Instruction Manual
Page 2
...cover of the warning decals. Note: The decals may not be shown at actual size. and are registered trademarks of Wi-Fi Alliance. NORDICTRACK and IFIT are used under license. Wi-Fi is a registered trademark of ICON Health & Fitness, Inc. TABLE OF CONTENTS WARNING DECAL ...PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 5 PART IDENTIFICATION CHART 6 ASSEMBLY 7 THE CHEST HEART RATE MONITOR 13 HOW TO USE THE INCLINE TRAINER 14 HOW TO MOVE THE INCLINE TRAINER 26 MAINTENANCE AND TROUBLESHOOTING 27...
...cover of the warning decals. Note: The decals may not be shown at actual size. and are registered trademarks of Wi-Fi Alliance. NORDICTRACK and IFIT are used under license. Wi-Fi is a registered trademark of ICON Health & Fitness, Inc. TABLE OF CONTENTS WARNING DECAL ...PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 5 PART IDENTIFICATION CHART 6 ASSEMBLY 7 THE CHEST HEART RATE MONITOR 13 HOW TO USE THE INCLINE TRAINER 14 HOW TO MOVE THE INCLINE TRAINER 26 MAINTENANCE AND TROUBLESHOOTING 27...
Instruction Manual
Page 4
... hood unless instructed to do so by an authorized ser- Do not attempt to raise, lower, or move the incline trainer until it is properly assembled. (See ASSEMBLY on page 7, and HOW TO MOVE THE INCLINE TRAINER on the incline trainer. Never insert any object into the off position (see the drawing...
... hood unless instructed to do so by an authorized ser- Do not attempt to raise, lower, or move the incline trainer until it is properly assembled. (See ASSEMBLY on page 7, and HOW TO MOVE THE INCLINE TRAINER on the incline trainer. Never insert any object into the off position (see the drawing...
Instruction Manual
Page 6
Note: If a part is not in parentheses below to see whether it is preattached. Extra parts may be included. 3/8" Star Washer (3)-12 5/16" x 3/4" Patch Screw (108)-4 #8 x 5/8" Machine Screw (106)-6 3/8" x 5 1/2" Screw (1)-4 6 The number in the hardware kit, check to identify small parts used for assembly. The number following the key number is the quantity used for assembly. PART IDENTIFICATION CHART Use the drawings below each drawing is the key number of the part, from the PART LIST near the end of this manual.
Note: If a part is not in parentheses below to see whether it is preattached. Extra parts may be included. 3/8" Star Washer (3)-12 5/16" x 3/4" Patch Screw (108)-4 #8 x 5/8" Machine Screw (106)-6 3/8" x 5 1/2" Screw (1)-4 6 The number in the hardware kit, check to identify small parts used for assembly. The number following the key number is the quantity used for assembly. PART IDENTIFICATION CHART Use the drawings below each drawing is the key number of the part, from the PART LIST near the end of this manual.
Instruction Manual
Page 7
Do not dispose of the packing materials until assembly is completed. If 1 you finish all parts in a cleared area and remove the packing materials. If there is normal. This is an oily substance on ... screwdriver • After shipping, there may be an oily substance on the exterior of the incline trainer. ASSEMBLY • Assembly requires two persons. • To identify small parts, see page 6. • Place all assembly steps. • Assembly requires the following information to the email address or postal address on the front cover of this...
Do not dispose of the packing materials until assembly is completed. If 1 you finish all parts in a cleared area and remove the packing materials. If there is normal. This is an oily substance on ... screwdriver • After shipping, there may be an oily substance on the exterior of the incline trainer. ASSEMBLY • Assembly requires two persons. • To identify small parts, see page 6. • Place all assembly steps. • Assembly requires the following information to the email address or postal address on the front cover of this...
Instruction Manual
Page 10
Attach the right handrail assembly (D) in the same way. 108 108 D 109 C 7. Do not overtighten the Machine Screws. 106 106 106 E 110 10 Attach the Push Bar Bottom 6 (109) with six #8 x 5/8" Machine Screws (106); start all six Machine Screws, and then tighten them. do not fully tighten the Patch Screws yet. Set the handrail assembly (E) on the floor in the position shown. Attach the Push Bar Top (110) 7 with two 5/16" x 3/4" Patch Screws (108); 6 Set the left handrail assembly (C) on the floor in the position shown.
Attach the right handrail assembly (D) in the same way. 108 108 D 109 C 7. Do not overtighten the Machine Screws. 106 106 106 E 110 10 Attach the Push Bar Bottom 6 (109) with six #8 x 5/8" Machine Screws (106); start all six Machine Screws, and then tighten them. do not fully tighten the Patch Screws yet. Set the handrail assembly (E) on the floor in the position shown. Attach the Push Bar Top (110) 7 with two 5/16" x 3/4" Patch Screws (108); 6 Set the left handrail assembly (C) on the floor in the position shown.
Instruction Manual
Page 11
...Upright Cover (not shown) as shown. start all four Screws, and then tighten them. G 71 11 Then, move both sides of the handrail assembly between the Console (93) and the Console Base (92). Then, press the Right Outside Upright Cover (71) against the lower end of a ...second person, position the handrail assembly (E) below the Console (93) 8 as described above. rail assembly upward at the same time, sliding the inner corner (F) of the hand- Next, attach the handrail...
...Upright Cover (not shown) as shown. start all four Screws, and then tighten them. G 71 11 Then, move both sides of the handrail assembly between the Console (93) and the Console Base (92). Then, press the Right Outside Upright Cover (71) against the lower end of a ...second person, position the handrail assembly (E) below the Console (93) 8 as described above. rail assembly upward at the same time, sliding the inner corner (F) of the hand- Next, attach the handrail...
