Icom IC-9100 Support Question
Icom IC-9100 Support Question
Find answers below for this question about Icom IC-9100.Need a Icom IC-9100 manual? We have 1 online manual for this item!
Question posted by wohnfeld on December 12th, 2016
Ic-9100 Power On
Turned radio accidentally using the supply. Now it won't power back on.
Current Answers
Related Icom IC-9100 Manual Pages
Instruction Manual - Page 2
... if not installed and used in a particular
NOTE
If disregarded, inconvenience only. Personal injury, fire hazard or electric shock may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which the receiver is required for making the IC-9100 your IC-9100. FOREWORD
SUPPLIED ACCESSORIES
Thank you to operate...
Instruction Manual - Page 3
...damage the transceiver surfaces.
BE CAREFUL! Turn OFF the transceiver's power and/or disconnect the DC power cable when you use a linear amplifier, set
the transceiver's RF output power to less than 16 V
DC to...metal, wire or other countries. NEVER put the transceiver in a secure place to the IC-9100 may be damaged. The transceiver warranty does not cover any problems caused by Icom Inc...
Instruction Manual - Page 4
... other repeaters using an Icom radio to other hams, for a reply.
Calls could be used :
• MY : T his is required for the DSTAR operation with other Area repeaters within them, and eventually to contact. Call sign routing, one you wish to the entire world.
CQCQCQ can operate simplex D-STAR with the IC-9100.
• D-STAR...
Instruction Manual - Page 32
...gasket 15 mm
Slide the nut, rubber
gasket and clamp
over the clamp.
The IC-9100 has an SWR meter to match the transceiver and antenna. PL-259 CONNECTOR INSTALLATION EXAMPLE..., along with output power and receiver sensitivity.
2 INSTALLATION AND CONNECTIONS
■ Antenna connection
For radio communications, the antenna is of the cable evenly. When using a lightning arrestor.
...
Instruction Manual - Page 38
... or optional AH-2b
Ground
[TUNER] Control cable
Ground
29 Nonmatched ALC and RF power settings could overheat or damage the linear amplifier.
• T he ALC input level...output power and linear amplifier ALC output level after referring to the linear amplifier instruction manual.
• T he IC-9100 SEND terminal (ACC connector pin 3) is exceeded, a larger external relay must be used.
...
Instruction Manual - Page 49
...IC-9100 displays carrier
4
frequency. any 5 MHz band frequency other than the five fre- Therefore, tune the transceiver to set all controls so that trans-
5.36650 MHz
5.36800 MHz
mission in this band meets the stringent conditions
5.37150 MHz
5.37300 MHz
under which amateur operations may use... ERP (Effective Radiated Power) • 2.8 kHz bandwidth
IC-9100 Displayed Frequency* 5.33050...
Instruction Manual - Page 54
... level when the
45
speech compressor is in use.
[AF] 46##BOE
Mode switches
[SPEECH/...allowable level, the ALC limits the RF power.
RF output power is always displayed.
➥ Hold ...turned OFF. (p. 164)
NOTE: If "SPEECH/LOCK" is not selected in the "[SPEECH/LOCK] SW" item of the antenna at the fre- Increases
[AF] ."*/#BOE
Decreases
■ Voice synthesizer operation
The IC-9100...
Instruction Manual - Page 79
..., in the normal way. • If you wish to communicate with each step equal to the frequency you were using before rotating [MAIN ... scope is a lot of signal noise, turn OFF the Preamplifier
to reduce the signal input level, and turn ON the Attenuator to select a frequency.
..., repeat steps e and r.
The IC-9100's Band Scope function can be used in the band scope indicator equal to...
Instruction Manual - Page 93
... MHz frequency band*. * The optional UX-9100 is in antenna tuner matches the transmitter to turn OFF the antenna tuner.
e S et...be measured on the microphone to select the RTTY mode. The IC-9100 can measure SWR two ways-
D Spot measurement
q P ush [TUNER] once or twice...10k
Start measuring Select number of output power (30%).
t R otate [RF POWER] clockwise past the 12 o'clock ...
Instruction Manual - Page 103
... the output power, if desired. (p. 46) t P ush [MENU] to the call.
tion is in use, this selec- To reply to turn ON the One-touch repeater function. • "T" and "DUP-" appear. • T he repeater receive (uplink) frequency appears at the
bottom of the function display. ■ Receiving a D-STAR repeater
When the IC-9100 receives a signal...
Instruction Manual - Page 162
... the output power too high. In the wrong mode, you cannot use the satellite, even if you use a reverse tracking satellite in the
SSB mode, use LSB for the uplink frequency and USB for the downlink frequency. • W hen using a normal tracking satellite in SSB mode,
use USB for the UX-9100), can be used with the IC-9100, and...
