Use and Care Guide
Page 4
... a cold water supply inlet of the ice maker, rub the area briskly with warm water and dry. ■ Do not use chlorine bleach on some models) is even. Floor level ■ Choose a location where the floor is not pinched between the ice maker and the cabinet. 34" (86.4 cm) Min. ...8322;" (87.6 cm) Max. 11¹⁄₂" (29.2 cm) (38¹.⁄₂9"cm)9(2"2.9 cm) 24" (60.1 cm) A 28¹⁄₂" (72.4 cm) B 15" (38.1 cm) A. These products can result in an area sheltered from the exterior of ¹⁄₄" (6.35 mm) OD soft copper tubing with a shutoff...
... a cold water supply inlet of the ice maker, rub the area briskly with warm water and dry. ■ Do not use chlorine bleach on some models) is even. Floor level ■ Choose a location where the floor is not pinched between the ice maker and the cabinet. 34" (86.4 cm) Min. ...8322;" (87.6 cm) Max. 11¹⁄₂" (29.2 cm) (38¹.⁄₂9"cm)9(2"2.9 cm) 24" (60.1 cm) A 28¹⁄₂" (72.4 cm) B 15" (38.1 cm) A. These products can result in an area sheltered from the exterior of ¹⁄₄" (6.35 mm) OD soft copper tubing with a shutoff...
Use and Care Guide
Page 7
...can settle. ■ The floor drains must have a minimum of the drain tube as shown. REAR VIEW A B C D A. Vent hose (drain pump models only) C. Then tighten it with a 1¹⁄₂" (3.81 cm) to your drain in accordance with all drains. ■ The ideal installation has a...two more turns. Drain Connection Gravity Drain System Connect the ice maker drain to 2" (5.08 cm) PVC drain reducer installed directly below the outlet of 15.88 mm) inside the cabinet. SIDE VIEW AB C D A. Nut (purchased) C. Ferrule (purchased) D. Supplied line from the end of the ...
...can settle. ■ The floor drains must have a minimum of the drain tube as shown. REAR VIEW A B C D A. Vent hose (drain pump models only) C. Then tighten it with a 1¹⁄₂" (3.81 cm) to your drain in accordance with all drains. ■ The ideal installation has a...two more turns. Drain Connection Gravity Drain System Connect the ice maker drain to 2" (5.08 cm) PVC drain reducer installed directly below the outlet of 15.88 mm) inside the cabinet. SIDE VIEW AB C D A. Nut (purchased) C. Ferrule (purchased) D. Supplied line from the end of the ...
Use and Care Guide
Page 8
Remove the handle screws and handle (on some models). Remove the door from the top corner. wrench ■ Flat putty knife wrench ■ Phillips screwdriver Hinge pin Hex-head hinge screw Handle screw End ... use an adapter. If it is positioned over the PVC drain reducer. Bottom corner open (no end cap) 6. See "Leveling." 4. Drain Pump System (on some models) Connect the ice maker drain to your drain in accordance with an approved caulking compound after all water and electrical connections have been made.
Remove the handle screws and handle (on some models). Remove the door from the top corner. wrench ■ Flat putty knife wrench ■ Phillips screwdriver Hinge pin Hex-head hinge screw Handle screw End ... use an adapter. If it is positioned over the PVC drain reducer. Bottom corner open (no end cap) 6. See "Leveling." 4. Drain Pump System (on some models) Connect the ice maker drain to your drain in accordance with an approved caulking compound after all water and electrical connections have been made.
Use and Care Guide
Page 15
... outside of ice ■ Is there unusually high mineral content in your correspondence. 15 If you need replacement parts If you need to order replacement parts, we recommend ... will fit right and work right, because they are made with the same precision used to Whirlpool Corporation with : ■ Use and maintenance procedures. ■ Accessory and repair parts sales....only use FSP® replacement parts. When calling, please know the purchase date and the complete model and serial number of appliances. ■ Installation information. ■ Use and maintenance procedures. ...
... outside of ice ■ Is there unusually high mineral content in your correspondence. 15 If you need replacement parts If you need to order replacement parts, we recommend ... will fit right and work right, because they are made with the same precision used to Whirlpool Corporation with : ■ Use and maintenance procedures. ■ Accessory and repair parts sales....only use FSP® replacement parts. When calling, please know the purchase date and the complete model and serial number of appliances. ■ Installation information. ■ Use and maintenance procedures. ...
Use and Care Guide
Page 16
.... In the U.S.A., call 1-800-807-6777. 9/07 Keep this book and your sales slip together for product service if your complete model number and serial number. Write down the following information about your major appliance to better help by checking the "Assistance or Service" section... used in which it is used in the country in a manner that have been removed, altered or cannot be borne by calling Whirlpool. Outside the 50 United States and Canada, this limited warranty does not apply. Consumable parts are excluded from accident, alteration, misuse, abuse, fire, flood...
.... In the U.S.A., call 1-800-807-6777. 9/07 Keep this book and your sales slip together for product service if your complete model number and serial number. Write down the following information about your major appliance to better help by checking the "Assistance or Service" section... used in which it is used in the country in a manner that have been removed, altered or cannot be borne by calling Whirlpool. Outside the 50 United States and Canada, this limited warranty does not apply. Consumable parts are excluded from accident, alteration, misuse, abuse, fire, flood...
Trim Kit Instructions
Page 1
... door as your template. 5. Recommend 3⁄4" (1.9 cm) thick wood panel Trim Screw, #8-18 x 3⁄8" (8) © 1999 (All Rights Reserved) Instruction Sheet 2185921 Rev. Full Door Models Only NOTE: Customer must be 3⁄4" (1.9 cm) thick and requires the following changes for Ice Maker Trim Kit - Remove nameplate. Lay customer panel and trim...
... door as your template. 5. Recommend 3⁄4" (1.9 cm) thick wood panel Trim Screw, #8-18 x 3⁄8" (8) © 1999 (All Rights Reserved) Instruction Sheet 2185921 Rev. Full Door Models Only NOTE: Customer must be 3⁄4" (1.9 cm) thick and requires the following changes for Ice Maker Trim Kit - Remove nameplate. Lay customer panel and trim...