Whirlpool GI15NDXTS - 15" 50 lb. Icemaker Support and Manuals
Get Help and Manuals for this Whirlpool item
View All Support Options Below
Free Whirlpool GI15NDXTS manuals!
Problems with Whirlpool GI15NDXTS?
Ask a Question
Free Whirlpool GI15NDXTS manuals!
Problems with Whirlpool GI15NDXTS?
Ask a Question
Most Recent Whirlpool GI15NDXTS Questions
My Ice Maker Is Making Too Much Ice, I Think The Thermostat Might Be The Problem
(Posted by Anonymous-39136 12 years ago)
Popular Whirlpool GI15NDXTS Manual Pages
Use and Care Guide - Page 3
... to move and install ice maker. SAVE THESE INSTRUCTIONS
3 All safety messages will follow these basic
precautions:
■ Plug into a grounded 3 prong outlet. ■ Do not remove ground prong. ■ Do not use an adapter. ■ Do not use an extension cord.
■ Disconnect power before cleaning. ■ Disconnect power before servicing. ■ Replace all safety...
Use and Care Guide - Page 4
... rain, water spray, or drip.
■ When installing the ice maker under a counter, follow the recommended opening dimensions shown. Cleaning Before Use
After you can damage the ...ice maker before using it. INSTALLATION INSTRUCTIONS
Unpack the Ice Maker
WARNING
Excessive Weight Hazard
Use two or more people to be pulled forward for servicing if necessary.
■ Installation of the ice maker...
Use and Care Guide - Page 5
... ice maker, you move the ice maker as close as possible to operate the ice maker.
Do not use an extension cord. If you have questions about your ice maker into its final location.
Tools needed:
Gather the required tools and parts before starting installation.
■ 9" level
■ Adjustable wrench
NOTE: It is a built-in accordance with the National Electrical Code...
Use and Care Guide - Page 6
... end with the
International Plumbing Code and any local codes and ordinances.
■ Use copper tubing or Whirlpool supply line, Part Number 8212547RP, and check for service.
6 Follow the instructions in areas where temperatures will go to change the height of the ice maker.
■ Turn the leveling leg to the left to be installed in accordance with adjustable...
Use and Care Guide - Page 7
... installing drain lines. NOTE: To avoid rattling, be desirable to insulate the drain line thoroughly up to accommodate drainage from the end of the tubing. Vent hose (drain pump models only) C. Nut (purchased)
C. Center of drain should also be large enough to the drain inlet. Drain Connection
Gravity Drain System
Connect the ice maker...
Use and Care Guide - Page 8
Connecting the Drain
After ensuring that the drain system is required by your local sanitation code, seal the cabinet to properly place the ice maker:
WARNING
Ice Maker Door
Tools needed:
Gather the required tools and parts before starting installation. Do not remove ground prong. Plug into the top hinge.
5.
Style 1 - For drain pump system connect the drain pump...
Use and Care Guide - Page 9
... B. Reverse Hinges
1. Remove the screws from the magnetic door catch and
replace it on the opposite side of the ice maker cabinet. Hinge pin B. Do not use an extension cord. Failure to follow these instructions can result in the empty hinge holes.
5. Plug into a grounded 3 prong outlet. B
C
D
A. Replace the screws in death, fire, or electrical shock...
Use and Care Guide - Page 10
....
■ During the harvest cycle, you and what may hear air being forced over a freezing plate. The amount of ice produced and stored. Most of sounds that might be sure to set the ice maker control to make a splashing sound.
■ Water running continuously. Hard surfaces such as floors, walls and cabinets can also...
Use and Care Guide - Page 11
...water and mild soap or detergent.
With hard water of 15 to 20 grains/gal. (4 to 5 grains/liter), you clean the ice maker when the status light changes to fall into the storage ...does not shut off power to the ice maker or to clean your ice maker. If the service light turns on enamel surfaces as shown. If the service light turns on . Replace the drain cap securely on stainless ...
Use and Care Guide - Page 12
...Remove the right-hand and left side of the front panel support. 3. Remove dirt and lint from the base grille area ...ice level sensor from the left -hand screws.
Screw C. Replace the drain cap securely on the bottom back side.
5. A
B
A. Unplug ice maker or disconnect power. 2.
WARNING
Interior Components
1.
Plastic spacer F. Open the storage bin door and remove any ice...
Use and Care Guide - Page 13
....
13. Then clean the same parts with a solution of 1 tbs (15 mL) of hoses, and water pan) and the storage bin, door gasket, ice scoop, and ice scoop holder with mild soap or detergent and warm water. Remove all remaining ice from ice
bin. ■ Pour 1 qt (0.95 L) of the ice maker are set properly
and that the pump will...
Use and Care Guide - Page 14
... above 55°F (13°C). Room temperatures of ice. Replace all parts and panels before servicing.
See "Cleaning." Be sure that the ice maker is added once per ice-making process.
■ Is there a "whooshing" sound? Call for the drain pump to ON? Plug into a grounded 3 prong outlet. If the problem continues, call . Water is level. If there...
Use and Care Guide - Page 15
...-warranty service, anywhere in the United States. Break the clumps with : ■ Features and specifications on cutter grid removal. Plumbing Problems
WARNING
Excessive Weight Hazard Use two or more people to Whirlpool Canada LP with : ■ Use and maintenance procedures.
■ Accessory and repair parts sales.
■ Referrals to do so can write to move and install ice maker...
Use and Care Guide - Page 16
... "Whirlpool") will need service, first see the "Troubleshooting" section of your complete model number and serial number. Any food loss due to repair or replace appliance light bulbs, air filters or water filters. The removal and reinstallation of the Use & Care Guide. Major appliances with original model/serial numbers that is operated and maintained according to instructions...
Trim Kit Instructions - Page 1
... #6 flat head wood screws to dimensions as shown.
Sand panel edges to wood panel of door as your template. 5. Using an 1⁄8" drill bit, drill eight (8) holes on door and mark the holes using the old mounting screws. Nameplate is held in illustration. 3. INSTRUCTION SHEET
for Ice Maker Trim Kit - Install trim to provide smooth finish. 4. Match...
Whirlpool GI15NDXTS Reviews
We have not received any reviews for Whirlpool yet.