Makita XCU02PT Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XCU02PT manuals!
Problems with Makita XCU02PT?
Ask a Question
Free Makita XCU02PT manuals!
Problems with Makita XCU02PT?
Ask a Question
Popular Makita XCU02PT Manual Pages
Makita DC18RD Instruction Manual - Page 3
...manual contains important safety and operating instructions...guide of charger. Do not charge battery cartridge when room temperature is charged at the same time. 1. At cold temperature, charging may burst causing personal injury and damage. 4. Do not insert a nail, wire, etc. Charging light will come out to which is damaged, ask Makita authorized
service center to replace...SPECIFICATIONS
Model...
Makita DC18RD Instruction Manual - Page 4
... cartridge that case, yellow light lights up. 1. Charging will begin after the cooling fan installed in this action makes the melody sound change the melody sound of charge. (In selected ... requires "conditioning charge" to cold air. Trouble on battery is selected, no sounds come out.) 6. Over-discharge of battery (continue to repair or maintenance, if the yellow warning light ...
XCU02Z Instruction Manual - Page 2
... Damaged or entangled cords increase the risk of guide bar
300 mm (12")
Guide bar part No
165245-8
Guide bar type
Sprocket nose bar
Type
90PX
Saw chain... (Original instructions)
SPECIFICATIONS
Model
XCU02
Chain speed
8.3 m/s (500 m/min) (1,650 ft/min)
Length of electric shock. 8. Work area safety 1. Electrical Safety 4. Stay alert, watch what you to change without guide bar)...
XCU02Z Instruction Manual - Page 3
...a qualified repair person using only identical replacement parts. If...parts of injury and fire. 26. Follow instruction for misalignment or binding of personal injury and should never be controlled with specifically designated battery packs.
Always hold the chain saw is not in use and care 24. A wrench or a key left hand on . Use of dust collection can be repaired...serviced by ...
XCU02Z Instruction Manual - Page 5
... cartridge in a
container with clear water and seek medical attention right away. SAVE THESE INSTRUCTIONS.
Charge the battery cartridge with product
(gained from repeated use) replace strict adherence
to
disposal of applicable saw chain and guide bar
ENC007-8
IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY CARTRIDGE
1. It may reach or exceed 50 ﾟ C (122 ﾟ F).
7. Do...
XCU02Z Instruction Manual - Page 10
...guide bar rail (see circle in market. • Never use oil including dust and particles or volatile oil. • When pruning trees, use a safe support
(saw chain is screwed in injury to the tool. Check the amount of installing...tank cap
1
2. Otherwise it may cause breakage of saw chain, wear of the guide bar and breakage of saw chain in a clean place free from the oil tank ...
XCU02Z Instruction Manual - Page 11
... the spike a little lower and finish the cut from the bottom, the branch may cause the guide bar to the handle and continue sawing and draw the chain saw back a little; Move the spike ...: Apply light pressure to wobble, resulting in your body.
11 Keep proper footing and
balance at all parts of the bar is operating. • Hold the chain saw firmly with the lower edge, so that...
XCU02Z Instruction Manual - Page 12
...angle as possible. First make the diagonal cut on the side towards which the tree will fall , and guides it. Felling area
A
45o
B B
A
2 1/2
45o
1
006915
Cut wood under tension. This ... of the trunk is rotten.
− Consider the wind speed and direction. 1. When limbing, support the chain saw on the felled trunk when limbing. The work if the wind is hazardous. Then...
XCU02Z Instruction Manual - Page 13
...and diagonally to keep the back cut ; − The chain penetrates the wood with the guide bar cover before attempting to perform inspection or maintenance. • Always wear gloves when performing... gauge (round nose) and the cutting edge.
13 The wood fibers in a MAKITA specialist repair shop. Sharpening the saw chain
CAUTION: • Always remove the battery cartridge and wear
safety...
XCU02Z Instruction Manual - Page 15
...the section titled " Installing or removing saw chain and guide bar. Sprocket
1
2
014715
Always fit a new locking ring when replacing the sprocket. Locking... repairs, any chips and sawdust from the oil tank to empty it under no load to be replaced at...hole by Makita Authorized or Factory Service Centers, always using a slotted screwdriver with the guide bar cover. Remove the battery ...
XCU02Z Instruction Manual - Page 16
... lead to perform the prescribed maintenance work can be recognized only if this work is not described in the instruction manual. Operating time
Item
Chain saw . Check at authorized service center. Saw chain Guide bar
Inspection. Instructions for periodic maintenance
To ensure long life, prevent damage and ensure the full functioning of the chain saw...
XCU02Z Instruction Manual - Page 17
... work correctly. Ask your own inspection first. Adjust the guide bar and saw chain. TROUBLE SHOOTING
Before asking for repairs, conduct your local authorized service center for repair.
They may be included in this manual. Instead, ask Makita Authorized Service Centers, always using Makita replacement parts for its stated purpose.
Recharge the battery cartridge. Release...
XCU02Z Instruction Manual - Page 18
...," AFTER THE ONE YEAR TERM OF THIS WARRANTY. This Warranty gives you specific legal rights, and you may also have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge. Some states do not allow limitation on how long an implied warranty lasts, so...
XCU02Z Parts Breakdown - Page 2
Model XCU02Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part# Description
001
451972-6 FRONT HANDLE
002
266053-1 TAPPING SCREW 4X35
003
265995-6 TAPPING SCREW 4X18
004
643941-3 BRUSH HOLDER CAP
005
CB442 CARBON BRUSH SET CB-442 (195023-2)
006
644514-5 BRUSH HOLDER
007
644513-7 BRUSH HOLDER
008
815R33-8 XCU02 NAME PLATE
009
620306-6 CONTROLLER...
XCU02Z Parts Breakdown - Page 3
...051
455121-7 OIL TANK
052
424326-0 SPONGE SHEET
053
187941-8 HOUSING SET
053 C10 263005-3 RUBBER PIN 6
053 C20 803R62-3 CAUTION LABEL
053... RUBBER PIN 4
071
142235-8 NUT COMPLETE
072
454819-3 NUT COVER
073
196779-0 SPROCKET COVER SET
073 D10
INC. 58-62,66-68,70-72
A01
165245-8 GUIDE BAR
A02
419288-5 CHAIN COVER
A03
196740-7 SAW CHAIN SET
1 0 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC....
Makita XCU02PT Reviews
We have not received any reviews for Makita yet.