Cisco WS-CBS3020-HPQ Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco WS-CBS3020-HPQ manuals!
Problems with Cisco WS-CBS3020-HPQ?
Ask a Question
Free Cisco WS-CBS3020-HPQ manuals!
Problems with Cisco WS-CBS3020-HPQ?
Ask a Question
Most Recent Cisco WS-CBS3020-HPQ Questions
Please Can You Tell Me How To Reset Cisco Ws Cbs 3020 Switch To Factory Default?
(Posted by dejandamjanovic3 9 years ago)
Popular Cisco WS-CBS3020-HPQ Manual Pages
Installation Guide - Page 23
...3000 Switch Rear Panel
Power Converter (Optional)
201697
1 DIN rail latch
2 Foot in recessed position
Power Converter (Optional)
The switch can get a replacement power cable (PWR-IE3000-CLP=) by calling Cisco Technical Support. The power converter (PWR-IE3000-AC) can supply 24-VDC power to one switch and up to two modules. OL-13017-01
Cisco IE 3000 Switch Hardware Installation Guide
1-13...
Installation Guide - Page 43
...power source wire extends from the power and relay connector.
Figure 2-13
Stripping the Power Connection Wire 1
97489
1 0.25 in. (6.3 mm) ± 0.02 in. (0.5 mm)
Step 5
Insert the exposed part... extend from the power and relay connector after installation. Statement 122
OL-13017-01
Cisco IE 3000 Switch Hardware Installation Guide
2-17 Figure 2-12
Power and Relay Connector
...
Installation Guide - Page 46
...5 Power source B return connection 6 Power source B -48 VDC connection 7 External device 2, relay wire connection 8 External device 2, relay wire connection
Step 8
(Optional) If you plan to connect external alarm devices to the alarm relays and the switch is already installed, go to the "Wiring the External Alarms" section on page 2-11.
2-20
Cisco IE 3000 Switch Hardware Installation Guide...
Installation Guide - Page 47
... that they cannot be disturbed by casual contact. OL-13017-01
Cisco IE 3000 Switch Hardware Installation Guide
2-21
Chapter 2 Switch Installation
Verifying Switch Operation
Attach the Power and Relay Connector to the Switch
Follow these steps to attach the power and relay connectors to the front panel of the power and relay connector.
For example, use tie wraps to secure...
Installation Guide - Page 48
... red, and then go off power to install the switch.
2-22
Cisco IE 3000 Switch Hardware Installation Guide
OL-13017-01 Note For instructions on page 2-53. To test the switch, follow these steps: • Power On the Switch, page 2-22 • Verify POST Results, page 2-22 • Disconnect Power, page 2-22
Power On the Switch
To apply power to a switch that services the DC circuit, and...
Installation Guide - Page 60
Connecting Power and Alarm Circuits
Chapter 2 Switch Installation
Figure 2-29
Torquing the Power and Relay Connector Captive Screws
202030
V RT A A
Step 5 Repeat Step 1 through Step 4 to insert the input and output wires of an additional external alarm device into the second power and relay connector.
2-34
Cisco IE 3000 Switch Hardware Installation Guide
OL-13017-01
Installation Guide - Page 63
... to an RJ-45 connector on the front of the switch. See Chapter 3, "Troubleshooting," for the list of the same type as the SFP module on when both the switch and the connected device have established link.
Installing and Removing SFP Modules
These sections describe how to cabling problems.
Reconfigure and reboot the connected device if necessary. See...
Installation Guide - Page 73
...48
Preparing the AC Power Cord
To connect the power converter to 2 in-lb. Power cord connector types vary by country. OL-13017-01
Cisco IE 3000 Switch Hardware Installation Guide
2-47 Power-cord color codes also vary by country. Figure 2-41 1
Connecting Wires to the Power Converter DC Output Terminal Block
2
3
5
1 6
2
7
1
3
8
2 4
CONSOLE
202298
1 DC power clip
3 Four-pin connector...
Installation Guide - Page 75
... the connector.
See Figure 2-44. See Figure 2-43. Ensure that only
wire with insulation extends from the input power terminals and set it aside. OL-13017-01
Cisco IE 3000 Switch Hardware Installation Guide
2-49
Figure 2-43
AC/DC Power Input Terminal Block
202299
1
1 Ground wire Step 2 Insert the exposed ground wire lead into the AC outlet...
Installation Guide - Page 79
... connected, the switch automatically begins the power-on the power converter front panel is green when the unit is satisfactory, the switch does not need further configuration. For instructions on Cisco.com for the AC outlet or the DC control circuit to Go Next
If the default configuration is operating normally. OL-13017-01
Cisco IE 3000 Switch Hardware Installation Guide
2-53 The...
Installation Guide - Page 81
... Switch Hardware Installation Guide
3-1 They show power-on , it begins the POST, a series of tests that runs automatically to complete POST. Verify Switch POST Results
As the switch powers on self-test (POST) failures, port-connectivity problems, and overall switch performance. Note POST failures are usually fatal.
It might need to reset the terminal-emulation software to the console...
Installation Guide - Page 127
... the Power Converter" section on page B-16. Ltd. OL-13017-01
Cisco IE 3000 Switch Hardware Installation Guide
B-37 Designation of plastic material: type E4009 Generic name of plastic material: liquid-crystal polymer Relay body: manufacture of plastic material, Sumitomo Chemical Co. Relay cover: manufacturer of plastic material, Sumitomo Chemical Co. Following is found, replace the...
Installation Guide - Page 129
OL-13017-01
Cisco IE 3000 Switch Hardware Installation Guide
B-39 See Figure B-29 for details. The torque should not exceed 2 in -lb. Appendix B Installation In a Hazardous Environment
Connecting Power and Alarm Circuits
Step 4 Use a ratcheting torque flathead screwdriver to torque the power and relay connector captive screw (above the installed wire leads) to insert the input and output...
Installation Guide - Page 132
... the stipulated cable length for the list of the switch. If the port LED does not turn on:
• The device at the other end might be turned on the front of supported modules. See Chapter 3, "Troubleshooting," for loops. This can use any combination of rugged SFP modules.
Installing and Removing SFP Modules
These sections describe how...
Installation Guide - Page 167
... 1-11 port status 1-10 POST results 3-1 power status 1-9 setup 1-8 system 1-9 troubleshooting with 3-2
lightning activity warning 2-2, B-2 link status troubleshooting 3-3
M
management options 1-14 to 1-15 module
configurations 2-6, B-9 connecting 2-8, B-11 mounting rack 2-29 to 2-31, B-33 to B-35 MT-RJ connector C-3 See also 100BASE-FX ports
Cisco IE 3000 Switch Hardware Installation Guide
IN-3
Cisco WS-CBS3020-HPQ Reviews
We have not received any reviews for Cisco yet.