Operation Manual
Page 1
Printed In USA TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Form No. 769-07548 (December 13, 2011) FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty Operator's Manual Bronco, Super Bronco & Pro-Line CRT Tillers WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
Printed In USA TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Form No. 769-07548 (December 13, 2011) FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty Operator's Manual Bronco, Super Bronco & Pro-Line CRT Tillers WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
Operation Manual
Page 2
... all models. Characteristics and features discussed and/or illustrated in this manual, all times. If you have difficulty assembling this Operator's Manual may not be necessary, should you , and any questions regarding the controls, operation, or maintenance of product specifications for purchasing a Troy-Bilt Tiller. Please be sure that this product or have any problems...
... all models. Characteristics and features discussed and/or illustrated in this manual, all times. If you have difficulty assembling this Operator's Manual may not be necessary, should you , and any questions regarding the controls, operation, or maintenance of product specifications for purchasing a Troy-Bilt Tiller. Please be sure that this product or have any problems...
Operation Manual
Page 4
...injury. 16. Keep machine, attachments and accessories in reverse or pulling machine towards you nearest servicing dealer.. Allow a machine to the operator's manual for proper tightness at too fast of a rate. 17. The governor controls the maximum safe operating speed of alcohol or drugs. 3. ...engine is to the instructions found in place and operating properly. 19. Be careful when tilling in the ground and propel the tiller forward. Important Safe Operation Practices Do not use care and good judgement. Replace gasoline cap and tighten securely. Clean up . Never...
...injury. 16. Keep machine, attachments and accessories in reverse or pulling machine towards you nearest servicing dealer.. Allow a machine to the operator's manual for proper tightness at too fast of a rate. 17. The governor controls the maximum safe operating speed of alcohol or drugs. 3. ...engine is to the instructions found in place and operating properly. 19. Be careful when tilling in the ground and propel the tiller forward. Important Safe Operation Practices Do not use care and good judgement. Replace gasoline cap and tighten securely. Clean up . Never...
Operation Manual
Page 7
... any staples from the bottom of Carton • One Tiller • One Operator's Manual • One 20 oz. Bottle SAE 10W30 Oil • One Engine Operator's Manual • One Handlebar Assembly NOTE: This Operator's Manual covers several garden tiller models. See Fig. 3-1. Lower Handlebar Hex Screw Flange ...Lock Nuts Hex Screw Knob Carriage Bolt Bell Washer Support Brackets Figure 3-1 7 Check that you have the items listed in this manual. The tiller depicted may differ from the lower handlebar and support brackets. Remove two hex screws (5⁄16-18 x 1.50), two flange ...
... any staples from the bottom of Carton • One Tiller • One Operator's Manual • One 20 oz. Bottle SAE 10W30 Oil • One Engine Operator's Manual • One Handlebar Assembly NOTE: This Operator's Manual covers several garden tiller models. See Fig. 3-1. Lower Handlebar Hex Screw Flange ...Lock Nuts Hex Screw Knob Carriage Bolt Bell Washer Support Brackets Figure 3-1 7 Check that you have the items listed in this manual. The tiller depicted may differ from the lower handlebar and support brackets. Remove two hex screws (5⁄16-18 x 1.50), two flange ...
Operation Manual
Page 9
.... Forward Clutch Cable 1. Z-Connector Reverse Clutch Cable (If so equipped) 1. Place the Z-connector into the hole in the Engine Operator's Manual packed separately with a tire gauge. Use extreme care when handling gasoline. Slide the wheel fully inward on the wheel shaft. NOTE: Before starting... area. Pull the cable up through the bottom hole of ignition. Read the instructions carefully. 3. Use the handlebar to roll the tiller to between 15 and 20 PSI. Carefully unwrap the forward clutch cable from its shipping position. Section 3 - Repeat with the other...
.... Forward Clutch Cable 1. Z-Connector Reverse Clutch Cable (If so equipped) 1. Place the Z-connector into the hole in the Engine Operator's Manual packed separately with a tire gauge. Use extreme care when handling gasoline. Slide the wheel fully inward on the wheel shaft. NOTE: Before starting... area. Pull the cable up through the bottom hole of ignition. Read the instructions carefully. 3. Use the handlebar to roll the tiller to between 15 and 20 PSI. Carefully unwrap the forward clutch cable from its shipping position. Section 3 - Repeat with the other...
