Sony KDF-70XBR950 Support Question
Sony KDF-70XBR950 Support Question
Find answers below for this question about Sony KDF-70XBR950 - 70" Rear Projection TV.Need a Sony KDF-70XBR950 manual? We have 1 online manual for this item!
Question posted by sleepydocmario on May 4th, 2011
Tv Won't Turn On
I attempt to turn on the TV and the power/standby light blinks green for a second then ambert and then the red light comes on and blinks for a while before it turns solid red again. I have unpluged it. What do you think it could be?
Current Answers
Related Sony KDF-70XBR950 Manual Pages
Operating Instructions - Page 2
... by turning the ...Projection TV to the point of cable entry as practical. Model No. However, there is no guarantee that the cable ground shall be connected to the grounding system of the building, as close to rain or moisture. MODEL: KDF-60XBR950, KDF-70XBR950...television receiver for other outlet unless the blades can be fully inserted to prevent blade exposure. You are located at the rear...
Operating Instructions - Page 3
... screen to fit into the outlet, contact your dealer. ❑ If any liquid or solid object should fall inside the cabinet, unplug the LCD Projection TV immediately and have it checked by qualified service personnel before turning on the LCD Projection TV. ❑ To obtain the best picture, do not block the
ventilation openings. ❑ Do...
Operating Instructions - Page 5
...turn the set off . When the set through the cabinet slots as these slots and openings must never be blocked or covered. ❑ Never cover the slots and openings
with a solution of mild detergent and water. ❑ Do not use power...swimming pool, etc. If the picture becomes dark after using the LCD Projection TV for example, near water -
An appliance and cart combination should be ...
Operating Instructions - Page 11
... finishing. Read the instructions "Use of your LCD projection
TV is in use.
Note the following:
❑ After turning on your LCD
projection TV will not turn on .
11 To avoid eye discomfort or injury, do not look into the housing when the power is quite bright when your LCD projection TV.
Replace the lamp with a new Sony XL...
Operating Instructions - Page 12
... for several minutes after turning the power off when unplugging from the outlet or switching the breaker off the power switch on the main unit or on the remote
control. Introducing the Sony LCD Projection TV
Notes on the LCD Projection TV
To enjoy clear pictures ❑ Be sure not to allow sunlight or light from a lamp to...
Operating Instructions - Page 13
... supplied) for any object inside the lamp receptacle of the LCD projection TV after the power has been turned off.
❑ Do not leave the removed lamp near flammable materials or within the reach of the LCD projection TV flashes, it may damage the LCD projection TV.
❑ Do not remove the lamp for replacement. Doing so may...
Operating Instructions - Page 14
...the upper of the control panel cover to blow for about two minutes after turning off .)
✍ Do not touch the front glass of a new lamp...power cord after turning the power off the main power. Take the new lamp out of the box.
3 Remove the control panel cover. Introducing the Sony LCD Projection TV
1 Turn off the power switch on the LCD projection TV and after several
minutes, unplug the power...
Operating Instructions - Page 16
... and the POWER/STANDBY indicator flashes for three times.
8 Mount the front panel in the order of the right side.
3 Close the front panel.
✍ Consult your Sony dealer for a Sony XL-2100U replacement lamp. ✍ Take great care when replacing the lamp or plugging in the
illustration.
1 Match the projection of the...
Operating Instructions - Page 22
... Projection TV Rear and Front Panel Connectors
Rear of LCD projection TV
22 Installing and Connecting the LCD Projection TV
Item 1 Memory Stick slot
2 Memory Stick indicator
3 POWER
Description
Memory Stick insertion slot.
When lit, indicates that the Memory Stick is being read. (Do not remove the Memory Stick when the indicator is lit.)
Press to turn on page 66...
Operating Instructions - Page 23
...connection with the VHF/UHF input jack, lets you set up your LCD projection TV to switch between scrambled channels (coming through a cable box) and unscrambled cable channels. To open and close the.../UHF 2 CABLE
3 i.LINK 4 S VIDEO
(Front and rear)
5 VIDEO/ (L/R) AUDIO (Front and rear)
Description
Connects to i.LINK-compatible devices.
Connects to your VCR or other S VIDEO-equipped...
Operating Instructions - Page 26
...Shown
VHF Only or combined VHF/ UHF
75-ohm coaxial cable
Rear of LCD projection TV
VHF/UHF
Cable
75-ohm coaxial cable
Rear of LCD projection TV
CABLE
300-ohm twin lead cable (usually found in older homes... As Shown
VHF Only or UHF Only or combined VHF/UHF
300-ohm twin lead cable
Rear of LCD projection TV VHF/UHF
Antenna connector (not supplied)
75-ohm coaxial and 300-ohm twin lead cable ...
