Optoma W402 Support and Manuals
Popular Optoma W402 Manual Pages
Manual - Page 1
............ 48 SETUP | Network|Control Settings..... 50 SETUP | Advanced 51 OPTIONS 52 OPTIONS | Lamp Settings 55 OPTIONS | Remote Settings 57 OPTIONS | Advanced 58 OPTIONS | Optional Filter Settings.... 59
Appendices 60 Troubleshooting 60
Image Problems 60 Other Problems 62 Remote Control Problems 62 LED Lighting Messages 63 On Screen Messages 64 Replacing the Lamp 65 Installing and...
Manual - Page 3
...
Precautions
Please follow the procedures listed under "Replacing the Lamp" section on pages 65-66.
Do not look into the projector's lens when the lamp is in this user's guide. The bright light may cause electric shock.
Reset the "Lamp Reset" function from the onscreen display "Options|Lamp Settings" menu after replacing the lamp module (refer to cool down .
This...
Manual - Page 5
... / WXGA (1280x800) Native resolution
ing on the screen.
In order to minimize the lamp power, use room blinds to point out something on model. HD compatible - 720p and 1080p supported
...; Avoid staring/facing directly into the projector beam at all times. Keep your back to the beam as much as possible.
When projector is used in a classroom, adequately ...
Manual - Page 6
... contents to remove it before you turn on model, specification and region.
*2 For European warrant information please visit www. Standard Accessories
Projector
Power Cord
VGA Cable
*1 Optional accessories vary depending on the projector. For your safety, if the projector is missing, please contact Optoma customer service. Carry Bag
Lens Cap
HDMI Cable
English...
Manual - Page 24
..."4".
``Press to choose VGA source. ``Use as numberic keypad number "5".
``Press to setup.
``Use as numberic keypad number "6".
``User defined keys. Please see page 56 to... Control
3D / 3
``Press to the input source.
Press to automatically synchronize the projector to manually select a 3D mode that matches your 3D content.
``Use as numeric keypad number "0". English 24
HDMI / 4 VGA ...
Manual - Page 38
...if the image
time projector is auto-
Exit
Choose "Exit" to flicker vertically.
user tune
to manually and are saved
Frequency
in the settings after that for .... grayed out, and if "Signal" is only sup-Automatic
ported in settings after Change the display data frequency to manually
matic, the phase,
tune and saved in Analog
Automatically selects the singal...
Manual - Page 48
... To assign IP, Subnet Mask, Gateway and DNS configuration manually. DNS Display DNS number.
IP Address Display the IP address.
DHCP `` On: Projector will automatically apply the entered values. Subnet Mask Display subnet...).
Exit Choose "Exit" to the projector.
User Controls
SETUP | Network|LAN
Settings
Network Status Display the network connection status (read -only).
English 48
Manual - Page 59
... In- Choose this function to exit the menu.
59 English User Controls
OPTIONS | Optional Filter
Settings
Filter Usage Hours
Display the filter time.
"Filter Usage
Optional Filter Installed
Hours / Filter
`` Yes: Display warning message after replacing or cleaning the dust
filer.
Exit
Choose "Exit" to show or hide the warning message...
Manual - Page 60
..., go to the following information. Please refer to the "Replacing the Lamp" section. `` Make sure you experience a problem with your projector, please refer to the following : `` Please setup the display format as 16:9 (wide) aspect ratio
type on your local reseller or service center.
Appendices
English 60
Troubleshooting
If you have removed the lens cap and the...
Manual - Page 62
To replace the lamp, follow the procedures in the "Replacing the Lamp" section.
If this happens, the projector will burn out and may
make a loud popping sound. English 62 Appendices
Other Problems
T he projector stops responding to within ±15°
both horizontally and vertically of on of life, it will not turn off the projector, then unplug the...
Manual - Page 66
... not touch the glass area of the projector. 2. Use a dry cloth to shatter. Lift up the lamp handle 6 and remove the lamp module slowly and carefully. 7
To replace the lamp module, reverse the previous steps. 10. Lamp Reset: (i) Press "Menu" (ii) Select "OPTIONS" (iii) Select
"Lamp Settings" (iv) Select "Lamp Reset" (v) Select "Yes". Turn on...
Manual - Page 70
Appendices
RS232 Commands and Protocol Function List
RS232 Pin Assignments
RS232 shell is grounded.
9876 54321
Pin no.
1 2 3 4 5 6 7 8 9
Spec. (from projector side)
N/A RXD TXD N/A GND N/A N/A N/A N/A
English 70
Manual - Page 75
...projector meet the following specifications: Screw type: M4*3 Minimum screw length: 10mm
Please note that damage resulting from another company, please be sure to use the Optoma... If you buy a ceiling
mount from incorrect installation will vary depending on the thickness of the projector. 3. Be sure to your projector, please use the correct screw size. Screw ...
Data Sheet - Page 1
...L E T S
SET TOP BOXES
CAMCORDERS
GAME CONSOLES
D I G I TA L CAMERAS
Roku®
Apple TV® Chromecast™
With ample analog and digital connectivity, the Optoma W402 will win your audience.... Perfect for medium to large-screen applications, the Optoma W402 is ideal for projector control, Powerful 10-Watt speaker, up to 7000-hours lamp life and whisper quiet operation. HDMI 1.4a for...
Data Sheet - Page 2
...PROJECTOR - W402
OPTICAL/TECHNICAL SPECIFICATIONS
Display Technology
Single 0.65" DC3 DMD DLP® Technology by Texas Instruments™
Native Resolution
WXGA (1280 x 800)
Maximum Resolution
WUXGA (1920 x 1200)
Brightness
4500 lumens
Contrast Ratio
20,000:1
Displayable Colors
1.07 Billion
Lamp...Lens F=2.5-2.67, f=21.8-23.98 mm 1.2x manual zoom and focus
Digital Zoom
0.8 ~ 2.0
...
Optoma W402 Reviews
Do you have an experience with the Optoma W402 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Optoma yet.
Earn 750 points for your review!