Operation Manual
Page 10
... is adjustable to the separate Engine Operator's Manual. Pull the lever back and slide it up or down to the wheel shaft. In general, adjust the handlebars so they are at waist level when the tines are 3-4" in either a wheel drive or a freewheel mode. The tiller depicted may differ from yours. Handlebar... depth of the tines. Controls & Features 4 Reverse Handle Assembly Forward Clutch Bail Depth Regulator Lever Handlebar Height Adjustment Tines Wheel Drive Pin NOTE: This Operator's Manual covers several garden tiller models.
... is adjustable to the separate Engine Operator's Manual. Pull the lever back and slide it up or down to the wheel shaft. In general, adjust the handlebars so they are at waist level when the tines are 3-4" in either a wheel drive or a freewheel mode. The tiller depicted may differ from yours. Handlebar... depth of the tines. Controls & Features 4 Reverse Handle Assembly Forward Clutch Bail Depth Regulator Lever Handlebar Height Adjustment Tines Wheel Drive Pin NOTE: This Operator's Manual covers several garden tiller models.
Operation Manual
Page 11
... 3. Starting the Engine WARNING! See Fig, 5-1. Change engine oil. 2. To change the depth setting, pull back on the tiller. 5. See the Engine Operator's Manual. 7. Fill the fuel tank with the basic operation of the controls on the depth regulator lever (A) and lift up or down...position. Check the air cleaner and engine cooling system. Follow all of the tiller before using it in this Operation Section and the Engine Operator's Manual before you begin using the tiller controls without the tines engaging the soil (put tines in the garden. ...
... 3. Starting the Engine WARNING! See Fig, 5-1. Change engine oil. 2. To change the depth setting, pull back on the tiller. 5. See the Engine Operator's Manual. 7. Fill the fuel tank with the basic operation of the controls on the depth regulator lever (A) and lift up or down...position. Check the air cleaner and engine cooling system. Follow all of the tiller before using it in this Operation Section and the Engine Operator's Manual before you begin using the tiller controls without the tines engaging the soil (put tines in the garden. ...
Operation Manual
Page 14
...for all times. This untilled strip helps prevent the terraces from rolling down slopes is maintained in the normal operating position and push the tiller ahead of operation). Keep the motor oil level at the full point at each terrace. NOTE: when tilling on the ramps (if ..., be strong enough to the vehicle. • The handlers should share the load. • Use sturdy ramps and manually - Loading and unloading the tiller into and out of the tiller and any obstacles behind you . Chock the wheels with the engine shut off and apply its normal level and this ...
...for all times. This untilled strip helps prevent the terraces from rolling down slopes is maintained in the normal operating position and push the tiller ahead of operation). Keep the motor oil level at the full point at each terrace. NOTE: when tilling on the ramps (if ..., be strong enough to the vehicle. • The handlers should share the load. • Use sturdy ramps and manually - Loading and unloading the tiller into and out of the tiller and any obstacles behind you . Chock the wheels with the engine shut off and apply its normal level and this ...
Operation Manual
Page 15
.... Failure to a complete stop, disconnect the spark plug wire and move the wire away from pulling to the Engine Operator's Manual packed with your tiller for all moving parts to come to follow these instructions can result in Tires P WARNING! The air pressure should be between ...Before each first 2 hours use Every 5 Hours Every 10 Hours Every 30 Hours See Engine Manual Check Motor Oil Level PP Clean Engine P P Check Drive Belt Tension P P Check Nuts and Bolts P P Lubricate Tiller P Check Gear Oil Level in Transmission P Check Tines for Wear P Check Air Pressure in...
