Home » Hayward » Pool & Spa » Hayward HCC 2000

Hayward HCC 2000 Support Question

Find answers below for this question about Hayward HCC 2000.
Need a Hayward HCC 2000 manual? We have 2 online manuals for this item!

Hayward Overview Questions Manuals Reviews Videos Research

Question posted by davediehl20 on July 13th, 2019

Hayward Hcc 2000 Controller. No Power To Chlorinator Solenoid Vale From Contrlle

No power from controller to solenoid in automatic or manual mode.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by techyagent on July 29th, 2019 1:31 AM

This answer was accepted by the poster of the original question.

techyagent

Member since:
June 17th, 2014

Points: 4,799,770

1,100
points

If the power is not passing through to chlorination valve so it means there is some debris blockage inside the machine which you need to be aware of. You can do one thing open it and try to remove the valve and the chlorination and put them in the vinegar it will surely help to improve the flow.

Thanks

Techygirl

Related Hayward HCC 2000 Manual Pages

HCC 2000 Manual - Page 4

... typical chlorine levels when chemistry is adjusted manually versus automatically with Health Department chemistry standards, reduced burden on operating staff, and a reduction of chemicals on a basis proportional to the demand. MANUAL -VS- CHEMICAL AUTOMATION WITH THE HCC 2000 A pool operator typically checks and adjusts pool or spa water chemistry hourly at best. The HCC 2000 continuously...

HCC 2000 Manual - Page 5

...HCC 2000 controller unit also features an internal micro-computer for pH, and mode selections to maximize sensor performance and life. If pH is maintained above 7.6 (too alkaline), sanitizer activity is an actual measure of sanitizer activity (chlorine... conditions to manually feed or disable feeding for pools and spas is preset from the factory to the pool or spa surface can occur...

HCC 2000 Manual - Page 9

.... HCC 2000 INSTALLATION DIAGRAM HCC 2000 SYSTEM Power Cord Influent (to Return Line) Effluent (to the controller unit as labeled. 12. Sensor cables are to be used with the controller, install according to the controller as... CAT CO2 or pH Control Flow Cell / Flow Sensor Bypass Line Flow Solenoid Flow Flow Flow WASTE Chemical Pump or Erosion Feeder Solenoid Main Drain and Skimmer ...

HCC 2000 Manual - Page 10

...® water quality controllers maintain sanitizer levels (chlorine, bromine, ozone, etc.) based on and setting up the HCC 2000. Hayward® strongly recommends establishing desired pH, sanitizer residual, calcium hardness, total alkalinity, temperature and cyanuric acid levels prior to provide consistent sanitizer residual levels rather than consistent control of the pool or spa. The ORP...

HCC 2000 Manual - Page 12

The controller will automatically return to the normal operating mode after twenty seconds, storing any changes. Manually test pool or spa to confirm that the current sanitizer reading (chlorine, bromine, etc.) is the level you wish to maintain ORP at 7.5. ALL RIGHTS RESERVED Changing the pH Setpoint The HCC 2000 is preset from the factory to maintain. 2. Press the arrow...

HCC 2000 Manual - Page 14

... Button 7 ORP Channel Decrease Button 8 ORP Channel Setpoint Adjustment Button 9 ORP Channel Mode Selection Button HCC 2000 pH/ORP CONTROLLER FEED pH1 ALARM ORP FEED ALARM 2 3 6 7 SETPOINT ADJUSTMENT 4 SET CALIBRATE SETPOINT ADJUSTMENT 8 SET pH FEED MODE 5 AUTO OFF MANUAL ORP FEED MODE 9 AUTO OFF MANUAL CONTENTS COPYRIGHT 2010 HAYWARD INDUSTRIES, INC. ILLUSTRATION 4.

HCC 2000 Manual - Page 15

Advanced (Dealer) Setup Options The HCC 2000 controller incorporates an advanced programming menu and enhanced features. No-Flow Alarm The no-flow alarm displays the prompt on the LED displays, in addition to activating both channel Alarm indicators and sounding the audible alarm: no Flo Power On Display At power on the ORP channel LED display...

HCC 2000 Manual - Page 24

...HCC 2000 controller provides instrument-grade accuracy which exceeds that the sensors are in pool or spa water, the sensors may be clean and free from the flow cell. Hand tighten only. CONTENTS COPYRIGHT 2010 HAYWARD...the bottom of cleaning. MAINTENANCE HCC 2000 CONTROLLER The HCC 2000 controller unit is important to calibrate pH using a quality manual test kit. It is ...

HCC 2000 Manual - Page 25

... damage by electro-static discharge (ESD) when the sensor cables are freezeresistant, they must be drained prior to exposure to storing or transporting the HCC 2000 controller unit. Although Hayward® sensors are disconnected. Always reinstall the BNC protective covers prior to freezing temperatures. The flow cell and poly tubing must be protected from...

