JET Tools 1-Phase Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools 1-Phase manuals!
Problems with JET Tools 1-Phase?
Ask a Question
Free JET Tools 1-Phase manuals!
Problems with JET Tools 1-Phase?
Ask a Question
JET Tools 1-Phase Videos
Powermatic 1791304 DT45 4 Line Single End 1 Horsepower Dovetailer 115230 Volt 1 Phase
Duration: 1:11
Total Views: 108
Duration: 1:11
Total Views: 108
Popular JET Tools 1-Phase Manual Pages
User Manual - Page 1
This .pdf document is bookmarked
Operating Instructions and Parts Manual
Manual Cold Saws
Models CS-275, CS-315
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
model CS-315 shown
Part No. M-414226 Revision C1 04/2014 Copyright © 2014 JET
User Manual - Page 2
... purposes default to become inoperable within a
reasonable amount of delivery. Manual Hoists; Shop Tools; If one year from the date of use the Service Center Locator on official JET website are given as expendable parts or accessories expected to a Two Year Warranty. Consumable items;
JET® branded products are not binding.
SOME STATES DO NOT ALLOW...
User Manual - Page 3
......9 8.4 Coolant tank ...9 8.5 Splash plates...9 8.6 Length stop...10 9.0 Electrical connections ...10 9.1 Three-phase models ...10 9.2 Single-phase models...10 9.3 Voltage conversion (model CS-275-1 only 10 9.4 Grounding instructions ...11 10.0 Adjustments ...11 10.1 Miter adjustment...11 10.2 Vise ...11 10.3 Stops ...11 10.4 Blade replacement ...12 11.0 Controls ...12 12.0 Operation ...12 13...
User Manual - Page 4
... other moving parts. Keep children away.
21.
The right tool will operate properly and perform its intended use extreme caution and replace the guards immediately after maintenance is properly grounded.
13. Do not operate this manual. If you do the job better and more safely.
4 Read and understand the entire owner's manual before connecting the machine...
User Manual - Page 5
...that if precautions are not heeded, it
5 Retain this document. Maintain tools with the instructions as shown in the specifications section of the cold saw as set forth in this manual.
26. Do not stand on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. Turn the power off the machine and disconnect from the area before...
User Manual - Page 6
... the lever is moved to the right and is released when the lever is set by means of a blade support unit with indicator light, a mushroom style red emergency OFF switch, coolant flow ... panel features independent ON and OFF buttons with guard, transmission unit, and motor. Coolant is pivoted downward manually by adjusting the depth stop assembly for speed selection. 5.0 Cold saw blade...
User Manual - Page 7
...specifications in this manual were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations.
7 TEFC, 1-1/2HP, 1PH, 115/230VAC, 60Hz
(prewired 115V) Plug...96.5cm) Saw motor TEFC, 1-1/2HP, 3PH, 230VAC, 60Hz .... 6.0 Specifications
Model numbers CS-275 CS...
User Manual - Page 10
... directly to a service panel. Figure 7
9.3 Voltage conversion (model CS275-1 only)
To convert from 115V to Figure 7.
1. On all relevant codes. Re-tighten the top knob to secure the zero setting.
9.1 Three-phase models
The CS-275 (3-phase) and CS-315 (3-phase) are not supplied with a plug. See section 9.3. You may be connected. During hard-wiring of the 3phase wires on while the...
User Manual - Page 11
... (A diagram is set, move the vise jaw about 1/16-inch away from power source. 2. If repair or replacement of electric shock.
...connect the equipmentgrounding conductor to the left . Use a 10mm hex key to reduce the risk of the electric cord or plug...service personnel if the grounding instructions are provided for 230V operation.
9.4 Grounding instructions
This machine must be grounded.
User Manual - Page 12
...blade guard at the handwheel to secure the setting of the blade, then retighten screw.
3.... active to Low or High (3-phase models only), and the trigger on the...power. 2. NOTE: A long work piece and close the vise; 10.4 Blade replacement
Disconnect machine from the power source before changing saw blade (Figure 12): 1. Emergency Stop - The green ON button must have proper support...
User Manual - Page 13
...sight glass with the power switched OFF. Some recommended brands are available at your local industrial distributor. The plug also serves as sheet... plug on the coolant pump.
13.4 Lubrication
For long life and trouble free operation, it is essential that replaced parts and/or any tools ...the limitations and specific applications of the different types of the downstroke.
8. Pivot joints ...
User Manual - Page 16
... pressure.
15.0 Troubleshooting
15.1 Blade and cutting problems
Problem
Teeth breaking
Rapid tooth wear Broken blade Cuts not straight
Probable Cause
Coolant flow problem
Material too hard
...correct concentration.
Check and use a lower blade speed and reduced feed pressure.
Contact JET technical support. Table 5
16
These zones, which are using.
After the wearing-in the cut...
User Manual - Page 17
Check: the phases; Also check that socket/plug connection from handle to protect the motor, check the amperage setting, re-set, and check the motor.
Make sure it are present both on the following pages. The winding can be rewound or replaced by experienced motor repair personnel. Otherwise replace. To order parts or reach our service department, call will not turn
Magnetic ...
User Manual - Page 20
...-67 Coupling...1 68 CS275-68 Motor 1.5HP, 220V, 3PH......... 1 CS275-68-1 Motor 1.5HP, 115/230V, 1PH.. 1 69 CS275-69 Wire Terminal Clamp 4 70 CS275-70 Control Wire 1 71 TS-1490031 Hex Cap Screw M8x20 4 72 TS-0680031 Flat Washer 5/16 4 73 CS275-73 Oil Plug 1/2" PT 1 74 TS-0271031 Socket Set Screw 3/8"-16x3/8 2 75 CS275-75...
User Manual - Page 24
... CS275-67 Coupling...1 68 CS315-68 Motor 2HP, 220V, 3Ph 1 CS315-68-1 Motor 2HP, 220V, 1Ph 1 69 CS275-69 Wire Terminal Clamp 4 70 CS275-70 Control Wire 1 71 TS-1490031 Hex Cap Screw M8x20 4 72 TS-0680031 Flat Washer 5/16 4 73 CS275-73 Oil Plug 1/2" PT 1 74 TS-0271031 Socket Set Screw 3/8"-16x3/8 2 75 CS315-75...
JET Tools 1-Phase Reviews
We have not received any reviews for JET Tools yet.