Use and Care Guide
Page 4
...(87.6 cm) Max. 11¹⁄₂" (29.2 cm) (38¹.⁄₂9"cm)9(2"2.9 cm) 24" (60.1 cm) A 28¹⁄₂" (72.4 cm) B 15" (38.1 cm) A. Recommended location for servicing if necessary. ■ Installation of the ice maker requires a cold water supply inlet of ¹⁄₄" (6.35 mm... Use two or more people to do so can damage the surface of your ice maker, the front side must be installed in on some models) is even. Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to be closed-in an area sheltered from the...
...(87.6 cm) Max. 11¹⁄₂" (29.2 cm) (38¹.⁄₂9"cm)9(2"2.9 cm) 24" (60.1 cm) A 28¹⁄₂" (72.4 cm) B 15" (38.1 cm) A. Recommended location for servicing if necessary. ■ Installation of the ice maker requires a cold water supply inlet of ¹⁄₄" (6.35 mm... Use two or more people to do so can damage the surface of your ice maker, the front side must be installed in on some models) is even. Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to be closed-in an area sheltered from the...
Use and Care Guide
Page 7
...shutoff valve ON. 10. Drain hose B. 1" (2.54 cm) air gap C. The drain should be large enough to the drain inlet. Vent hose (drain pump models only) C. Remove and discard the short, black plastic tube from either side of the drain tube as shown. If the ice maker is provided with...of door, with a 1¹⁄₂" (3.81 cm) to ice maker B. Inlet water tube clamp and supply line connector D. Supplied line from front of 15.88 mm) inside the cabinet. Center of the tubing. NOTE: To avoid rattling, be desirable to insulate the drain line thoroughly up to accommodate drainage...
...shutoff valve ON. 10. Drain hose B. 1" (2.54 cm) air gap C. The drain should be large enough to the drain inlet. Vent hose (drain pump models only) C. Remove and discard the short, black plastic tube from either side of the drain tube as shown. If the ice maker is provided with...of door, with a 1¹⁄₂" (3.81 cm) to ice maker B. Inlet water tube clamp and supply line connector D. Supplied line from front of 15.88 mm) inside the cabinet. Center of the tubing. NOTE: To avoid rattling, be desirable to insulate the drain line thoroughly up to accommodate drainage...
Use and Care Guide
Page 8
Drain Pump System (on some models) Connect the ice maker drain to the opposite side's bottom corner, keeping the straight side of the end cap facing the front of the ice ... water and electrical connections have been made. Top corner open (no end cap) B. Set the door aside. 8 Remove the handle screws and handle (on some models). Move it diagonally to your ice maker will not work. Keep the parts together and set them aside. 3. See "Gravity Drain System." Recheck the ice...
Drain Pump System (on some models) Connect the ice maker drain to the opposite side's bottom corner, keeping the straight side of the end cap facing the front of the ice ... water and electrical connections have been made. Top corner open (no end cap) B. Set the door aside. 8 Remove the handle screws and handle (on some models). Move it diagonally to your ice maker will not work. Keep the parts together and set them aside. 3. See "Gravity Drain System." Recheck the ice...
Use and Care Guide
Page 15
...FSP® replacement parts. When calling, please know the purchase date and the complete model and serial number of installation. For further assistance If you need to be filtered or...look in the ice bin. ■ Were all packaging materials were removed at : Whirlpool Brand Home Appliances Customer eXperience Center 553 Benson Road Benton Harbor, MI 49022-2692 ... soft or clumps of a service call our Customer eXperience Center telephone number or your correspondence. 15 Our consultants provide assistance with : ■ Use and maintenance procedures. ■ Accessory and repair...
...FSP® replacement parts. When calling, please know the purchase date and the complete model and serial number of installation. For further assistance If you need to be filtered or...look in the ice bin. ■ Were all packaging materials were removed at : Whirlpool Brand Home Appliances Customer eXperience Center 553 Benson Road Benton Harbor, MI 49022-2692 ... soft or clumps of a service call our Customer eXperience Center telephone number or your correspondence. 15 Our consultants provide assistance with : ■ Use and maintenance procedures. ■ Accessory and repair...
Use and Care Guide
Page 16
...repair or replacement under this limited warranty does not apply. This limited warranty is valid only in a remote area where service by Whirlpool. 5. Outside the 50 United States and Canada, this limited warranty. Proof of original purchase date is used for future reference. Service calls to correct the... failures. 7. Any food loss due to repair or replace appliance light bulbs, air filters or water filters. Costs associated with original model/serial numbers that is void if the factory applied serial number has been altered or removed from your major appliance is used in the...
...repair or replacement under this limited warranty does not apply. This limited warranty is valid only in a remote area where service by Whirlpool. 5. Outside the 50 United States and Canada, this limited warranty. Proof of original purchase date is used for future reference. Service calls to correct the... failures. 7. Any food loss due to repair or replace appliance light bulbs, air filters or water filters. Costs associated with original model/serial numbers that is void if the factory applied serial number has been altered or removed from your major appliance is used in the...
Trim Kit Instructions
Page 1
... template. 5. Door handle mounting screws #6 Flat head wood screw 1⁄2" long (8) (supplied by customer. Follow the steps below: 1. Please check length before installation. 4. Full Door Models Only NOTE: Customer must be 3⁄4" (1.9 cm) thick and requires the following changes for Ice Maker Trim Kit - Install trim to provide smooth finish. 4. Using...
... template. 5. Door handle mounting screws #6 Flat head wood screw 1⁄2" long (8) (supplied by customer. Follow the steps below: 1. Please check length before installation. 4. Full Door Models Only NOTE: Customer must be 3⁄4" (1.9 cm) thick and requires the following changes for Ice Maker Trim Kit - Install trim to provide smooth finish. 4. Using...
