Oki OKIPOS 407II SerialBlack Support and Manuals
Get Help and Manuals for this Oki Data item
View All Support Options Below
Free Oki OKIPOS 407II SerialBlack manuals!
Problems with Oki OKIPOS 407II SerialBlack?
Ask a Question
Free Oki OKIPOS 407II SerialBlack manuals!
Problems with Oki OKIPOS 407II SerialBlack?
Ask a Question
Popular Oki OKIPOS 407II SerialBlack Manual Pages
Users Guide - Page 2
..., if not installed and used in accordance with the instruction manual, may cause harmful interference to printers marketed in U.S.A. For compliance with the limits for radio noise emissions from digital apparatus set out in a commercial environment.
The above statement applies only to radio communications.
Reproduction of any part of this manual in any errors in this equipment...
Users Guide - Page 3
......35 10-2. Black mark specifications...39
11. Dip Switch Setting...40 11-1. USB Interface Model...46 Unpacking and Installation...1 1-1. Turning Power On...10 3-6. Attaching the Holder Plate...17 4-2. Consumable Parts and AC Adapter...20 5-1. Thermal Paper Roll...20 5-2. AC adapter (option)...27
6. Control Panel and Other Functions...28 6-1. Errors...28 6-3. Cleaning the Sensors...
Users Guide - Page 4
...and Wireless LAN Interface 57 14-1. USB Interface Specifications...57 14-2. Interface Specifications...53 13-2. Ethernet Interface Specifications 57 14-3. Ethernet Interface Model...47 11-5. Electrical Characteristics...56
14. Wireless LAN Interface Specifications 57
15. RS-232C Serial Interface...53 13-1. 11-4. Memory Switch Settings...60 Wireless LAN Interface Model 48
12.
Users Guide - Page 18
... case, change to the separate Specifications Manual. 3-7-2.
Then, lower the adjustment lever to the position in which the protrusion on setting the memory switch, refer to a paper roll with a 57.5 mm width, remove the paper roll holder, and install the paper roll holder into the other groove. For instructions on the adjustment lever engages with...
Users Guide - Page 25
...the separate programmer's manual for printing darkness... thickness of the paper, it may not be necessary to scan a printed bar code or characters depending on the type of Print Columns (12 ×24 Font)
48...33
Left Margin
Effective Print Width
Right Margin
Paper Width
- 21 -
To change the settings for details.
2) The print density may vary depending on the print density. Make sure...
Users Guide - Page 26
... scan a printed bar code or characters depending on the type and thickness of the paper, it may be necessary to change the darkness settings, use paste or glue to scan correctly beforehand.
- 22 - Refer to the separate programmer's manual for printing darkness. Full-Face Thermal Label Paper Roll
(1) Label paper specification
Backing paper width...
Users Guide - Page 28
...to change the darkness settings, use the printing darkness settings command 'd'n. Refer to the separate programmer's manual for printing darkness....settings for details.
2) The print density may vary depending on the print density. Adhesion type
High adhesion
High adhesion
High adhesion
Note:
1) Depending on the type and thickness of the paper, it may not be able to scan a printed bar code...
Users Guide - Page 36
... memory switch A may be
some variances depending on the vertical/wall-mount lay-
Therefore, set at level 1 on the horizontal
layout and level 3 on the rolled state of the
... vertical
B
(wall-mount) layouts. mm)
(Approx. For instructions on setting the
memory switch, refer to the separate Specifications
Manual.
3) The detected diameter and remained paper length
A
given above...
Users Guide - Page 44
... again. 11.
The following is set the power switch to change the settings. Replace the DIP switch blind. The new settings take off before changing the settings. Be sure to set to on DIP switches. 1. Make sure the printer is recommended to use a pointed item like a pen or flat-blade driver screw to off the DIP switch...
Users Guide - Page 45
Parallel Interface Model
ON
ON
OFF No. 1 2 3 4 5 6 7 8 9 10
DIP-SW 1
OFF No. 1 2 3 4
DIP-SW 2
Switch 1-1 ON OFF
DIP-SW 1
The factory settings of switches 1-2 through 1-10 will change according to the command emulation that has been set using switch 1-1.
(1) Star mode
Switch
Function
1-1
Command emulation
1-2
Should not be changed (Should be set to on)
1-3
Should...
Users Guide - Page 47
... Receive buffer full Valid Valid
OFF 180 DPI Valid Receive buffer full Valid Valid
- 43 - RS-232C Interface Model
ON
ON
OFF No. 1 2 3 4 5 6 7 8 9 10
DIP-SW 1
OFF No. 1 2 3 4
DIP-SW 2
Switch 1-1 ON OFF
DIP-SW 1
The factory settings of switches 1-2 through 1-10 will change according to the command emulation that has been...
Users Guide - Page 50
... are all on
- 46 - 11-3.
USB Interface Model
ON
OFF No. 1 2 3 4 5 6 7 8 9 10
DIP-SW 1
ON
OFF No. 1 2 3 4
DIP-SW 2
Switch 1-1 1-2 1-3 1-4 1-5 1-6
1-7 1-8 1-9 1-10
DIP-SW 1
Function Command emulation (Ster Line mode) Should not be changed (Should be set to on) Should not be changed (Should be set to on) Sensor adjustment USB mode Handshaking conditions...
Users Guide - Page 51
...
Invalid Offline or receive buffer full
Invalid
OFF
Valid Receive buffer full Valid
Switch 2-1~2-4
Function Always ON
DIP-SW 2
The factory settings of DIP switch are all on. Ethernet Interface Model
ON
OFF No. 1 2 3 4 5 6 7 8 9 10
DIP-SW 1
ON
OFF No. 1 2 3 4
DIP-SW 2
Switch 1-1 1-2 1-3 1-4 1-5 1-6
1-7 1-8 1-9 1-10
DIP-SW 1
Function Command emulation (Ster Line mode...
Users Guide - Page 52
...Model
ON
ON
OFF No. 1 2 3 4 5 6 7 8 9 10
DIP-SW 1
OFF No. 1 2 3 4
DIP-SW 2
Switch 1-1 1-2 1-3 1-4 1-5 1-6
1-7 1-8 1-9 1-10
DIP-SW 1
Function Command emulation (Ster Line mode) Should not be changed (Should be set to on) Should not be changed (Should be set...described below to their default, or ex-factory, settings. ■ Initializing Settings Set the push switch as 100BASE-TX. After that...
Users Guide - Page 64
For details on the functions and settings of memory switches, see the separate Specification Manual. Memory Switch 0 1 2 3 4 5 6 7 8 9
Hexadecimal Code 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
WARNING
Changing the memory switch settings can cause the printer to fail to operate correctly.
- 60 - 16. Memory Switch Settings
Each memory switch is stored in EEPROM. The...
Oki OKIPOS 407II SerialBlack Reviews
We have not received any reviews for Oki yet.