Troy-Bilt CS 4265 Support Question
Troy-Bilt CS 4265 Support Question
Find answers below for this question about Troy-Bilt CS 4265.Need a Troy-Bilt CS 4265 manual? We have 2 online manuals for this item!
Question posted by highleyleroy on January 8th, 2022
Fill Cap
What is for the fill cap above the oil fill cap for?
Current Answers
Related Troy-Bilt CS 4265 Manual Pages
Operation Manual - Page 4
...refuel it becomes necessary to the machine.
4.
e.
f. Never fuel machine indoors. g.
h. Replace gasoline cap and tighten securely.
j. If gasoline is complete. k. To reduce fire hazards, keep the machine in this... deflectors and safety devices in the discharge area. Never attempt to build up oil or fuel spillage and remove any damaged parts. Shut the engine off . ...
Operation Manual - Page 5
... or death, do not modify engine in any ). Important Safe Operation Practices
5 Spark Arrestor
6. apply on off-season storage.
10.
EPA emission regulations for gas, oil, Resources Code).
Always refer to operate at least 5 minutes before storing.
9. to the Consumer Products Safety Commission (CPSC) and the U.S. Environmental Protection Agency (EPA), this...
Operation Manual - Page 7
... the raised position. See Fig. 3-2.
Assembly & Set-Up
3
Contents of Carton
• One Chipper Shredder • One Tow Bar • One Bottle of Oil
• One Operator's Manual • One Bag
• One Engine Operator's Manual • One Safety Glasses
Assembly
NOTE: This unit is tight around chute
deflector ...
Operation Manual - Page 8
...the box.
See Fig. 3-4.
3
2 3
Figure 3-4
8
Section 3 - Add oil provided before starting unit for additional engine information.
1. Gasoline is hot or running . See Fig. 3-3.
1
Set-Up
...base. Service the engine with the spring pin to cool for information regarding adding and checking the oil.
2. Figure 3-3
2. Assembly & Set-Up Fasten with gasoline as instructed in the separate engine...
Operation Manual - Page 10
... on the spark plug.
2. Let rope rewind slowly.
7. Operation
5
WARNING: The operation of any chipper shredder can damage your particular unit. Make certain the metal cap on the end of any kind.
6. Always wear the safety glasses provided with a rapid, continuous, full arm stroke. These factors depend on what make sure...
Operation Manual - Page 12
... it could contaminate the fuel system. Read and follow instructions carefully.
• Check engine oil level before , cleaning, lubricating, or performing any maintenance.
• The warranty on this... Clean the chipper shredder thoroughly after each use .
• Wash bag periodically with light oil once a season.
3.
Lubricate the pivot points on the chute deflector with water.
Remove all...
Operation Manual - Page 14
... Chamber.
3. Follow the original angle of
the impeller. Remove the two flange nuts (and hex bolts) which secure it to the impeller housing.
C
B
A
Model Series CS 3210 Shown
Figure 7-1
4. Service
7
Blade Care
Chipper Blades
WARNING: The impeller's chipper blades are reassembled with the hardware removed earlier or sharpen. See Fig. 7-1A...
Operation Manual - Page 15
... a component that can create a spark. Insert a piece of the shredder blade.
lock washers which secure hopper inlet guide to completely free shredder blade. Using a light oil or silicone, coat the equipment, especially any springs, bearings, and cables. Service
15 Carefully separate the hopper assembly from the heavy side until it aside...
Operation Manual - Page 16
...disconnect spark plug wire. Always run engine at full throttle. 4. Engine oil level low. 2. Carburetor idle mixture adjustment
improperly set. 1.
Clean, adjust gap, or replace. 8. Clean fuel... line; Refill with proper oil. 2. Refer to spark plug. 4. Clean flail screen and inside of discharged material ...
Operation Manual - Page 21
... from the sale. Troy-Bilt shall not be liable for incidental or consequential loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services or for a period of purchase.
IMPORTANT: Owner must present Original Proof of the exterior finish due to use the product. Phone 1-800-668...
Service Manual - Page 6
...muffler.
4.3. Remove all moving parts have come to a complete stop.
4.2. Remove the four hex cap screws securing the tube support to between 20 ft-lbs and 25 ft-lbs.
4. Disconnect the ...spark plug wire and keep it is balanced evenly. Perimeter Hex Cap Screws
Figure 11
4 WARNING: The muffler and surrounding area will need a special removal tool, ...
Service Manual - Page 8
...
IMPORTANT: The roll pin should be inspected and replaced by removing the roll pin retainer clip, roll pin and clevis pin. Perimeter Hex Cap Screws
Figure 16
6 Remove the four hex cap screws securing the tube support to the inner housing. See Figure 15.
5.6. Flail
Roll Pin Retainer Clip
Tube Support
Hex...
Similar Questions
The Gas Cap Won't Come Off
i I can't get the gas cap off and the tank is lose
i I can't get the gas cap off and the tank is lose
(Posted by Cynthiaschimpf 2 years ago)
Troy Bilt Cs 4265
Could not start engine, replaced spark plug, started for 1 minute only after spread starter, and sto...
Could not start engine, replaced spark plug, started for 1 minute only after spread starter, and sto...
(Posted by fangchlee 7 years ago)
Troy Bilt Tb575 Fuel Leak From Cap And From Carb Area, Used Only A Few Times.
(Posted by edonscene 9 years ago)
Troy Cs 4325 Oil Change Procedure
How do I change the oil in my chipper shredder
How do I change the oil in my chipper shredder
(Posted by gbaker1951 9 years ago)