Oki OKIPOS 441 ParallelBlack Support and Manuals
Get Help and Manuals for this Oki Data item
View All Support Options Below
Free Oki OKIPOS 441 ParallelBlack manuals!
Problems with Oki OKIPOS 441 ParallelBlack?
Ask a Question
Free Oki OKIPOS 441 ParallelBlack manuals!
Problems with Oki OKIPOS 441 ParallelBlack?
Ask a Question
Popular Oki OKIPOS 441 ParallelBlack Manual Pages
Users Guide - Page 2
...é par le ministère des Communications du Canada. However, should any errors be detected, OKI would greatly appreciate being informed of them. • The above statement applies only to printers marketed in EU. For compliance with the instruction manual, may cause harmful interference to press. This equipment generates, uses and can assume...
Users Guide - Page 3
...the Printer 7 4-3. Loading the Ribbon Cartridge and Paper 15 5-1. Control Panel and Other Functions...21 6-1. Errors...22 6-4. Dip Switch Setting...38 10-1. Ethernet Interface Model...41 10-5. Interface Specifications...45 11-2. Unpacking and Installation...2 2-1. Connecting the Cable to a Peripheral Unit 11 4-5. Control Panel...21 6-2. Preventing and Clearing Paper Jams...
Users Guide - Page 28
... Near End Sensor Adjustment Mode is entered by releasing the FEED switch after the buzzer sounds five times. (Refer to the separate Specifications Manual for details.) (Holding down for 2 more seconds)
(6) The Memory Switch Manual Setting Mode is entered by releasing the FEED switch after the buzzer sounds six times. (Refer to the separate...
Users Guide - Page 38
...To drive them continu- ously, set the duty cycle ratio to the separate Specifications Manual for coils L1 and L2 is...model: RMB-24
Voltage rating: 24V
Average consumption current: Max. 21 mA (at 24V)
Sound pressure:
Min. 75 dB at 1 m
Lead wires:
red (+) black (-)
3.
Refer to the separate Specifications Manual for details
on commands.
4. Refer to the separate Specifications Manual...
Users Guide - Page 42
... become effective when the power switch is turned off before changing the settings.
The new settings take off the DIP switch cover, as shown
in the table below . Set the switches using a pointed tool, such as given in the illustration below . Replace the DIP switch cover. Then take effect when you turn on DIP...
Users Guide - Page 43
A mechanical error will occur.
*2 USB interface model only *3 Do not change the default setting (Switch 1-8 = off )
Note: Do not enable the auto cutter for enabling/disabling the auto cutter are as follows. Models without the auto cutter (i.e., models with auto cutter: Valid (Switch 1-2 = off ).
- 39 - n DIP switch
SW No. 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8
Function Always ON Auto Cutter ...
Users Guide - Page 44
...screws. 3. Remove the serial interface board unit. 4.
Then secure it . 2. 10-1. Replace the serial interface board unit. Switch 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8
Function
DIP-... to change the communication settings. RS-232C Interface Model
The RS-232C interface model is equipped with the screws. 6. ON
OFF No. 1 2 3 4 5 6 7 8
DIP-SW2
DIP switch 2
The factory settings of the DIP switches....
Users Guide - Page 45
... recognized as described below to initialize the setting information. Ethernet Interface Model
n Initializing Settings Set the push switch as 100BASE-TX. After the interface board has been initialized, the printer will return the settings of the red and green LEDs. Red : Lights when packets are received. LED
Push switch
- 41 - Push the switch for one...
Users Guide - Page 46
Wireless LAN Interface Model
DIP-SW 2
Switch 2-1 2-2
ON Fixed at OFF
Initialize of DIP switch are received. LED ... contains a built-in wireless device and can only be used in the following
countries.
Change DIP Switch 2-2 to ON to initialize the setting information when the power is turned on. USA, UK, France, Ireland, Belgium, Germany, Austria, Switzerland, Italy, Denmark, Norway, Sweden...
Users Guide - Page 53
...." For interfacing, signal lines should always use twisted pair cables with an Amphenol 57-30360 connector
Parallel interface connector (printer side)
- 49 - For instructions on setting the memory switch, please refer to the separate Specification Manual. 4. To get the device ID, change memory switch 6-C to the signal ground level. 3. munication fails. 2. For...
Users Guide - Page 55
... EEPROM. 14. For details on the functions and settings of memory switches, see the separate Specification Manual.
The table below shows the factory settings for the memory switches. Memory Switch 0 1 2 3 4 5 6 7 8 9
Hexadecimal Code 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
WARNING
Changing the memory switch settings can cause the printer to fail to operate...
Software Manual - Page 4
... Connection 11 Uninstalling the Driver Software from Windows 2000 and XP . . . . . 16
Installing the Driver Software on Windows Vista 18 For USB Connection 18 For Parallel Port (LPT1) Connection 20
Software Features 26 OKIPOS 441 Setup Utility 26 Port Emulator 26
Windows 2000/XP/Vista Printer Driver Settings 27 Setting the Printer 27 Setting the Paper Type 28...
Software Manual - Page 10
...printer connected.) If the printer is displayed, the installation is finished.
10 • Installing Software, Windows 2000 and Windows XP Setting up the Connection:
> For USB Connection, see...manual, click Document at the bottom right of the Windows desktop to indicate that the actual display will vary according to the specific type of the printer hardware and automatically installs the driver...
Software Manual - Page 26
...Setup Utility
The OKIPOS 441 setup utility provides an easy way • to set up a virtual serial port, making it possible for applications that this feature. This utility is not supported on Windows versions prior to set... connection. Port Emulator
This feature sets up an Ethernet interface card. Note that support only serial printers to select the utility only without also installin the...
Software Manual - Page 49
... Size
This driver supports both standard sizes and user-defined sizes.
Standard Sizes
The following standard sizes are using 57.5 mm-wide paper rolls, for margins. If you wish to Receipt
49 • Windows 2000/XP/Vista Printer Driver Settings Setting
Default Widtha
Length
45 mm × 200mm
45 mm
200 mm
45mm × Receiptb...
Oki OKIPOS 441 ParallelBlack Reviews
We have not received any reviews for Oki yet.