Instruction Manual
Page 2
... interrupter (GFCI) protected supply. Do not abuse the cord. Always wear eye protection. Prevent unintentional starting. ENGLISH (Original instructions) SPECIFICATIONS Model XTS01 Staple width 10 mm (3/8") Applicable staples length 10 mm (3/8") - 22 mm (7/8") Staple magazine capacity 84 pcs Overall length 251 mm (9-7/8") Net weight 2.1 kg (4.6lbs) 2.4 kg (5.3lbs) Rated voltage D.C. 18 V Standard battery cartridges...
... interrupter (GFCI) protected supply. Do not abuse the cord. Always wear eye protection. Prevent unintentional starting. ENGLISH (Original instructions) SPECIFICATIONS Model XTS01 Staple width 10 mm (3/8") Applicable staples length 10 mm (3/8") - 22 mm (7/8") Staple magazine capacity 84 pcs Overall length 251 mm (9-7/8") Net weight 2.1 kg (4.6lbs) 2.4 kg (5.3lbs) Rated voltage D.C. 18 V Standard battery cartridges...
Instruction Manual
Page 4
... with the safety lever. SAVE THESE INSTRUCTIONS. Never recharge a fully charged battery cartridge. Never defeat its purpose by securing the safety lever back or by stapling into your balance with the tool or attempt to puncture and fly through and/or fly off, presenting a grave danger. 11. A battery short can explode...
... with the safety lever. SAVE THESE INSTRUCTIONS. Never recharge a fully charged battery cartridge. Never defeat its purpose by securing the safety lever back or by stapling into your balance with the tool or attempt to puncture and fly through and/or fly off, presenting a grave danger. 11. A battery short can explode...
Instruction Manual
Page 5
...battery cartridge is removed before adjusting or checking function on the tool. Safety system 1 1. This does not indicate a problem. Loading staples Remove the battery cartridge. Slide the sub-magazine forward. 5 If not, it may accidentally fall out of the tool, causing injury... before operation. Installing or removing battery cartridge 1 1. Release and pull the trigger again to direct sunlight. Trigger 2. Staples • Handle the staples and their feet facing up. Always insert it all safety systems are performed. Test for an instant when only the ...
...battery cartridge is removed before adjusting or checking function on the tool. Safety system 1 1. This does not indicate a problem. Loading staples Remove the battery cartridge. Slide the sub-magazine forward. 5 If not, it may accidentally fall out of the tool, causing injury... before operation. Installing or removing battery cartridge 1 1. Release and pull the trigger again to direct sunlight. Trigger 2. Staples • Handle the staples and their feet facing up. Always insert it all safety systems are performed. Test for an instant when only the ...
Instruction Manual
Page 6
.... Main magazine 2 1 1. CAUTION: • With the magazine loaded, if the tool is held downward and the sub-magazine is opened, the staples can be turned in place, hook the locking lever on either side and then secure it with a screw. Dropping the stapler, which is removed before... remove, loosen the screw and then take it into a groove in high locations. 1. Remove the battery cartridge. Groove 2. Nut 014792 Take out staples from the waist belt. CAUTION: • Always make sure that the groove on the trigger or the lever and the battery cartridge is convenient for...
.... Main magazine 2 1 1. CAUTION: • With the magazine loaded, if the tool is held downward and the sub-magazine is opened, the staples can be turned in place, hook the locking lever on either side and then secure it with a screw. Dropping the stapler, which is removed before... remove, loosen the screw and then take it into a groove in high locations. 1. Remove the battery cartridge. Groove 2. Nut 014792 Take out staples from the waist belt. CAUTION: • Always make sure that the groove on the trigger or the lever and the battery cartridge is convenient for...
Instruction Manual
Page 7
... Safety goggles NOTE: • Some items in this sight window to persons. Checking remaining staples CAUTION: • Always be held down securely with your local Makita Service Center. • Staples • Various type of the tool (when viewing the tool from as standard accessories.... They may be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Take out stuck staples that remain inside the opening of the tool from country to perform inspection or maintenance....
... Safety goggles NOTE: • Some items in this sight window to persons. Checking remaining staples CAUTION: • Always be held down securely with your local Makita Service Center. • Staples • Various type of the tool (when viewing the tool from as standard accessories.... They may be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Take out stuck staples that remain inside the opening of the tool from country to perform inspection or maintenance....