Home » Troy-Bilt » Lawn & Garden » Troy-Bilt TB675

Troy-Bilt TB675 Support Question

Find answers below for this question about Troy-Bilt TB675.
Need a Troy-Bilt TB675 manual? We have 1 online manual for this item!

Troy-Bilt Overview Questions Manuals Reviews Videos Research

Question posted by Reynaldoher98 on May 21st, 2016

Fuel Lines

I'm having trouble knowing where to correctly place the 3 fuel lines any help?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by waelsaidani1 on May 21st, 2016 11:45 PM

This answer was accepted by the poster of the original question.

waelsaidani1

Member since:
May 12th, 2013

Points: 19,501,787

1,070
points

Hello here is a video guide: https://www.youtube.com/watch?v=sfSg0oOT9EM

Related Troy-Bilt TB675 Manual Pages

Operation Manual - Page 1

... parts. 769-08458 / 02 All information, illustrations, and specifications in Canada. Operator's Manual Electric Start Capable 4-Cycle Trimmer TB675 EC TABLE OF CONTENTS Service 1 Safety 2 Know Your Unit 5 Specifications 5 Assembly 6 Oil and Fuel 8 Starting and Stopping 10 Operation 12 Maintenance 13 Cleaning and Storage 17 Troubleshooting 18 Warranty 20 SAVE THESE INSTRUCTIONS...

Operation Manual - Page 2

... dangers. Please read these requirements. Never use the trimming line described in property damage or injury to yourself or to ... or a fine. Forest Land and in place. • Avoid creating a source of ignition for later use. •... by themselves eliminate any spilled fuel from the unit immediately, before fueling. • Always add fuel in serious injury to the operator...

Operation Manual - Page 3

... is generally an indicator of trouble. WHILE OPERATING • Wear.... • Never store the unit with fuel in the tank, inside a building where fumes...line installed. Only use . • Do not force the unit. It will do the job. If it does not, take the unit to an authorized service dealer for an adjustment. • Adjust the handle to prevent unauthorized use . Vibration is not in place...

Operation Manual - Page 4

...this product. Read the operator's manual for the proper type of oil. • DO NOT USE E85 FUEL IN THIS UNIT WARNING: It has been proven that may get extremely hot from the operating area. •...; HOT SURFACE WARNING: Do not touch a hot muffler or cylinder. Failure to do not touch the line cutting blade. 4 To prevent serious injury, do so can be used in serious injury to operator's ...

Operation Manual - Page 5

...head shield and handle 13 - 14 lbs. (5.9 - 6.4 kg) Trimmer Mechanism Bump Head Trimming Line Diameter 0.095 inches (2.41 mm) Cutting Path Diameter 17 in . (0.635 mm) Spark Plug... Throttle Control Fuel Cap Choke Lever Coupler Oil Fill Plug Cutting Head Cutting Head Shield Line Cutting Blade SPECIFICATIONS* Engine Type Air-Cooled, 4-Cycle Displacement 30 cc (1.83 cu. KNOW YOUR UNIT ...

Operation Manual - Page 6

.... 1. Loosen the bolt with a 3/8" socket, but do not tighten the bolt completely. 3. Place it a minimum of 6 inches (15.24 cm) from the end of the shaft grip (Fig. 2). 4. Tighten the bolt... with a 3/8" socket (Fig. 2). 2. Place the cutting head shield onto the mount bracket. Push the handle down onto the shaft housing (Fig. 2). ...

Operation Manual - Page 7

... any attachment, read and understand the manual that came with the guide recess will help installation (Fig. 4). 3. Installing the Attachment NOTE: Remove the protective cap and gray... button is securely tightened. CAUTION: Before operating the unit, make installing or removing the attachment easier, place the unit on the ground or on a work bench. Using the wrong hole could lead to personal...

Operation Manual - Page 8

... Fig. 6 O-Ring Oil Fill Hole Fig. 7 8 NOTE: This unit was shipped without oil in place on a flat, level surface. 4. Unscrew the top of maintaining the proper oil level cannot be added before... the bottle to the Maintenance Schedule. OIL AND FUEL USING THE RIGHT OIL Use a high-quality SAE 30 weight oil. Change the oil according to measure the correct amount of the oil bottle. 2. Cut the...

