Whirlpool GI15NDXTS Support Question
Whirlpool GI15NDXTS Support Question
Find answers below for this question about Whirlpool GI15NDXTS - 15" 50 lb. Icemaker.Need a Whirlpool GI15NDXTS manual? We have 2 online manuals for this item!
Question posted by Anonymous-39136 on September 29th, 2011
My Ice Maker Is Making Too Much Ice, I Think The Thermostat Might Be The Problem
The person who posted this question about this Whirlpool product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Whirlpool GI15NDXTS Manual Pages
Use and Care Guide - Page 3
...We have provided many important safety messages in this manual and on your ice maker, follow instructions. All safety messages will tell you what can be killed or seriously ...DANGER
You can happen if the instructions are very important. All safety messages will follow instructions. ICE MAKER SAFETY
Your safety and the safety of others . SAVE THESE INSTRUCTIONS
3 This symbol alerts you ...
Use and Care Guide - Page 4
...Requirements
■ To ensure proper ventilation for servicing if necessary.
■ Installation of the ice maker requires a cold water supply inlet of ¹⁄₄" (6.35 mm) OD soft... (72.4 cm)
B
15" (38.1 cm)
A. Recommended location for the ice maker to be level in an area sheltered from the exterior of the
ice maker, rub the area briskly with your ice maker before using it. See "...
Use and Care Guide - Page 5
..., is a built-in death, fire, or electrical shock. Ice quality may need to make sure you have a properly grounded, 3 prong wall receptacle installed by a switch or pull chain. Recommended grounding method The ice maker must be affected. The cord must provide 1 gal. (3.8 L) of the ice maker for ice makers that a separate circuit, serving only your water pressure, call...
Use and Care Guide - Page 6
... tubing. Now you begin.
Turn off main water supply.
Turn on the bottom rear of the ice maker cabinet as shown. Using a ¹⁄₂" copper supply line with the
International Plumbing Code ... making the final connection to the inlet of the water valve to change the height of the legs as follows:
■ Turn the leveling leg to the right to lower that side of the ice maker....
Use and Care Guide - Page 7
... wall or other parts inside the cabinet. You must be centered from flowing back into the ice maker storage bin and potentially flowing onto the floor causing water damage. ■ Drain lines must have a minimum of 15.88 mm) inside
diameter.
■ Drain lines must have a 1" drop per 48" (2.54 cm drop per...
Use and Care Guide - Page 8
...straight side of the end cap facing the front of the ice maker. Recheck the ice maker to move and install ice maker. wrench
■ Flat putty knife
wrench
■ Phillips ...cannot drain, your local sanitation code, seal the cabinet to properly place the ice maker:
WARNING
Ice Maker Door
Tools needed:
Gather the required tools and parts before starting installation. WARNING...
Use and Care Guide - Page 9
... door
and set aside. 2. Remove the plastic hinge pin sleeve from the opposite side of the ice maker cabinet.
Remove the hole plugs from the "old" bottom hinge and replace it on the new ...bottom hinge pin.
4. Remove the screws from the top of the opposite side of the ice maker and tighten screws.
3. Replace the screws in the empty hinge holes.
5. Place the hinge on the ...
Use and Care Guide - Page 10
... to run a rinse cycle before starting to make ice. Fresh water enters the machine for each cycle.
■ Rattling noises may come from the flow of the ice maker can make ice. How Your Ice Maker Works
When you . If your results are unsatisfactory, your ice maker.
■ You may hear a "thud" when the ice sheet slides from the majority of water...
Use and Care Guide - Page 11
... thin ice or no ice.
5. ICE MAKER CARE
Cleaning
The ice making system and the air cooled condenser need to be turned off for the ice maker to operate at peak efficiency and to yellow. See the "Ice Maker System"... when service is complete.
NOTE: Use one bottle of 15 to 20 grains/gal. (4 to 5 grains/liter), you clean the ice maker when the status light changes to clean your water is ...
Use and Care Guide - Page 12
...all parts and panels before cleaning. Remove the two screws in ice maker or reconnect power. Cutter grid cover B. Screws
6.
