JET Tools VBS-2012 Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools VBS-2012 manuals!
Problems with JET Tools VBS-2012?
Ask a Question
Free JET Tools VBS-2012 manuals!
Problems with JET Tools VBS-2012?
Ask a Question
Popular JET Tools VBS-2012 Manual Pages
User Manual - Page 1
M-414482 Revision G2 03/2014 Copyright © 2014 JET This .pdf document is bookmarked
Operating Instructions and Parts Manual
20-inch Metalworking Band Saw
Model VBS-2012
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No.
User Manual - Page 2
... JET website. The specifications listed in Canada by a 90 day limited warranty against manufacturers' defects. Machine Accessories; JET Parallel clamps; Manual Hoists;
Who is Covered This warranty covers any additional action needed. If a product requires further inspection, the Technical Service representative will be asked to provide proof of our tools needs service or repair...
User Manual - Page 3
Parts List...24 19.0 Electrical Connections...29
3 Exploded View 22 18.1.2 VBS-2012 Band Saw (Welder Assembly) - Exploded View 23 18.1.3 VBS-2012 Band Saw - 2.0 Table of contents
Section
Page
1.0 Warranty and Service...2 2.0 Table of contents...3 3.0 Safety warnings...4 4.0 About this manual ...5 5.0 Specifications ...6 6.0 Uncrating and assembly ...7 7.0 Installation ...7 8.0 ...
User Manual - Page 4
... at the correct speed and feed rate. The right tool will operate properly and perform its operation. Make certain the machine is damaged should be properly repaired or replaced.
17. Keep the floor around , carrying on .
15. Read and understand the entire owner's manual before connecting the machine to filter out microscopic particles.
10...
User Manual - Page 5
... machine before any blade replacement, drive belt replacement, or any periodic service or maintenance is provided by JET covering the safe operation and maintenance procedures for a JET Model VBS-2012 Band Saw. The saw is not running unattended. Don't use push sticks when cutting small material.
32. Keep work pieces from the blade. Retain this manual:
This means that...
User Manual - Page 6
...15°R and 12°L Blade length (approximate 150-1/2" min.; 156-1/2" max. 5.0 Specifications
Model number ...VBS-2012 Stock number ...414482 Blade speed ...variable
Low range ...65-555 High range...390-3280 ...1310 lb
The specifications in this manual were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any ...
User Manual - Page 7
...observe in the motor junction box (see section 19.0, Electrical Connections).
7 Figure 1
7.0 Installation
1. The VBS-2012 Band Saw is a disconnect near the machine for 230 volt operation, or "hard-wire"...directions.
5. Remove two socket head cap screws from power source. All adjustments or repairs must be done with locking knob. Use the lifting ring to 460V conversion.
8.2 ...
User Manual - Page 16
...Set guide post closer to the job.
16 Use slower speed. Fix guide post in position. Increase tension. 15.0 Troubleshooting
15.1 Operating problems
Table 1
Trouble
Probable Cause Blade has been improperly welded. Blade not installed.... File to proper set . Replace pulley.
Decrease feed rate. Contact technical service for short radius cutting. Sharpen or replace blade. Saw blade ...
User Manual - Page 17
... Replace with adequate size and length cord.
One cause of correct size. If too heavy a cut .
Extension cord too light or too long. If problem persists, check amp setting ...If voltage between starter and motor is suspect, you have a motor problem. 15.2 Mechanical and electrical problems
Table 2
Trouble
Machine will not start/restart or repeatedly trips circuit breaker or blows ...
User Manual - Page 19
... switch connecting nut tighter. Rotate pressure selector knob accordingly. Jaws do not move. Grinder will not return to correct position after release. Replace lower jaw inserts.
15.4 Welder mechanical problems
Table 4
Trouble
Weld could not be tightly clamped with a file. connecting point of order. Annealing doesn't occur when annealing button is pushed. Grinder...
User Manual - Page 21
... website for business hours, www.jettools.com). Note: An asterisk in the parts list indicates the part belongs to serve you quickly and accurately. To order parts or reach our service department, call will allow us to a complete assembly.
21 17.0 Typical Band Saw Operations
Figure 20
18.0 Replacement Parts
Replacement parts are listed on the following pages.
User Manual - Page 23
Exploded View
23 18.1.2 VBS-2012 Band Saw (Welder Assembly) -
User Manual - Page 24
... Shaft 1 G6201 .......BB-6201V Ball Bearing 2 1350 ..........VBS2012-1350.......... Right (s/n prior to 0709140 1 VBS1220M-1031....... On 1 6602 ..........VBS2012-6602.......... Work Table ...1 1020 ..........VBS1220M-102......... Motor Suspension Arm 2
24 18.1.3 VBS-2012 Band Saw - Parts List
Index No Part No
Description
Size
Qty
Control Panel Assembly
6600...
User Manual - Page 26
...Air Pump Cover 1 4030 ..........VBS2012-4030.......... Air Pump Housing 1 4140 ..........VBS2012-4140.......... Air Outlet * ...1 4150 ..........VBS2012-4150.......... Air Nozzle Clip 1 BM38.........VB-M39 V-Belt *...1 VBS16-401CP........... Rear Door - Upper Door - Upper Door Hinge 2 9999 ..........VBS2012-9999.......... Eye Bolt ...1 STRIPE-1-3/4 JET Stripe (not shown 1-3/4 per...
User Manual - Page 27
...PR-EV-6220 Spring - Shield Joint 1 6830 ..........VBS2012-6830.......... Arm Housing Adjuster 1 6910 ..........VBS2012-6910.......... Brass Handwheel 1 VBS2012-6950CP..... PR-EV-6020 Guide Block 1 6021 ..........PR-EV-6021 Spring Bracket 1 6030 .......... PR-EV-6100 Clamp Support - Shaft Housing 1 VBS2012-7200CP..... Detector Housing 1 7330 ..........VBS1220M-661...
JET Tools VBS-2012 Reviews
We have not received any reviews for JET Tools yet.