Whirlpool UXT4236AD Support and Manuals
Get Help and Manuals for this Whirlpool item
View All Support Options Below
Free Whirlpool UXT4236AD manuals!
Problems with Whirlpool UXT4236AD?
Ask a Question
Free Whirlpool UXT4236AD manuals!
Problems with Whirlpool UXT4236AD?
Ask a Question
Popular Whirlpool UXT4236AD Manual Pages
Installation Instructions - Page 1
...manual and on your appliance.
This is , tell you how to potential hazards that can kill or hurt you what can happen if the instructions are very important.
All safety messages will follow instructions... 36" (91.4 CM) RANGE HOOD
Installation Instructions and Use & Care Guide
For questions about features, operation/performance, parts, accessories or service, call: 1-800-253-1301 or visit...
Installation Instructions - Page 2
... ON when cooking at high settings. If you have a class...code authorities.
■ When cutting or drilling into crawl spaces, or garages. READ AND SAVE THESE INSTRUCTIONS
TABLE OF CONTENTS
RANGE HOOD SAFETY 1 INSTALLATION REQUIREMENTS 3 INSTALLATION INSTRUCTIONS 6 RANGE HOOD USE 10 RANGE HOOD CARE 10 WIRING DIAGRAM 11 ASSISTANCE OR SERVICE... service facility for examination and/or repair....
Installation Instructions - Page 3
... strong heating vents.
■ Cabinet opening dimensions that all governing codes and ordinances.
■ It is the installer's responsibility to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A, or latest edition, or with...
Installation Instructions - Page 4
...76.2 cm) minimum cabinet opening width for 30" (76.2 cm)
models and 36" (91.4 cm) minimum cabinet width for specific requirements in an attic or other enclosed area.
■ Do not use...outside temperatures as part of the vent system. Product Dimensions
2" (5.1 cm)
6 16.7 cm) or 9 24.4 cm)
4 12.5 cm)
⁷⁄₈" (2.2 cm)
29 76.0 cm) or 35 91.0 cm)
Installation Clearances
1" ...
Installation Instructions - Page 5
... Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ...(0.6 m)
1 - 90° elbow 1 - The model/serial plate is located behind the filter on the model/serial rating plate. Connect a section of the above code standards can be obtained from:
National Fire Protection Association 1 ...
Installation Instructions - Page 6
Replace all parts and panels before servicing. IMPORTANT: The brackets should touch the upper cabinet.
Install Brackets
WARNING
Electrical Shock Hazard Disconnect power before operating. Failure to "Venting System" in death or electrical shock.
2. Mark Hole Locations
■ Using a #2 Phillips screwdriver, install the drywall anchors.
■ Using #8-18 x 1" (4.2 x 25 mm) flat...
Installation Instructions - Page 7
...set it aside.
■ Using the 7" (17.8 cm) round vent mounting plate, draw the vent opening outline on the rear of the cabinet:
- For a non-vented (recirculating) installation: Go to Step 7. For a rear vented installation... and bend each mounting tab (A) upward approximately 90°. For a top vented installation: Mark the 4 vent hole locations (C) on the cabinet bottom.
■ Using...
Installation Instructions - Page 8
... W10355451, and a 7" (17.8 cm) round vent mounting plate (B), Part Number W10388168, are available as shown in Step 8. Drill Electrical Opening
9. Insert the screws approximately 2 turns into the mounting tab (F) on ordering, see the "Assistance or Service" section.
■ If installing the optional round damper, position it interferes with the rectangular damper, remove the...
Installation Instructions - Page 9
... Installation
■ Install a 120V, 75W maximum, incandescent light bulb with this model range hood.
13. Attach the screws to the cabinet side walls.
■ For direct wire installations...installations, follow the instructions supplied with vent clamps or duct tape to the range hood. See "Metal or Charcoal Grease Filter" in the "Range Hood Care" section.
■ If removed previously, replace...
Installation Instructions - Page 10
... instructions.
Exterior Surfaces: IMPORTANT: Do not use . For vented installations: Wash the metal filter as needed in the grease filter retainer.
10 Dispose of the range hood. Replace the... use Stainless Steel Cleaner and Polish, Part Number 31462A (not included): See the "Assistance or Service" section to order.
■ For stainless steel models, rub in the direction of the ...
Installation Instructions - Page 11
...10% Ohms
White - Black 13.6 ±10% Ohms
Ground Screw
L N GND SE114A
11 Replacing the Incandescent Light Bulb Turn off the range hood and allow the light bulb to cool.
1.
On... 3 Low 1 - If the new light does not operate, make sure the light bulb is inserted correctly before calling service. L High
Rectifier
Diode
NOTE: Speed 1 not used
W
R
Speed 1
W Common
Speed 2
R
BK
C25
Motor...
Installation Instructions - Page 12
... OR SERVICE
If you need to order replacement parts, we recommend that you use only factory specified parts. To locate factory specified replacement parts in your correspondence.
12 Our consultants provide assistance with: ■ Scheduling of appliances.
■ Referrals to local dealers.
■ Installation information.
■ Use and maintenance procedures.
■ Accessory and repair...
Installation Instructions - Page 13
... you specific legal rights, and you also may not apply to you. Please take a few minutes to review the Troubleshooting or Problem Solver section of purchase, when this major appliance is used in the country in accordance with published user, operator or installation instructions.
2. All warranty service is required to correct improper product maintenance or installation, installation not...
Whirlpool UXT4236AD Reviews
We have not received any reviews for Whirlpool yet.