Ridgid R865N Support Question
Ridgid R865N Support Question
Find answers below for this question about Ridgid R865N.Need a Ridgid R865N manual? We have 2 online manuals for this item!
Question posted by jcmor1202 on April 4th, 2013
Warranty For Ridgid R865n
my circular saw only works sometimes when pulling the trigger. the battery is at full charge. how long is the warranty on this product and where can i take it?
Current Answers
Related Ridgid R865N Manual Pages
Operation Manual - Page 3
...work area clean and well lit.
Use of a GFCI reduces the risk of starting . Contain long hair. POWER TOOL USE AND CARE
Do not force the power tool. Use the correct power tool for carrying, pulling or unplugging the power tool...18 V nickel-cadmium and 18 V lithium-ion battery packs, see tool/appliance/battery pack/charger correlation supplement 988000-302. Failure to ...
Operation Manual - Page 4
...saw , they cannot be avoided by the operator, if proper precautions are taken.
4 - Blades that can dig into account the working conditions and the work properly to minimize body exposure, blade binding, or loss of the power tool is important to support the work to another battery... the operator. Position your saw to a stable platform. CIRCULAR SAW SAFETY WARNINGS
DANGER:
Keep ...
Operation Manual - Page 5
...work or pull the saw backward while the blade is in the material until the blade comes to them frequently and use . Wear hearing protection during extended periods of serious personal injury.
Battery tools...and kickback.
Blade depth and bevel adjusting locking levers must be charged in objects being thrown into the material. If blade adjustment shifts while cutting, it...
Operation Manual - Page 6
... trash. Please study them and learn their meaning. This product uses nickel-c admium (Ni-Cd) and lithium-ion (Li-ion) batteries. Local, state or federal laws may prohibit disposal of ...situation, which , if not avoided, may result in death or serious injury. Proper interpretation of batteries in death or serious injury.
Voltage
Current
Frequency (cycles per second)
Time
Type or a ...
Operation Manual - Page 7
.... (RPM) Motor 18 Volt DC
KNOW YOUR CIRCULAR SAW
See Figure 1, page 15. Before use of this product requires an understanding of work in .
NOTE: There are detentes in .
to secure the blade when turning the blade screw. LED LIGHT
The LED light, located on the tool and in . LOCK-OFF BUTTON
The lock-off...
Operation Manual - Page 8
...use this product until you unpack it. blade is misuse and could cause serious personal injury, always remove the battery pack from the tool when assembling parts. Use of the saw .
...personal injury. Circular Saw Blade 5 mm Blade Wrench Operator's Manual
WARNING:
If any parts on spindle.
ATTACHING THE BLADE
See Figure 2, page 15. Remove the battery pack from ...
Operation Manual - Page 9
... product will result in serious injury. Align raised rib on battery
pack with the groove inside the saw. Make sure the latches on blades will begin charging when placed on the underside of work.
Use gum and pitch remover, hot water, or kerosene to remove these built-in features may cause the battery and the tool...
Operation Manual - Page 10
...kickback and cause the cut to the closed , remove the battery from the workpiece while the blade is located on the saw can be repositioned for knots or nails before cutting. Kickback... full speed before beginning a
cut. Hold the saw and to "kickback" towards you pull the switch trigger. WARNING:
When using the saw from the saw. LOCK-OFF BUTTON
See Figure 10, page 16. The ...
Operation Manual - Page 11
...saw . The angle of cut release the trigger and allow the blade to come to be set at full depth of workpiece. Depress the lock-off " piece. Place the workpiece with the saw. Remove the battery... 18 - 20, page 17. OPERATING THE SAW
See Figures 13 - 14, page 17. CROSS CUTTING/RIP CUTTING
See Figures 15 - 16, page 17. When making long or wide rip cuts with the "good" side...
Operation Manual - Page 12
....
To adjust positive 0° bevel stop : Remove the battery pack from the saw. Rotate the bevel adjustment lever counterclockwise to
release. Turn TORX® T-8 adjustment screw with the blade will cause serious injury.
Depress the lock-off button and squeeze the switch trigger to climb up using a combination square.
Operation Manual - Page 13
... solvents and may result.
WARNING:
Do not at a RIDGID® authorized service center.
BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING
WARNING:
To avoid serious personal injury, always remove the battery pack from the tool when cleaning or performing any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in serious personal injury...
Operation Manual - Page 14
... even cordless batteries in to you must return it; ADDITIONAL LIMITATIONS
To the extent permitted by One World Technologies, Inc.
WARRANTY
RIDGID® HAND HELD AND STATIONARY POWER TOOL 3 YEAR LIMITED SERVICE WARRANTY
Proof of purchase must present proof of purchase and return all original equipment packaged with the original product.
To receive a replacement tool you may...
Similar Questions
Finish Nailer R250af18 Not Firing.
How are you? I need help because my Finish Nailer R250AF18 not firing. When I press it to the wood i...
How are you? I need help because my Finish Nailer R250AF18 not firing. When I press it to the wood i...
(Posted by famnb18 2 years ago)
Rp-210 Crimper Tool
how can we order a replacement motor for the tool. the end has come off part way and the tool in una...
how can we order a replacement motor for the tool. the end has come off part way and the tool in una...
(Posted by webb97907 8 years ago)
Does Anyone Have A Wiring Diagram For A Ridgid 4510 Table Saw
Hi. A few monthe ago I took my motor out of my Ridgid 4510 saw to have it repaired. Disassembly was ...
Hi. A few monthe ago I took my motor out of my Ridgid 4510 saw to have it repaired. Disassembly was ...
(Posted by joboptional09 8 years ago)
Saw Blade Stops On Cut
why does mitter saw blade stop in the middle of the cut
why does mitter saw blade stop in the middle of the cut
(Posted by amazingwoodflooring 8 years ago)
