNTER WEIGHT TAPPING SCREW 4X30 BAFFLE PLATE FIELD 115V MOTOR HOUSING HR2631F NAME PLATE CLEAR LABEL CARBON BRUSH SET CB-325 (195001-2) BRUSH HOLDER UNIT TAPPING SCREW 3X12 TAPPING SCREW 4X30 HR2631F...
Makita HR2631F Reviews
We have not received any reviews for Makita yet.