Makita XAG17ZU Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XAG17ZU manuals!
Problems with Makita XAG17ZU?
Ask a Question
Free Makita XAG17ZU manuals!
Problems with Makita XAG17ZU?
Ask a Question
Makita XAG17ZU Videos
Makita Cordless Brushless Angle Grinder - XAG17ZU
Duration: 7:32
Total Views: 19,691
Duration: 7:32
Total Views: 19,691
Popular Makita XAG17ZU Manual Pages
XAG16/XAG17 Instruction Manual - Page 2
...Specifications may differ from heat, oil, sharp edges or moving parts.
Use of any other similar medical devices should contact the maker of electric shock.
6. Save all safety warnings, instructions, illustrations and specifications... development, the specifications herein are subject...cause you install optional wheel...Read all warnings and instructions for outdoor use any ...all instructions ...
XAG16/XAG17 Instruction Manual - Page 6
....
11.
Be careful not to disposal of your eyes, rinse them out with Makita tools.
4. by Makita. volts
direct current
rated speed
revolutions or reciprocation per minute
Important safety instructions for tool. Overcharging shortens the battery service life.
3. Important safety instructions for a long period (more detailed national regulations. Never recharge a fully charged battery...
XAG16/XAG17 Instruction Manual - Page 7
...unit. Replace the lid of the wireless unit with the groove in the housing and slip it from the tool.
28.
Installing or ... the button on the front of the slot more than Makita wireless unit into the slot may cause them to the ...installing or removing of the slot clean.
13. Restore the lid if it locks in the supplied case or a static-free container.
25. SAVE THESE INSTRUCTIONS...
XAG16/XAG17 Instruction Manual - Page 14
... Avoid applying too much pressure which causes over bending of wires when using
wire wheel brush.
Installing the wireless unit 2. Thread wire wheel
brush onto spindle and tighten with
broken brush wires.
... function
14 ENGLISH Use of the wireless activation function setting is damaged, or which supports the wireless
activation function The overview of damaged brush could...
XAG16/XAG17 Instruction Manual - Page 15
... lid.
Set the stand...Makita vacuum cleaner supporting the wireless activation function is completely closed.
1. If you pull up the wireless unit. Install the batteries to the tool before installing the wireless unit. Projection 3. NOTICE: When installing...installing the wireless unit. Insert the wireless unit to the instruction manual...part of the lid when removing the wireless unit.
XAG16/XAG17 Instruction Manual - Page 16
Install the wireless unit to the instruction manual of the tool.
1. And then press the wireless activation button on ...Stand-by one by switch
3. Wireless activation button 2.
After registering a tool to "AUTO".
1
1
2
► 1 . Set the stand-by switch
4. Wireless activation lamp
If the vacuum cleaner and the tool are linked successfully, the wireless activation lamps will ...
XAG16/XAG17 Instruction Manual - Page 17
... function.
Waiting for the tool registration.
Pull the switch trigger of the vacuum cleaner is available and the is stopped.
17 ENGLISH In this case, set the stand-by switch on the vacuum cleaner to one vacuum cleaner, the vacuum cleaner may vary depending on the tool.
NOTE: The transmission distance...
XAG16/XAG17 Instruction Manual - Page 18
...wireless activation lamps finish blinking in green and then become red. Wireless activation lamp
18 ENGLISH Wireless activation button 2. Set the stand-by switch
3.
Press the wireless activation button on the tool while the wireless activation lamp on the ...the following procedure when cancelling the tool registration for the vacuum cleaner.
1. Install the batteries to "AUTO".
XAG16/XAG17 Instruction Manual - Page 19
Instead, ask Makita Authorized Service Centers, always using Makita replacement parts for repairs, conduct your own inspection first. The wireless unit is dirty. wireless unit and clean the slot. Set the stand-by switch on the terminal of the wireless unit and/or Gently wipe off dust and dirt on the tool has not been ...
XAG16/XAG17 Instruction Manual - Page 20
... tool registration of the other appliances which generate high-intensity radio waves. Inhalation vent
20 ENGLISH Install the wireless unit correctly. Push the wireless activation button briefly and make sure that the tool is...-by switch on the vacuum cleaner is removed before attempting to the circumstances. Set the stand-by switch on the vacuum cleaner to the vacuum cleaner. More than...
XAG16/XAG17 Instruction Manual - Page 21
...accessories, ask your local Makita Service Center. • Makita genuine battery and charger • Wireless unit (For models with your Makita grinder with any other ...accessories or attachments might present a risk of injury to persons. Lock nut wrench 28
21 ENGLISH If you decide to use your Makita tool specified in this manual...
XAG16/XAG17 Instruction Manual - Page 22
... DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. This Warranty gives you specific legal rights, and you may also have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge. Some states do not allow limitation on how long an implied warranty...
XAG17ZU Parts Breakdown - Page 2
Model XAG17ZU Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
Q'ty Unit
001
629299-4
002
...RING 4 PAN HEAD SCREW M5X16 CAUTION LABEL INNER FLANGE 45B LOCK NUT 5/8-45 XAG17 NAME PLATE TAPPING SCREW 4X18 DUST COVER R MOTOR HOUSING SET RUBBER PIN 6 INC. 41 SWITCH KNOB SWITCH LEVER LEVER TORSION SPRING 2 PIN 2 INDICATOR PANEL COMPLETE SWITCH 1246.3223
1 1 1 ...
XAG17ZU Parts Breakdown - Page 3
.... 49,51 CAP LABEL GRIP 36 COMPLETE 5" GRINDING WHEEL 125X6X22 LOCK NUT WRENCH 28 WIRELESS UNIT SET WHEEL COVER 125CKL ASSEMBLY O RING 4 PAN HEAD SCREW M5X16 CAUTION LABEL CAUTION LABEL
1 2 PC. 0 1 1 PC. 1 1 1 PC. 1 1 PC. 1 0 1 1 PC. 1 PC. ... C10 213009-5
A05 C20 265180-1
A05 C30 813N68-9
E01
805C42-5
MOTOR HOUSING SET RUBBER PIN 6 INC. 33 DUST COVER L TERMINAL SUB CONTROLLER XAG17 SERIAL NO.
XAG17ZU New Tool Flyers English - Page 1
..., enabling the BL™ Motor to run cooler and more efficiently for longer life
• Variable speed control dial allows manual RPM adjustment (3,000-8,500) to match the speed to the application
SPECIFICATIONS
Wheel Diameter 5" Battery 18V LXT® Lithium-Ion No Load Speed (variable speed 3,000 - 8,500 RPM Spindle Thread 5/8" - 11...
Makita XAG17ZU Reviews
We have not received any reviews for Makita yet.