Operating Instructions - Page 30
... company scrambles all channels come into the LCD projection TV through the cable box to the LCD projection TV's VHF/UHF jack. ...Rear of your cable box and only one unscrambled signal is set to (usually channel 3 or 4) and then use a
cable box. ❑ You do this connection, all channels, which requires you can: ❑ Use the LCD projection TV remote control to the LCD
projection TV...
Operating Instructions - Page 32
Rear of LCD projection TV
Coaxial cable
32
S VIDEO
VIDEO (yellow) AUDIO-L (white) AUDIO-R (red)
VCR
VC-810S/ 820S/830S (not supplied)
Cable
S video cable (not supplied)
✍ If your VCR is not equipped with S VIDEO, use a VIDEO cable (yellow)
instead of the S VIDEO cable. Disconnect all power sources before making any connections.
1 Connect the cable...
Operating Instructions - Page 34
Installing and Connecting the LCD Projection TV
Rear of LCD projection TV
Coaxial cable
If you are connecting a digital cable box, you will ... box (scrambled) and those coming directly to channel 3 or 4, depending on your cable box channel output.
✍ Pressing ANT on the VCR. Coaxial cable
CATV cable
34
Splitter
S VIDEO
VIDEO (yellow) AUDIO-L (white) AUDIO-R (red)
VCR
VC-810S/820S/...
Operating Instructions - Page 35
... and VIDEO IN jacks. Rear of the yellow video cable on your VCR. Consult your
VCR's operating manual for instructions.
✍ If your VCRs have an S VIDEO jack: For best picture quality, use an
S VIDEO connection instead of LCD projection TV
VCR (playback)
VCR (recording)
AUDIO-R (red) AUDIO-L (white)
VIDEO (yellow)
VC-810S/820S...
Operating Instructions - Page 111
... this is Auto.
Dotted lines or stripes
❏ Adjust the antenna. ❏ Move the LCD projection TV away from 1 to reset Setup selections.) To turn on, and a red light keeps flashing, your local Sony Service Center.
❏ Make sure the power cord is plugged in the Setup Menu and no picture (screen lit), good sound
❏...
Operating Instructions - Page 113
... STANDBY LED blinks when the signal from the selected device.
Turn the... other ❏ Be sure the Video Label option is not available.
Other Information
113 The signal from a selected i.LINK device is being displayed
❏ If you have several i.LINK devices connected and operating at once, the LCD projection TV...
Operating Instructions - Page 114
... (see page 16). The POWER/STANDBY (green) indicator flashes. ❑ The lamp for the light source burns out.
The LAMP indicator flashes. ❑ The lamp for the light source is ready to turn on the Front of the Monitor
LAMP
TIMER
i.STANDBY POWER/STANDBY
The POWER/STANDBY (green or red) and/or LAMP (red) indicators indicate the conditions of the LCD projection TV and warnings by...
Operating Instructions - Page 118
...61
H
Hue, adjusting 88
I i.LINK 10, 80-86
i.LINK Standby 105 Image Shift 105 Inputs, labeling 103
Installation of the projection TV 25-44
interlaced 107
J
JUMP button 47 Jump, using 52
L
... (GREEN) 47 POWER/STANDBY 114 Presetting channels 45
problems, troubleshooting 108-113
Program Guide 60 Program Options menu 61 progressive 107
R
Ratings setting 99 viewing blocked programs 99
Rear panel controls ...
Operating Instructions - Page 119
... sound 92
T
Timer set current 104
Timer setting 104 Treble, adjusting 92
troubleshooting 108-113
TV function button 46 TV power button 47 TV/VIDEO button 47 Twin View™
activating a picture 55 described 9 using 55
V
VCR using with TV remote control 50 with cable box, connecting 33 with cable, connecting 32 with Twin View...
Similar Questions
What Is The Process To Replace Ballast On This Tv
Is there a video or step by step instructions and how do i test the one on tv to know if it is bad o...
Is there a video or step by step instructions and how do i test the one on tv to know if it is bad o...
(Posted by rocky5750 9 years ago)
Power/standby Light Blinks And Tv Goes Off And The Back On
(Posted by wademcginnis 11 years ago)
Sony Fs57m91 Rear Projection Television.
My Sony television, when powered on, goes to standby mode with led blinking thrice before repearing ...
My Sony television, when powered on, goes to standby mode with led blinking thrice before repearing ...
(Posted by rhljain 11 years ago)
Hello - I Own A Sony Kdf-70xbr950 Tv. The Lamp Was Burned Out. I Just Replaced I
Hello - I own a Sony KDF-70XBR950 TV. The lamp was burned out. I just replaced it with a bracnd new ...
Hello - I own a Sony KDF-70XBR950 TV. The lamp was burned out. I just replaced it with a bracnd new ...
(Posted by harveyrt 12 years ago)
Tv Will Not Come On The Stand-by Blinks Green And Then Red Lite Blinks Lamp
(Posted by bluegrassinc 12 years ago)