Oki OKIPOS T410DT-Parallel Support and Manuals
Get Help and Manuals for this Oki Data item
View All Support Options Below
Free Oki OKIPOS T410DT-Parallel manuals!
Problems with Oki OKIPOS T410DT-Parallel?
Ask a Question
Free Oki OKIPOS T410DT-Parallel manuals!
Problems with Oki OKIPOS T410DT-Parallel?
Ask a Question
Popular Oki OKIPOS T410DT-Parallel Manual Pages
Quick Guide - Page 7
... number represents the reason of the error. See the manual for used by service personnel.
■ DIP-SW Appropriate settings are set in the Printer Setting screen. See the manual for details.
■ Error number display .. Do not use this. See the manual for details.
■ Sensor level ...... When the error light is set according to your printer
system environment. ■...
Quick Guide - Page 13
Confirm that the head is detached from the platen roller part, then lift the head in the direction as shown in the Figure.
3 While ...direction of the ribbon core in Figure. Insert the guide part of the roll. While depressing the mark on the opposite side. And insert the empty ribbon core to the unit.
11 Ribbon Setting
Thermal Transfer model OKI POS T400/T410 only.
1 Confirm the [PUSH]...
Quick Guide - Page 15
... head using the Cleaning Kit. ➞ If a label is adhered to the manual) by changing the printer darkness settings in your computer.
• Setting of the software in the Printer Setting screen. Does not print correctly
Print error
• Paper set correctly? ➞ Please set the paper correctly.
• Platen roller clean? ➞ If the platen roller...
Quick Guide - Page 16
... manual for details.
14 No label is adhered to the head? ➞ If the thermal head is not clean, clean the head using the Cleaning Kit. ➞ If a label is adhered to the thermal head, clean it by using metal instruments such as a screw driver. Confirm the error number that the paper is set...
Users Guide - Page 4
.... PREFACE
OKIPOS T400/T410 USER'S GUIDE
OKIPOS T400/T410 USER'S GUIDE contains basic information about the printer such as setup, installation, cleaning and maintenance. It also contains complete instructions on how to unpack and set up the printer, load the labels and ribbon, and how to use the operator panel to the host system. SECTION 1. SECTION 3. SECTION 5. TROUBLESHOOTING This...
Users Guide - Page 10
...Manual...solution for those command codes. The T400 and T410 share the same command set, the only difference ... such as setup, installation, configuration, cleaning and maintenance. There are specified in this section:
• General Printer Specifications •.... It probably will vary depending on the label.
The OKIPOS T400/T410 printers use a subset of the different printer ...
Users Guide - Page 19
...Consider the following materials when unpacking:
10
In addition to reach room temperature before applying power. • Set the printer on a solid flat surface. Inspect the shipping container and printer for any signs of damage ... their protective containers. • If the printer has been stored in a cold environment, allow it to this manual, verify that you have occured during shipping.
Users Guide - Page 38
... rear. 2. The printer will then beep3
times indicating it is pressed, suspending the print operation. To remove the printer from the Factory/Service Print Test mode, remove power by one containing the internal printer settings. Press the LINE and FEED keys while simultaneously turning the POWER switch to print a small (2" wide) Factory...
Users Guide - Page 47
...The examples given in this manual are printed on separate lines because they are the special control characters that a command code will follow Cutter command (Responds...The Standard Protocol Control codes are nonprintable characters, and the Non-Standard Protocol Control codes are two pre-defined different sets of Protocol Control codes to receive instructions. CONTROL CHARACTER
SOH STX...
Users Guide - Page 76
... for more information.
2. When using a OKI cutter unit with two labels between each cut value and the print quantity.
67 A H0020V0020XB1ABCQ3 ~0002 Z
This set of commands will print 6 labels (3 x 2) ...labels printed is inactive.
4. If the cutter option has been enabled in this section manual.
3.
Cut Job
Command Structure
Command Function Input to Printer: Printer Output:
aaaa ~aaaa...
Users Guide - Page 122
...Not currently supported 6 Reader programming 9 digit numeric Postal Code 3 digit numeric Country Code 3 digit numeric Service Class ...Codes Maxicode
Command Structure
Command Function Command Function Printer Output
BVa,b,c,ddddddddd,eee,fff,gggg.....
UPS shipments 3 For Mode 3 Structured Carrier Message
for specific information on a label. Total number of Maxicode symbol within the set...
Users Guide - Page 123
Special Notes
1. The following modes are supported. MODE POSTAL CODE
2
9 digits max
numeric only
3
6 digits fixed
alphanumeric
4
"000000"
6
fixed data
COUNTRY CODE
3 digits max numeric only
3 digits max numeric only
"000" fixed data
SERVICE CLASS
3 digits max numeric only
3 digits max numeric only
"000" fixed data
MESSAGE LENGTH
84 characters alphanumeric
84 characters alphanumeric...
Users Guide - Page 142
...parallel interface or the optional USB interface. X-On/X-Off FLOW CONTROL
X-On/X-Off flow control is used whenever hardware (Ready/Busy) flow control is installed, the printer can be capable of supporting this flow control method for receipt of data. When it is placed back on line manually... driver are transmitted by the printer on the printer for Ready/Busy flow control. When the error is...
Users Guide - Page 159
...
commands (B, BD, and D).
g = Mirror image
0 Normal Print
1 Reverse Print
hh = Guide cell thickness (01-15) 01 indicates normal type. specification.
113
ddddddddd,
a = Position of symbol within the set
c = Mode
dd..d = 9 digit numeric Postal Code
eee = 3 digit numeric Country Code
f f f = 3 digit numeric Service Class
gg..g = Data, terminated by dot (004-600 dots)
BXaabbccdd...
Users Guide - Page 188
... Q001Z
179
Total number of Maxicode symbols in the set , when used in a structured append format 1~8. UPS shipments 3 For Mode 3 Structured Carrier Message
for International UPS shipments 4 Standard symbol 5 Not currently supported 6 Reader programming 9 digit numeric Postal Code 3 digit numeric Country Code 3 digit numeric Service Class Data, terminated by
Notes Example
MODE POSTAL...
Oki OKIPOS T410DT-Parallel Reviews
We have not received any reviews for Oki yet.