Cutter grid ...ice making capacity. ■ Causes higher than recommended operating temperatures
which may lead to remove the lower access panel. Failure to do so can result in place. A
B
A. Unplug the ice level sensor from the left -hand screws. Unplug ice maker...
Use and Care Guide - Page 13
...to water valve. For ice makers with a solution of 1 tbs (15 mL) of the ...ice
bin. ■ Pour 1 qt (0.95 L) of the machine.
13 NOTE: Do not remove hoses. Check the following instructions.
■ Replace the ice scoop holder by removing the two thumb screws.
■ Wash the ice...ice from the base grille area of household bleach in ice maker or reconnect power. 17. After cleaning, make...
Use and Care Guide - Page 14
...connected?
WARNING
Ice Production
Ice maker runs but produces no ice. Do not use an extension cord. If the problem continues, call . Otherwise, bin thermostat may be ...Make sure the water supply is securely attached to purge minerals that there are no ice. The ice maker may need cleaning. The ice maker is level, and the problem persists, run a cleaning cycle.
Ice maker...
Use and Care Guide - Page 15
...ice maker. Make sure that you only use FSP® replacement parts. See "Ice Maker System" in the "Cleaning" section.
■ Are there clumps of ice...a daytime phone number in your correspondence. Plumbing Problems
WARNING
Excessive Weight Hazard Use two or more ... number in your correspondence.
15 Whirlpool designated service technicians are trained to make sure the connection is intact...
Use and Care Guide - Page 16
... REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. If outside the 50 United States and Canada, contact your sales slip together for repairs. In Canada,
call ... product service if your major appliance, to correct defects in materials or workmanship.
Outside the 50 United States and Canada, this information on the model and serial number label located on how...
Trim Kit Instructions - Page 1
... must supply #6 flat head wood screws to dimensions as shown. Sand panel edges to wood panel of customers choice. A 7/99
See
illustration. INSTRUCTION SHEET
for Ice Maker Trim Kit -
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
What are some tips regarding the ice maker in my upright freezer?
... or off the ice maker on or off? How do I turn my ice maker on my upright freezer? Discard the first three batches of ice. Side by Side with LCD Display How much ice should my ice maker make in Door, Flush Mounted Dispenser with Ice BIn in a 24-hour period? What are some tips regarding the ice maker in my upright... -
No or low ice production - Bottom freezer/French door refrigerator
... system is not jammed in 15-20 hours. If ice is not recommended to begin. Once the refrigerator is completely cooled, the ice maker should refill the ice storage bin in the ejector ...hours for a problem with Ice bin in small or hollow ice cubes. Make sure to a cold water supply and that the water shutoff valve is there no ice or not enough ice being made fast... -
The ice maker on my upright freezer is not producing ice or not enough ice
... may be a problem with the water line and you may take up or down ) position. Has the ice maker just been installed? Remove the ice from the ejector arm with frozen food. See "Ice maker" below to contact a local service professional. The ice maker on my upright freezer is not producing ice or not enough ice The ice maker on my upright...
Similar Questions
Gi15ndxtq1 Whirlpool Ice Maker.
I recently had to change the recirc. pump. Now, the ice maker forms ice on the platten but then neve...
I recently had to change the recirc. pump. Now, the ice maker forms ice on the platten but then neve...
(Posted by crumbcrusher58 11 years ago)
Ice Maker Staying Cold But Not Producing Ice. Water Going To It And It Is On,
cleaned the entire unit however, it is not producing ice. water is running to it and the unit is on ...
cleaned the entire unit however, it is not producing ice. water is running to it and the unit is on ...
(Posted by llefeve47 12 years ago)
Ice Maker Has Service Light Blinking.
I have a whirlpool gi15nfrts ice maker. Two days ago it was making ice fine but it did not stop. It ...
I have a whirlpool gi15nfrts ice maker. Two days ago it was making ice fine but it did not stop. It ...
(Posted by Artusi 13 years ago)
Why Do The Ice Maker Keep Dumping Water
(Posted by robertm01 13 years ago)