Sanyo PLC-XM100 Support and Manuals
Get Help and Manuals for this Sanyo item
View All Support Options Below
Free Sanyo PLC-XM100 manuals!
Problems with Sanyo PLC-XM100?
Ask a Question
Free Sanyo PLC-XM100 manuals!
Problems with Sanyo PLC-XM100?
Ask a Question
Most Recent Sanyo PLC-XM100 Questions
Xm100 Lamp Timer Reset
Is it possible to reset the lamp pcd ona Sanyo xm100.
Is it possible to reset the lamp pcd ona Sanyo xm100.
(Posted by Anonymous-55567 12 years ago)
Xm100 Lamp Timer Reset
Is it possible to reset the lamp pcd ona Sanyo xm100.
Is it possible to reset the lamp pcd ona Sanyo xm100.
(Posted by Anonymous-55564 12 years ago)
Popular Sanyo PLC-XM100 Manual Pages
Network Setup - Page 1
The safety instructions in the owner's manuals should be followed strictly. First, read the owner's manual of the projector and the safety instructions. Read this manual thoroughly to understand the basic operation of the projector to operate the Network function. Owner's Manual
Network Set-up and Operation
Wired Setting Projector Set-up and Operation
This is the manual for the Network ...
Network Setup - Page 2
...the user is connected.
- fied in a residential installation. able protection against harmful interference in the instructions....Part 15 of
FCC Rules.
Do not make any changes or modifications to provide reason- These limits are designed to the equipment unless otherwise speci- Model Numbers
: PLC-XM100, PLC-XM100L, PLC-XM150, PLC-XM150L
Trade Name
: Sanyo
Responsible party
: SANYO...
Network Setup - Page 4
... instructions...3 Table of contents...4
Chapter 1 Preparation 5
Features...6 Required operating environment for computers 7 Network specifications of the projector...7 Flow of installation...9
Chapter 2 Setup Procedures 11
Connecting to the LAN line...12 Network configuration...12 Network PIN code...14 Network information...14 Network factory default...15 Wired LAN factory default settings...
Network Setup - Page 12
... is sending or receiving the data. When installing, consult your system administrator to the LAN connection terminal of the projector. LAN Connection Terminal
ACT Lamp (Orange) Blink orange when the projector is connected to "3.
Select "Network" in "3. Basic setting and operation." Chapter 2 Setup Procedures
Setting procedures and contents differ depending on or blink, and after...
Network Setup - Page 13
... use the function E-mail alert.
13 Normally sets 255.255.255.0
Gateway*2 Sets IP address of the default gateway (Router)
DNS*3 Sets IP address of the projector
Subnet Sets Subnet mask. When it is available on your system administrator about the detailed settings. Select "Network setting" in a row where you setup the network setting manually, select "Off". After completing all...
Network Setup - Page 20
... click Set button.
✐ The value in the text box indicates current value. ✐Each item has a valid setting range. In this manual. The setting value exceeding this becomes invalid. Some con- Example of those items are indicated with "---".
20
Chapter 3 Basic Setting and Operation
How to use the setting page
To control and set up the projector...
Network Setup - Page 23
... PJLink Standard Class 1 of model or brand, for the password. PJLink and password setting
This is to set the Network PIN code to restrict the access from an unauthorized person through the network. The default Network PIN code [0000] means no Network PIN code is set.
✐ W hen you connect the projector to the network, it supports all commands defined by...
Network Setup - Page 27
... accumulation.
● When PJ needs service:
TITLE: Message from projector Projector Model Name: model name TCP/IP: 192.168.1.201 Projector Name: Proj05
It sends you following message.
*The Projector lamp is turned off , because the projector power circuit failed.
Administrator or user can take an efficient action quickly by receiving this message. Error information
MAIN, 3.3V NG...
Network Setup - Page 28
... will not be sent when unchecking the mail sending condition "When PJ lamp replacement time is sent to users in every poweron of the projector. Chapter 3 Basic Setting and Operation
● When PJ lamp replacement time is reached:
TITLE: Message from projector Projector Model Name: model name TCP/IP: 192.168.1.201 Projector Name: Proj05 It sends you following message. *The accumulated...
Network Setup - Page 33
... inside the projector.
If you set on the projector, you turn on /off . Projector is turned off the projector via the networks, preset the projector as follows: 1. Check up LED status of the projector. When a security (PIN code lock) has been set this function as "Network". Select "Setting" from the Setting menu and set this as Eco, then the network part will be...
Network Setup - Page 41
... not reset the Filter counter when the filter cartridge is not replaced. Value, PJ time, Network PIN code, Network setting
* This function is disabled after filter cartridge replacement. Filter control........Scroll the filter. Filter warning.....Sets the time to indicate the filter warning message on the screen. (OFF, 400H, 700H, 1000H)
PJ lock
suspend When the projector...
Network Setup - Page 49
.... If you do not set up
C0A
Volume down
C0B
Audio Mute on
C0C
Audio Mute off
C1C
Menu display on
C1D
menu display off
*1 F urther instructions about the telnet application, please see the on-line guide on the Keyboard.
> close [return]
The table below table, to control the projector and then press "Enter...
Network Setup - Page 52
... accessing the projector installed in the proxy settings window.
Chapter 5 Appendix
Proxy setting Select Internet Options from the local area network, check the item Use a proxy server and enter the proxy server address and port correctly in the local area network, enter the IP address or domain name here.
52 For further instruction please consult...
Network Setup - Page 53
... the proxy server when accessing the projector installed in the proxy setting window. Netscape Navigator v.7.1
JavaScript Setting Select Preference from Edit menu on the web browser and then select the item Advanced/Scripts & Plugins in the Category column. For further instruction please consult your web browser's the proxy server set up your network administrator.
-
Using proxy...
Network Setup - Page 54
... to configure. Using proxy server To use the proxy server when accessing the projector installed in Web Proxy Server window. For further instruction please consult your web browser Safari's the proxy server set up your network administrator. - To designate proxy settings that will not use an external internet connection from Safari menu on the web...
Sanyo PLC-XM100 Reviews
We have not received any reviews for Sanyo yet.