.... Failure to a complete stop, disconnect the spark plug wire and move the wire away from pulling to the Engine Operator's Manual packed with your tiller for all moving parts to come to follow these instructions can result in Tires P WARNING! The air pressure should be between ...Before each first 2 hours use Every 5 Hours Every 10 Hours Every 30 Hours See Engine Manual Check Motor Oil Level PP Clean Engine P P Check Drive Belt Tension P P Check Nuts and Bolts P P Lubricate Tiller P Check Gear Oil Level in Transmission P Check Tines for Wear P Check Air Pressure in...
Operation Manual
Page 16
... heaters, furnaces, etc.). When adding gear oil, use Mobil 1® Synthetic 75W 140. 8. Clean the tiller and engine. 2. Use a clean lubricating oil (#30 weight motor oil is suitable) and a clean general ... installing the tines. • Oil the threads on oil can result in the Engine Operator's Manual. See Fig. 6-2. Protect the engine and perform recommended engine maintenance by treating fuel with fuel ...fuel tank in a clean, dry area. 5. Be sure to protect the fuel lines, carburetor and fuel tank from the transmission housing and look inside the oil fill hole...
... heaters, furnaces, etc.). When adding gear oil, use Mobil 1® Synthetic 75W 140. 8. Clean the tiller and engine. 2. Use a clean lubricating oil (#30 weight motor oil is suitable) and a clean general ... installing the tines. • Oil the threads on oil can result in the Engine Operator's Manual. See Fig. 6-2. Protect the engine and perform recommended engine maintenance by treating fuel with fuel ...fuel tank in a clean, dry area. 5. Be sure to protect the fuel lines, carburetor and fuel tank from the transmission housing and look inside the oil fill hole...
Operation Manual
Page 24
...Routine maintenance items such as : grass collectors and mulch kits. Troy-Bilt LLC, P.O. To locate the dealer in accordance with the Operator's Manual furnished with respect to any kind be liable for incidental or ...tiller, to use . Transportation charges and service calls. This limited warranty shall only apply if this product (excluding its territories and possessions (either entity respectively, "TroyBilt"). No other than the original purchaser or to the person for whom it was purchased as set forth below ) against defects in materials or workmanship. "Troy-Bilt...
...Routine maintenance items such as : grass collectors and mulch kits. Troy-Bilt LLC, P.O. To locate the dealer in accordance with the Operator's Manual furnished with respect to any kind be liable for incidental or ...tiller, to use . Transportation charges and service calls. This limited warranty shall only apply if this product (excluding its territories and possessions (either entity respectively, "TroyBilt"). No other than the original purchaser or to the person for whom it was purchased as set forth below ) against defects in materials or workmanship. "Troy-Bilt...
Service Manual
Page 1
Service Manual Small Frame Troy-Bilt Tillers MTD Products LLC - Product Training and Education Department FORM NUMBER 769-01529 11/2004
Service Manual Small Frame Troy-Bilt Tillers MTD Products LLC - Product Training and Education Department FORM NUMBER 769-01529 11/2004
Service Manual
Page 5
...ENGINE: 1.1. Spark Plug Boot Grounded Figure 2.1 Coil Length - This section has been technically written to the Engine Owner's Manual for - See Figure 2.1. ward clutch spring with Serial Number 1B212G80447. Identify the engine that is fully released. Clutch Bail...Make certain the forward clutch bail is powering the tiller, and refer to follow along with the Troy-Bilt Factory School. Troy-Bilt Small Frame Tillers Troy-Bilt Small Frame Tillers TUFFY TILLER ABOUT THIS SECTION: NOTE: This section covers the Tuffy rear tine tiller, model 21A-630B063 with the forward clutch bail ...
...ENGINE: 1.1. Spark Plug Boot Grounded Figure 2.1 Coil Length - This section has been technically written to the Engine Owner's Manual for - See Figure 2.1. ward clutch spring with Serial Number 1B212G80447. Identify the engine that is fully released. Clutch Bail...Make certain the forward clutch bail is powering the tiller, and refer to follow along with the Troy-Bilt Factory School. Troy-Bilt Small Frame Tillers Troy-Bilt Small Frame Tillers TUFFY TILLER ABOUT THIS SECTION: NOTE: This section covers the Tuffy rear tine tiller, model 21A-630B063 with the forward clutch bail ...