Optoma EH415e Support and Manuals
Get Help and Manuals for this Optoma item
This item is in your list!
View All Support Options Below
Free Optoma EH415e manuals!
Problems with Optoma EH415e?
Ask a Question
Free Optoma EH415e manuals!
Problems with Optoma EH415e?
Ask a Question
Popular Optoma EH415e Manual Pages
Manual - Page 3
Table of contents
Setup | LAN Settings 42 Setup | Control Settings 43 Options...44 Options | Input Source 47 Options | Remote Settings 48 Options | Advanced 49 Options | Lamp Setting 51 LAN_RJ45...53
Appendices 63 Troubleshooting 63
Image...63 Other...64 Projector LED Status Indicator 65 Remote Control...66 Replacing the Lamp 67 Compatibility Modes 70 Video Compatibility 70 Video ...
Manual - Page 8
... box. Remote Control
2 x AAA Batteries
Carrying Case
Documentation :
User's Manual Warranty Card Basic User's Manual
7 If something is missing, please contact Optoma customer service. Projector with lens cap
Power Cord 1.8m 15 pin D-sub VGA Cable
Noottee
Due to ensure all parts listed below are in each Country, some regions may have different...
Manual - Page 14
... sources. Noottee
Due to the projector. Remove the lens cover.
2. Noottee
3. The projector's startup logo screen displays and ... "Source"
button sequentially to turn On the projector. If the connected device is enabled. Ensure the...projector. (Check the user manual of the
laptop to determine the appropriate Fn key combination to change
display output.)
See Security Settings on the projector...
Manual - Page 15
... the button again to restart the projector. 3. Warning Indicator
Noottee
▀■ When the Lamp LED indicator lights red, the projector will display the following message on again after it has cooled down. First push of the projector or " " on , you should contact your local reseller or service center. The projector reaches stand-by mode. Please...
Manual - Page 23
...)
H/V
3D Mode 3D->2D 3D Format 3D Sync Invert
Exit
DLP-Link/IR/Off 3D/L/R
Auto/SBS/Top and Bottom/Frame Sequential On/Off
Language
Projection
Bahasa Indonesia
Menu Location
Screen type
Security Projector ID Audio Settings
Advanced Network
Security Security Timer Change Password
Exit Internal Speaker
Mute Volume Audio Input
Exit
Logo Logo...
Manual - Page 34
... Controls
Setup
Language
Enter the Language menu. Select the multilingual OSD menu. Screen Type
Press ◄► to set the aspect ratio to 16:9 or 16:10. This function is only available for more information. Projection
Select projection method:
Front Desktop
The factory default setting.
Rear Desktop
When you select this function, the projector...
Manual - Page 40
... are turned on the internal speaker. Audio Input
Press ◄► to increase the volume. Volume
Press ◄ to decrease the volume. English
User Controls
Setup | Audio Settings
Internal Speaker Off-turn on . On-the speaker volume and audio out are turned off the internal speaker. On-turn off .
Manual - Page 43
Off: Assign an IP address manually.
IP Address-Select an IP address Subnet Mask-Select subnet mask number. Gateway-Select the default gateway of the network connected
to the projector.
DNS-Select DNS number. Apply-Press "ENTER" to the projector from the DHCP server automatically. User Controls
Setup | LAN Settings
Noottee
Network sub-menu can only...
Manual - Page 54
... be controlled by AMX ( Device Discovery ). http://www.crestron.com/ This projector is supported by a PC (Laptop) or other countries by the specified commands of Extron Electronics, Inc. Also, projector status information, such as remotely manage: Power On/Off, Brightness and Contrast settings. of
the United States.
AMX is a registered trademark of America, and...
Manual - Page 64
English
Appendices
Troubleshooting
If you have removed the lens cap and the projector is
switched on. Please
refer to the "Replacing the Lamp" section.
Make sure you experience a problem with your projector, please refer to the following :
Please setup the display format as 16:9 (wide) aspect ratio type
on your local reseller or service center. See pages...
Manual - Page 70
...6. Remove the two screws from the lamp module. While installing, align the lamp module with the connector and ensure it is replaced. Lamp Reset: (i)Press "Menu" -> (ii)Select "Options" -> (iii)Select "Lamp Settings" ->(iv)Select "Lamp Reset" -> (v)Select "Yes".
69 English
Appendices
4
Lamp Replacing Procedure: 1. Switch off the power to the projector by pressing the Power button. 2. Allow...
Manual - Page 82
... projector name set on
Inquiry about the manufacturer name
"Optoma" is returned. English
Appendices
Noottee
This projector is fully compliant to 5 digits):
state
Cumulative LAMP operating
time (This item shows a lamp
operating time (hour) calculated
based on that LAMP MODE is
LOW.)
2nd value: 0 = Lamp off, 1 =
Lamp on
projector name
the NETWORK menu or the
ProjectorView
Setup...
Data Sheet - Page 1
... ratio makes it ideal for large screen applications Lens shift for installation flexibility Full 3D compatibility for audience captivating immersive presentations 1.5x zoom ratio for greater installation placement flexibility
CONNECTIVITY (May require optional accessories)
The Optoma EH415e is the perfect projector solution for LAN command and control. Engineered for today's digital world...
Data Sheet - Page 2
...PROJECTOR - EH415e
OPTICAL/TECHNICAL SPECIFICATIONS
Display Technology Single 0.65" DC3 DMD DLP® Technology by Texas Instruments™
Native Resolution
Full HD (1920x1080)
Maximum Resolution
WUXGA (1920x1200)
Brightness (Typical)
4200 lumens
Contrast Ratio
15,000:1 (full on/full off)
Displayable Colors
1.07 Billion
Lamp...Lens
F=2.42-2.97, 1.5x manual zoom and focus
Lens Shift ...
Optoma EH415e Reviews
Do you have an experience with the Optoma EH415e that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Optoma yet.
Earn 750 points for your review!