Uniden QT206 Support and Manuals
Get Help and Manuals for this Uniden item
View All Support Options Below
Free Uniden QT206 manuals!
Problems with Uniden QT206?
Ask a Question
Free Uniden QT206 manuals!
Problems with Uniden QT206?
Ask a Question
Most Recent Uniden QT206 Questions
How To Fix Problem With My Depth Finder Noise Part Of The Alarm??
I was out boating a few weeks ago and we went over a pretty decent size wake from another boat and s...
I was out boating a few weeks ago and we went over a pretty decent size wake from another boat and s...
(Posted by gregsteva7 1 year ago)
Red Wire Goes To Ignition Switch. Where Does The Black (with Red Stripe) Wire Go
(Posted by Acer2b2 2 years ago)
Qt206 Alarm
My boat is sitting on my trailer and I would like to know when the depth finder is on the alarm soun...
My boat is sitting on my trailer and I would like to know when the depth finder is on the alarm soun...
(Posted by billhudson2000 2 years ago)
Where Can I Buy A Uniden Qt-206?depth Finder? Need To Replace Old Unit
I would like to replace the old broken unit on my boat. Where can I buy 1
I would like to replace the old broken unit on my boat. Where can I buy 1
(Posted by Randy44m 6 years ago)
Is The Unidentqt The Same As Impulse Qt 206
(Posted by Billiedrake 8 years ago)
Popular Uniden QT206 Manual Pages
English Owners Manual - Page 3
Contents
Unpacking 2 Features 2 Installing the QT 206 3 Transducer Wiring 4 Power Cable Wiring 4 Installing The Transducer 5
Transom Mount Transducers 5 Through-the-hull Transducers 8 Low Profile Transducers 9 Stem-type (power Boat Bronze) Transducers 10 Inside-the-hull Transducers 12 Understanding Sonar 14 Air Echoes 14 Setting The Shallow Water Alarm 15 Shallow Water Sensitivity ...
English Owners Manual - Page 4
...Night Viewing -
FEATURES
n Depth Readings - UNPACKING
Your QT-206 Depth Sounder box should contain the following items: • Transducer with a soft glowing lamp designed to help your dealer immediately. The QT-206 is back lit at all times with 3 lugs attached • Power Cable (attached to the gauge) • Mounting Bracket and hardware • This Operating Guide
If any items are...
English Owners Manual - Page 5
... BRACKET WASHER
P/N: 950-025
P/N: 308-029
X-ducer Red Black Shield
Alarm
More
Less
Shallow
Sensitivity
Power
+
3 Look at the front of the dash panel.
6. INSTALLING THE QT-206
1. Find a location on the shaft. Test fit the unit in the hole, and make any cables or wiring which will provide clear viewing and access...
English Owners Manual - Page 6
... power cable directly to a power source which will need these female lugs, contact your Uniden Marine dealer. Another method for a depth sounder so that when you turn the unit on , the depth sounder immediately starts working. When shipped from the factory, the transducer is connected to either the RED, BLUE, or WHITE wire.
Some boats have...
English Owners Manual - Page 9
... consistent performance. Transducer Replacement/Identification Tag
On most transducers manufactured after 1987, the operating frequency and part number is attached...the bracket to lower the transducer further into the transom. Do not remove the connector...wiring. Route the cable to the QT-206, being careful not to operate improperly.)
Transducer Wetting
Immediately before launching your vessel, ...
English Owners Manual - Page 10
... cost, and more complete seal to varying degrees.
Larger fiberglass boat manufacturers often request bronze transducers and fittings due to read improperly and cause erroneous readings. However, nylon transducers are 1-3/4" or 2" in the installation. However, some solvent bases will cause the instrument to the size of the boat and the total number of material depends...
English Owners Manual - Page 14
... has no entrapped air. Selecting an Installation Location
The transducer should conduct sound at speeds close to that of the plastic or epoxy face of the transducer and the polyester resin of hull. Epoxy adhesives, as the crystal is designed to ensure optimum instrument results. Generally, best operation is obtained by mounting the Inside...
English Owners Manual - Page 15
...against the hull, pressing the transducer face against the hull. Mix the two-part epoxy supplied with a screwdriver to the hull will eventually cause improper readings.
13 The working time of... and false readings can 't be 60° or higher for at this point, the depth sounder should now operate. Coat the face of the transducer with a disc sander until the transducer is physically ...
English Owners Manual - Page 17
... disappear after you see a digital readout proceeded by an "A", this is shallower. Several seconds after you press either alarm key and then will audibly alert you if you enter water shallower than your ALARM setting. When you press either the "UP" or "DOWN" keys, the instrument displays the actual depth reading. The LCD shows an...
English Owners Manual - Page 18
... the first 10 feet of bottom conditions (sandy, rocky, muddy) can affect the readings on your digital depth sounder. It alters the system's response time in either direction could be the same model. Example:
• SHALLOW READINGS: If your instrument occasionally displays random, false shallow readings such as 3.1', 2.8', and 4.3', you may need to adjust this control.
• DEEPER...
English Owners Manual - Page 19
... looking at a time. WHEN TO USE LESS SENSITIVITY: SHALLOW READINGS Use less sensitivity when your instrument displays a series of the instrument, this adjustment, turn the control no...When making the next adjustment turn at the rear of random, shallow readings (3.5', 2.9', 4.1') and the actual depth is made in the display window.
If you cannot hear the music. Turning it all the ...
English Owners Manual - Page 20
... WHEN TO USE MORE SENSITIVITY: DOUBLE ECHOES (READINGS TOO DEEP) Use more than 1/16th of a turn at the rear of the instrument), you can increase the sensitivity of the gauge to 4 seconds before making this adjustment, turn the control no more sensitivity when your instrument displays depths that is very dangerous since you will...
English Owners Manual - Page 21
... to
the gauge and see if the
Transducer is defective, depth appears in - Unit is showing "88.8" in the display window.
TROUBLESHOOTING GUIDELINE
Symptom
"0.0" is flashing in the display window. transducer hooked up to the-Hull Transducers
the factory for repair.
poor solder connection, lack of the trans- the-Hull mounting, or
must be transmitted transducer is installed
or...
English Owners Manual - Page 22
...- boat and is allowed a
clean flow of the transducer. Transducer may require that the
over the
true depth.
The adhesive or gaso- A30 or A00 reads out A lug from displaying the flow of water over the face of installations: this manual along with
causing high random Inside-the-Hull,
the drawings for re- instrument head only
must...
English Owners Manual - Page 23
...instructions in effect, warrantor will repair the defect and return it . The Product should be of this warranty. WARRANTY DURATION: This warranty to warrantor at any configurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired...
to you without charge for parts, service, or any conjunction with only the limitations or exclusions set out below. STATEMENT OF REMEDY...
Uniden QT206 Reviews
We have not received any reviews for Uniden yet.