Instruction Manual - Page 169
...use with each frequency. NEVER operate the AH-4 when it is to the transceiver directly,
and not via the AH-4 antenna tuner. This function is turned ON in the Set mode. (p. 163).
■ Optional external tuner operation
• AH-4 HF/50 MHz AUTOMATIC ANTENNA TUNER The optional AH-4 matches the IC-9100...proper tuning may not start if the TX power output is com- ble longer than the ...
Instruction Manual - Page 183
...from the right side panel of the top/bottom cover, push them , or cause you turn the transceiver upside down . Carrying handle
Top cover
PA shielding plate
Bottom cover
Bottom cover...the transceiver's Warranty can be responsible for removing the covers of the IC-9100. R WARNING! Turn OFF the power and disconnect the DC power cable from the transceiver. Otherwise, there is sticky, so push it...
Instruction Manual - Page 184
...
y A ttach the UX-9100 and IF unit using the eight supplied screws. • Make sure the flat cable is not pinched when the UX9100 is turned OFF. NEVER push on the rear panel using your finger to use the transceiver for a long period of time, disconnect the transceiver's DC power cable. e C onnect the DC power cable, coaxial cables...
Instruction Manual - Page 188
...." !0 R otate [MAIN DIAL] to turn ON the calibration marker. • A sidetone may be performed by receiving radio station WWV, WWVH, or other standard frequency signals. Slide the tension adjustment to select the USB mode. CAUTION: The IC-9100 has been thoroughly adjusted and tested at 15...A very accurate frequency counter is required to calibrate the frequency of [MAIN DIAL] may be used.
Instruction Manual - Page 189
... of the problem, and repair it . Turn OFF the power and disconnect the DC power cable from the
DC power cable is located in the diagram
to the...fuse replacement
8
Except for transceiver protection. • DC power cable fuses ATC 30 A • Circuitry fuse ATC 5 A
R WARNING! The IC-9100 has two fuse types installed for the power amplifier, the 13.8 V DC from the transceiver before...
Instruction Manual - Page 191
... and sub transceivers. • T he master transceiver is used to send data to turn ON the power and enter the cloning mode. MAINTENANCE 17
■ Data cloning
DCloning between transceivers
The IC-9100 has transceiver-to clone/edit contents with a PC using a personal computer
The optional CS-9100 cloning software is also available to -transceiver data cloning...
Instruction Manual - Page 208
...low cut switch and mic gain control. The amplifier/power supply unit and the remote control unit can connect to tune a long wire antenna for base station operation. UX-9100 1200 mhz band unit
FL-430 1 st if ...external speaker
4 audio filters; Includes a low cut switch and mic gain control.
20 OPTIONS
IC-PW1/EURO HF/50 MHz ALL BAND 1 kW LINEAR AMPLIFIER
AH-4 hf automatic antenna tuner...
Instruction Manual - Page 209
...)
• RS-BA1 ip remote control software To remotely control radios using a personal computer equipped with an RS-232C port. Approved Icom ...that attached with the transceiver.
• UT-121 digital unit Allows the DV mode operation with the IC-9100.
• CS-9100 cloning software Use this software to 7-pin + 8-pin ACC connector.
• MB-123 carrying handle Convenient when carrying ...
Instruction Manual - Page 210
...require that this radio, to licensing conditions in the country of use. Further information can be beneath the antenna array and have the correct version of this radio or the correct... Some radio licenses will require some modes of transmission, SSB, CW, AM etc.
Versions of the IC-9100 which can create local, high intensity magnetic fields. have a lower 'average' output power and...
Similar Questions
How Can I Open The Ic 7200 For Transmission On Marine Channels?
I have been adviced that it is possible to modify so that I for safety reasons only, can trx on mari...
I have been adviced that it is possible to modify so that I for safety reasons only, can trx on mari...
(Posted by Runeedamm 5 months ago)
How Do I Change The Itu Region On This Radio? I Cannot Transmit In The 432 Range
Was testing a digital packet modem with the 9100 and realized I cannot transmit in the 432 Mhz area....
Was testing a digital packet modem with the 9100 and realized I cannot transmit in the 432 Mhz area....
(Posted by n1gmv 9 months ago)
How To Fix An Ic-2300h With Power Output Drops After 3 Seconds Of Transmit.
After adjusting power output using cable jig this problem occured and I can't revert to the previous...
After adjusting power output using cable jig this problem occured and I can't revert to the previous...
(Posted by hpberioso 1 year ago)
Over-current Shut Down On 2m And 432mhz.
My IC-9100 is only 8 months old and has not seen a lot of use. Yesterday I was on 2M FM when the pow...
My IC-9100 is only 8 months old and has not seen a lot of use. Yesterday I was on 2M FM when the pow...
(Posted by kentteri 7 years ago)