HCC 2000 Manual - Page 26

...controller is properly set for proper operation. Both pH and ORP digital readouts display illogical values. 1. Ensure that acid/base feed mode is powered on. 1. ALL RIGHTS RESERVED TROUBLESHOOTING Each HCC 2000 controller... 2010 HAYWARD INDUSTRIES, INC. Most apparent malfunctions can be reversed. Ensure that flow sensor is selected. 3. Make sure "auto" ORP feed mode is not...

HCC 2000 Complete Pack Manual - Page 4

... maintenance of chemical levels twenty-four hours a day, compliance with the HCC 2000 controller. AUTOMATED CONTROL CONTENTS COPYRIGHT 2010 HAYWARD INDUSTRIES, INC. ALL RIGHTS RESERVED The following graph (Illustration 1.) compares typical chlorine levels when chemistry is adjusted manually versus automatically with Health Department chemistry standards, reduced burden on operating staff, and...

HCC 2000 Complete Pack Manual - Page 5

... actual measure of sanitizer activity (chlorine, bromine, ozone, etc.) and bacteriological water quality rather than an expression of chemical residual levels. ORP is reduced, water may become cloudy, and eye irritation may result. The HCC 2000 controller is preset from the filtration system and sends signals to the pool or spa surface can occur. The unit...

HCC 2000 Complete Pack Manual - Page 9

... Flow Flow WASTE Chemical Pump or Erosion Feeder Solenoid Main Drain and Skimmer SUCTION LINE Flow RETURN LINE PUMP Flow FILTER ALL CHEMICALS MUST BE INJECTED DOWN STREAM FROM HEATER & FLOW CELL Pressure Differential HCC 2000 INSTALLATION DIAGRAM HCC 2000 SYSTEM Power Cord Influent (to Return Line) Effluent (to the controller as labeled. These covers protect the...

HCC 2000 Complete Pack Manual - Page 10

...Hardness 200 IDEAL 7.5 2 3 - Hayward® water quality controllers maintain sanitizer levels (chlorine, bromine, ozone, etc.) based on and setting up the HCC 2000. CONTENTS COPYRIGHT 2010 HAYWARD INDUSTRIES, INC. Although ORP is to initiating automated control of the pool or spa. Always maintain water chemistry according to the following ranges before powering on ORP. SECTION 6. The...

HCC 2000 Complete Pack Manual - Page 11

... the HCC 2000 are ready to the normal operating mode after twenty seconds, storing any changes. The controller will display an "A" or "B" indicating whether acid feed or base feed mode has been activated. Please refer to select A for acid feed or B for controller unit button designations. As the unit powers on, the digital pH readout will automatically return...

HCC 2000 Complete Pack Manual - Page 12

... set pH control at 7.5. Manually test pool or spa to confirm that the current sanitizer reading (chlorine, bromine, etc.) is the level you wish to the normal operating mode after twenty ...HAYWARD INDUSTRIES, INC. Press the ORP Setpoint Adjustment Button (#8) until the green "SET" LED is illuminated. 2. Changing the pH Setpoint The HCC 2000 is preset from the factory to the normal operating mode...

HCC 2000 Complete Pack Manual - Page 15

... Setup Mode Find the Hidden Button (#1) located behind the large pH text over the pH digital display. 1. Press and hold the Hidden Button (#1) for five seconds to make a selection. b Base feed selected. Press the Up (#6) and Down (#7) arrow buttons to scroll through programming options. 3. SECTION 9. Advanced (Dealer) Setup Options The HCC 2000 controller incorporates...

HCC 2000 Complete Pack Manual - Page 24

...pool or spa water, the sensors may be performed using commercially available reference solutions. A household liquid dishwashing detergent may damage the enclosure and membrane switch panel. MAINTENANCE HCC 2000 CONTROLLER The HCC 2000 controller...SECTION 11. To maintain a consistent sanitizer residual in this manual. Never allow a pH or ORP sensor to ORP. It is virtually maintenance ...

HCC 2000 Complete Pack Manual - Page 25

... if sensors are freezeresistant, they must be drained prior to exposure to storing or transporting the HCC 2000 controller unit. Although Hayward® sensors are to withstand a broad temperature range, winter storage in small glass or plastic containers with genuine HCC Professional Series sensors PRO15-2 and PRO25-2. WINTERIZATION The sensors should be protected from freezing...

HCC 2000 Complete Pack Manual - Page 26

.... CONTENTS COPYRIGHT 2010 HAYWARD INDUSTRIES, INC. SECTION 12. Ensure that acid/base feed mode is selected. 3. pH chemical feeder is in balance. State of the art design and fabrication technology ensure years of trouble free operation. Both pH and ORP digital readouts display illogical values. 1. ALL RIGHTS RESERVED TROUBLESHOOTING Each HCC 2000 controller is selected...