Operation Manual - Page 9

...: DO NOT USE E85 FUEL IN THIS UNIT. WARNING: Add fuel in place. Do not start the engine until fuel vapors dissipate. 1. Move the unit at a distance from fuel spray. Position the unit with the fuel cap facing up any spilled fuel immediately. Using Fuel Additives Use a fuel additive, such as 1% water in the fuel can make fuel and oil separate...

Operation Manual - Page 10

...to squeeze the throttle control. Starter Rope Grip Starting Position Throttle Control Fig. 11 10 Fill the fuel tank. Refer to Position 3. The On/Off switch is no need to Position 1 (Fig. 10...to squeeze the throttle control. Refer to start after a few attempts, move the choke lever to Fueling the Unit. Slowly press and release the primer bulb 10 times (Fig. 9). 4. Squeeze the ...

Operation Manual - Page 11

... 3. Fig. 12 Electric Start Port STOPPING INSTRUCTIONS 1. Refer to turn the unit on. Fill the fuel tank. Slowly press and release the primer bulb 10 times (Fig. 9). 4. Continue to squeeze the... starts. the engine fails to a complete stop (Fig. 8). 11 perform steps 3 - 10 to Fueling the Unit. Refer to restart the engine. Run the electric start accessory for 2-5 minutes, or as ...

Operation Manual - Page 12

... serious personal injury or damage to the proper length if any excess line is equipped with the right hand. NOTE: Some line breakage will occur from the cutting head without the need for bending over... unit so that it easily contacts the grass without stopping the engine. ADJUSTING THE TRIMMING LINE LENGTH This unit is released. A blade in the cutting head shield will make the unit overheat...

Operation Manual - Page 13

... TRIMMING LINE Only use the correct line length when installing trimming line. If necessary, remove any seasonal tune-up. Refer to Maintaining the Air Filter. • Change the oil. Push the line through.... Refer to cool before servicing or repairing the unit. WARNING: Never use metal-reinforced line, wire, chain or rope. These can break off and become dangerous projectiles. NOTE: The...

Operation Manual - Page 14

...spool (Fig. 18). NOTE: Make sure the O-ring is too low, add oil. Firmly press in place on the cutting head (Fig. 18). 2. Wipe up the oil level window (Fig. 20). Remove the...(Fig. 18). 3. Remove any oil that the engine is approximately halfway up any old trimming line and/or obstructions. 4. The cutting head shield should fill the window approximately halfway (Fig. 20...

Operation Manual - Page 15

.... Cleaning the Air Filter 1. Reinstall the air filter in place on the air filter cover into the oil fill hole. ...maintenance is not covered by the product warranty. oz (60 ml) fill line indicated on the air filter housing. NOTE: Make sure the O-ring ... result in detergent and water. Squeeze the air filter to measure the correct amount of the bottle (Fig. 22). 6. The oil will VOID ...

Operation Manual - Page 16

...Reattach the spark plug boot. Release the throttle control and let the engine idle. Checking the fuel, cleaning the air filter, and adjusting the idle speed should make carburetor adjustments. Remove the spark... torque to set the air gap at a time (as follows: 1. If, after checking the fuel and cleaning the air filter, the engine still will not idle • the engine hesitates or stalls...

Operation Manual - Page 17

.... Refer to federal, state and local regulations. 17 This ensures that all of the oil from the carburetor. 3. Remove the spark plug and drain all fuel has been drained from the cylinder. 2. Wipe off any high quality motor oil into an approved container. Long-term Storage 1. Short-term Storage (1-2 weeks) 1. Do...

Operation Manual - Page 18

... head Clean or replace the air filter Drain the fuel tank and add fresh fuel Clean or replace the air filter Replace the spark plug THE CUTTING HEAD WILL NOT ADVANCE LINE The cutting head is bound with grass The cutting head is out of line The inner reel is bound up The cutting...

Operation Manual - Page 20

...purpose. No product returned directly to the parts as identified. Bump Knobs, Outer Spools, Cutting Line, Inner Reels, Starter Pulley, Starter Ropes, Drive Belts, Saw Chains, Guide Bars, Cultivator...design of any Troy-Bilt Product without limitation, expenses incurred for substitute or replacement lawn care services, for transportation or for related expenses, or for rental expenses to ...